LIGHTING SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. LED Headlight System

    Component
    Function
    LED Driver Module
    Supplies a constant current to the LED when power is supplied from the integration relay. Sends a normal illumination signal to the main body ECU while the headlight low beam is illuminated normally.
    Main Body ECU
    1. Controls the integration relay which supplies power to the LED drive module.
    2. Determines a failure in the LED headlight in accordance with the signal from the LED module and light control switch conditions and outputs a warning request signal to the combination meter assembly.
    Combination Meter Assembly
    Multi-information Display
    Receives the LED headlight warning request signal from the main body ECU and displays a warning message.
    Headlight Indicator Light
    Illuminates the headlight indicator light while the headlight low beams are illuminated.

  2. Automatic Headlight Beam Level Control System

    Component
    Function
    Headlight Leveling ECU
    1. The headlight leveling ECU detects changes in the vehicle movement based on the vehicle speed signals from the rear height control sensor and combination meter assembly.
    2. Outputs control signal to the headlight leveling motor.
    3. Provides initial set control, fail-safe function and diagnosis function.
    Headlight Assembly
    Headlight Leveling Motor
    1. Based on the signals received from the headlight leveling ECU, the motors move the reflectors in the headlights.
    2. Uses a headlight leveling motor to precisely regulate the angle of the reflectors.
    Rear Height Control Sensor Sub-assembly
    The rear height control sensor sub-assembly detects vehicle movement and transmits a signal to the headlight leveling ECU.
    Light Control Switch
    The light control switch transmits a HEAD position signal to the main body ECU.
    Main Body ECU
    The main body ECU receives HEAD position signals from the light control switch and sends headlight status signals to the headlight leveling ECU.
    Combination Meter Assembly
    Headlight Leveling Indicator Light
    When the system malfunctions, the combination meter assembly alerts the driver by illuminating the headlight leveling indicator light in accordance with the signals from the headlight leveling ECU.

  3. Automatic Light Control System

    Component
    Function
    Automatic Light Control Sensor
    The automatic light control sensor detects the ambient light level.
    Light Control Switch
    The light control switch transmits an AUTO position signal to the main body ECU.
    Main Body ECU
    The main body ECU receives signals from the automatic light control sensor and AUTO position signals from the light control switch, and illuminates the headlights, taillights, parking lights, side marker lights and license plate lights.
    Engine Room Relay Block
    Integration Relay
    The integration relay supplies power to the headlight low beams.
    Instrument Panel Junction Block Assembly
    Taillight Relay
    The taillight relay supplies power to the taillights, parking lights, side marker lights and license plate lights.
    Combination Meter Assembly
    Headlight Indicator Light*1
    The headlight indicator lights up to inform the driver when the headlights turn on.
    Taillight Indicator Light*2
    The taillight indicator lights up to inform the driver when the taillights turn on.

    1. *1: Models for U.S.A.
    2. *2: Models for Canada

  4. Light Auto Turn-OFF System

    Component
    Function
    Main Body ECU
    The main body ECU receives various signals, and turns off the exterior lights.
    Door Courtesy Light Switch
    Front LH/RH, Rear LH/RH, Back Door
    The courtesy switch detects whether a door is open or closed and transmits a signal to the main body ECU.
    Door Lock Assembly
    Front LH/RH, Rear LH/RH, Back Door
    The door lock assembly detects the whether a door is locked or unlocked and transmits a signal to the main body ECU.
    Engine Room Relay Block
    Integration Relay
    The integration relay supplies power to the headlight low beams.
    Instrument Panel Junction Block Assembly
    Taillight Relay
    The taillight relay supplies power to the taillights, parking lights, side marker lights and license plate lights.
    Foglight Relay
    The foglight relay shuts down the power to the front fog lights.
    Certification ECU
    The certification ECU judges and certifies the ID code from the door control receiver.
    Light Control Switch
    The light control switch transmits a light control position signal to the main body ECU.

  5. Daytime Running Light System

    Component
    Function
    Main Body ECU
    Receives the READY signal from power management control ECU and outputs daytime running light illumination signal to the running light relay.
    Engine Room Relay Block
    Running Light Relay
    Receives the signal from the main body ECU, performs the high-speed switching operation and then illuminates and dims the high beams.
    Power Management Control ECU
    The power management control ECU outputs an READY signal and transmits it to the main body ECU.
    Light Control Switch
    The light control switch outputs a light control signal and transmits it to the main body ECU.


SYSTEM CONTROL


  1. LED Headlight System

    1. When the light control switch is turned ON, the LED driver modules immediately turn on the LEDs (approximately 0.1 sec). In addition, by regulating the output currents flowing into the LEDs at the specified level, the LED driver modules prevent the glare of light due to voltage variation.



    2. If malfunctions occur in the LED headlight system, an LED driver module transmits fail signals to the main body ECU. When the main body ECU receives fail signals, it transmits signals to the combination meter, warning the driver.


      Y115003E01



  2. Automatic Headlight Beam Level Control System



    1. The rear height sensor sub-assembly RH detects a change in height of the rear shaft in response to the weight applied to the rear of the vehicle when the vehicle is stopped, and sends the change amount signal to the headlight leveling ECU. The headlight leveling ECU calculates the vehicle posture based on the change amount and controls the headlight beam level by operating the headlight leveling motor.


      Y103024E01

  3. Automatic Light Control System

    1. The main body ECU illuminates or turns off the headlights and taillights at the same time according to the signal from the automatic light control sensor when the power switch is on and the light control switch is in AUTO.

  4. Light Auto Turn-OFF System

    1. While only the taillights are illuminated, the main body ECU turns off all of the exterior lights if the driver's door is opened after the power switch is turned off.

    2. When the headlights are illuminated, the main body ECU turns off all of the exterior lights after approximately 30 seconds have elapsed since any door was opened and then closed after the power switch was turned off.

    3. The main body ECU turns off all of the exterior lights if the door is locked using a wireless or smart system when the power switch was turned off with the headlights still turned on.

      HINT:
      These function settings can be changed using the customized body electronics system. For details, refer to the Repair Manual.

  5. Daytime Running Light System

    1. If the READY signal is output from the power management control ECU to the main body ECU when the light control switch and the parking brake pedal are both off, the main body ECU activates the DLR relay and illuminates and fades the headlight high beam*1 or daytime running light*2.

      1. *1: Models for Canada
      2. *2: Except models for Canada


CONSTRUCTION


  1. LED Headlight System



    1. The LED headlight system is used for the low beams, and this consists of the 2 projector type LED lights.


      Y115004E01



    2. The light from the 2 projector type LED lights are reflected by the reflector and passes through the projector, illuminating an area in the distance. At this time, the illuminated area is optimized by the shape of the reflectors and projector.


      Y115005E01


      Text in Illustration 
      *1
      Headlight Assembly
      *2
      Reflector
      *3
      LED
      -
      -
      *a
      A-A Cross Section
      -
      -



  2. LED Driver Module



    1. The LED driver modules are placed beneath the headlights, and this supplies a constant voltage to the low beams and reduces the changes in the energization current.


      Y115246E01


      Text in Illustration 
      *1
      LED driver Module
      -
      -



  3. Stop Light Switch

    1. The stop light switch contains a shaft, magnet, 2 magnet sensors and a circuit plate. The magnet is attached to the shaft.
    2. When the brake pedal is depressed, the stop light switch shaft and magnet move at the same time. The magnet sensors on the circuit plate detect the extent of the magnet movement and output it in the form of on/off signals. One of the 2 magnet sensors is used for the stop light illumination signal, and the other for the cruise control cancel signal.

      NOTICE:
      Do not place magnets or magnetized objects close to the stop light switch. Placing magnets or magnetized objects close to the stop light switch may adversely affect the characteristics of the switch.


    Y103721E01


FAIL-SAFE
  1. LED Headlight System

    1. The LED driver module executes the fail-safe actions listed below in accordance with the problem that has been detected.

      Problem
      Outline
      Detection of Abnormal Output (Open Circuit or Short Circuit)
      If an abnormal condition (open or short) occurs in the voltage that is output by LED driver module, the LED driver module stops illuminating the headlights and will maintain this state until the power is reinstated. Power is reinstated by turning the light control switch from OFF to ON.
      Detection of Abnormal Input Voltage
      If the voltage that is input to LED driver module deviates from the normal operating voltage (10 - 16 volts), the LED driver module stops illuminating the headlights. It resumes illuminating the headlights once the voltage reverts to the operating voltage range.

  2. Automatic Headlight Beam Level Control System

    1. If an abnormal condition such as those listed below has been detected, the headlight leveling ECU operates in the fail-safe mode. The headlight leveling ECU illuminates the headlight leveling indicator light in the combination meter when the height control sensor abnormality has been detected.

      Problem
      Outline
      Power Supply Voltage Malfunction
      Holds the beam at the position of the headlight leveling motor when the abnormality has been detected.
      Rear Height Control Sensor Sub-assembly Power Supply Malfunction
      Rear Height Control Sensor Sub-assembly Signal Malfunction

  3. Automatic Light Control System

    1. When the main body ECU detects a malfunction in the automatic light control sensor, it prohibits the control, however, the system maintains the current illumination state until the light control switch is turned to any positions other than AUTO or the power switch is turned off.

      Problem
      Outline
      Automatic Light Control Sensor Input Frequency Malfunction
      Determines that there is a malfunction in the automatic light control sensor if the output frequency from the automatic light control sensor lowers below a specified value when the automatic light control sensor power supply is turned on, and stops the control.

  4. Daytime Running Light System

    1. The daytime running light system turns off the daytime running lights to protect the inside circuits if a malfunction occurs in the circuits and a load is applied to the running light relay.

      Problem
      Outline
      Running Light Relay Overheated
      Turns off whichever daytime running light which is overloaded. (even if the light is dimmed.)
      Headlight High Beam Illumination Request and Daytime Running Light Illumination Request Overlapped*
      Prioritizes turning on the headlight high beams.

      1. *: Models for Canada


DIAGNOSIS
  1. LED Headlight System

    1. If the main body ECU detects a malfunction in the LED headlight system, the main body ECU flashes the master warning light and indicates the warning message on the multi-information display. At the same time, the Diagnostic Trouble Code (DTC) is stored in memory. The DTC can be read using the Techstream. For details, refer to the Repair Manual.

  2. Automatic Headlight Beam Level Control System

    1. When the headlight leveling ECU detects malfunctions in the automatic headlight beam level control system, DTCs are stored in memory.

    2. The DTCs can be read using the Techstream. For details, refer to the Repair Manual.

  3. Automatic Light Control System

    1. When the main body ECU detects malfunctions in the automatic light control system, DTCs are stored in memory.

    2. The DTCs can be read using the Techstream. For details, refer to the Repair Manual.