LANE-KEEPING ASSIST SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components in the lane-keeping assist system have the following functions:

    Component
    Function
    Lane Recognition Camera Sensor
    Captures the road scene ahead of the vehicle, detects lane markers on the driving lane, and calculates the deviation from the center of the lane, yaw rate and radius of the curve.
    LKA Main Switch
    Sends the on/off state to the driving support ECU.
    Driving Support ECU
    1. Controls the amount of steering assist in accordance with signals from switches and ECUs.
    2. Transmits the indicator light illumination request signal, multi-information display indication request signal, and buzzer sound request signal to the combination meter assembly.
    3. Sends a buzzer sound request signal to the skid control buzzer.
    Skid Control ECU
    1. Sends the vehicle speed signal from the speed sensor to the driving support ECU.
    2. Sounds the skid control buzzer in accordance with a request signal from the driving support ECU.
    Power Steering ECU
    1. Controls the power steering motor in accordance with signals from the driving support ECU.
    2. Transmits the driver's steering input signal to the driving support ECU.
    Combination Meter Assembly
    LKA Indicator Light
    Illuminates or blinks to warn the driver in accordance with signals from the driving support ECU.
    Multi-information Display
    Displays a message to inform or warn the driver of the system condition in accordance with signals from the driving support ECU.
    Master Warning Light
    Illuminates to warn the driver in accordance with signals from the driving support ECU.
    Buzzer
    Sounds to warn the driver in accordance with signals from the driving support ECU.
    Steering Column Assembly
    Power Steering Motor
    Applies a steering assist force.
    Torque Sensor
    Detects the driver's steering input and transmits it to the power steering ECU.
    Skid Control Buzzer
    Sounds to warn the driver in accordance with signals from the skid control ECU.
    Millimeter Wave Radar Sensor
    Detects the vehicle ahead and transmits the distance to the vehicle ahead to the driving support ECU.
    Yaw Rate and Acceleration Sensor
    Detects yaw rate and transmits a signal to the driving support ECU.
    Speed Sensor
    Transmits the vehicle speed signal to the skid control ECU.
    Cruise Control Main Switch
    Transmits the cruise control main switch signal to the driving support ECU.
    Stop Light Switch
    Detects the depressing of the brake pedal and transmits a signal to the driving support ECU.
    Windshield Wiper Switch
    Transmits windshield wiper switch signal to the driving support ECU.
    Turn Signal Switch
    Transmits turn signal command to the driving support ECU.


OPERATING CONDITION
  1. Operating Conditions

    1. The lane-keeping assist system can be activated by pressing the LKA main switch. At this time, the LKA indicator light in the combination meter assembly illuminates.

    2. The operating conditions of the lane-keeping assist system lane departure warning function and lane-keeping assist function differ in accordance with the on/off status of the dynamic radar cruise control system and the vehicle speed.

      LKA Main Switch
      Dynamic Radar Cruise Control System
      Vehicle Speed
      Function
      ON
      OFF
      Approximately 48 km/h (30 mph) or higher
      Lane Departure Warning
      ON
      Approximately 48 to 72 km/h (30 to 45 mph)
      Lane Departure Warning
      Approximately 72 to 180 km/h (45 to 112 mph)
      Lane-keeping Assist
      Approximately 180 km/h (112 mph)
      Lane Departure Warning

  2. Suspension Conditions

    1. The lane departure warning function and the lane-keeping assist function suspension condition are as follows. However, if it is confirmed that the suspension conditions are cancelled, the system will be reactivated.

      Lane Departure Warning Function 
      When the vehicle speed is approximately 48 km/h (30 mph) or below.
      The turn signal command is detected.
      The steering force input is above a certain level.
      The windshield wiper switch position is high or low.
      No lane markers are detected.
      The stop light switch signal is detected.
      Immediately after the lane departure warning is activated. However, if a few seconds has elapsed and it is confirmed that the vehicle is running inside lane markers, the system will be reactivated.

      Lane-keeping Assist Function 
      When the vehicle speed is approximately 72 km/h (45 mph) or below, or approximately 180 km/h (112mph) or higher.
      The turn signal command is detected.
      The steering force input is above a certain level.
      The windshield wiper switch position is high or low.
      No lane markers are detected.
      More than approximately half of the vehicle is judged to have crossed a lane marker.
      No steering force is detected for certain period of time.

  3. Stop conditions

    1. The lane departure warning function and the lane-keeping assist function stop and restart conditions are as follows.

      Lane Departure Warning Function 
      Stop Condition
      Restart Condition
      The LKA main switch is turned off.
      The LKA main switch is turned on.
      The system is temporarily stopped.
      If the LKA main switch is in on state, the system will be automatically reactivated after the temporarily stop is cancelled.

      Lane-keeping Assist Function 
      Stop Condition
      Restart Condition
      The LKA main switch is turned off.
      The LKA main switch is turned on.
      Dynamic radar cruise control system is cancelled.*
      Dynamic radar cruise control system is turned on again.
      The brake is operated.*
      Dynamic radar cruise control system is turned on again.
      The system is temporarily stopped.
      If the LKA main switch is in on state, the system will be automatically reactivated after the temporarily stop is cancelled.

      HINT:
      *: Automatically switches to the lane departure warning function.


SYSTEM CONTROL
  1. Function List

    1. The lane-keeping assist system has following functions:

      Function
      Outline
      Lane Departure Warning
      When the system determines that the vehicle is about to deviate from its lane, the system urges the driver to correct the lane deviation by displaying a warning message, sounding the buzzer and applying a small amount of steering force.
      Lane-keeping Assist
      When cruise control is in operation, the system applies a small amount of steering force using EPS to assist driver's steering operation.



  2. Lane Departure Warning Function

    1. The driving support ECU calculates the estimated position which the front wheel will reach after approximately 1 second based on the information collected by the lane recognition camera sensor, vehicle speeds and front wheel positions. When the driving support ECU determines that the front wheel is about to cross the lane marker, the driving support ECU activates the lane departure warning function, displays a warning message on the multi-information display, sounds the skid control buzzer, and applies a small amount of steering force by activating the power steering motor for approximately 1 second to urge the driver to correct the steering.



    2. The lane departure warning function does not operate if the vehicle approaches the lane marker (but does not cross it), as long as the vehicle remains parallel with the lane marker.


      Y102773E01



  3. Lane-keeping Assist Function

    1. The driving support ECU activates the power steering motor via the power steering ECU based on the road information collected by the lane recognition camera sensor and assists in the driver's steering operation to keep the vehicle near the center of the lane.

    2. The driving support ECU constantly calculates and controls the steering assist force in accordance with the radius of the curve on the lane, heading angle deviation and lateral deviation from the center of the lane.

    3. If the driving support ECU determines that the vehicle is deviating from the lane, the skid control ECU sounds the skid control buzzer. At this time, the driving support ECU displays a warning message on the multi-information display to warn the driver of lane deviation.

    4. If the driver's steering input is not detected for a certain period, the driving support ECU alerts the driver by sounding the buzzer in the combination meter assembly and by displaying a message on the multi-information display.



    5. The lane-keeping assist function is activated when the LKA main switch is turned on while the steering wheel icon is indicated on the multi-information display. If the icon is not displayed, the function is not activated when the LKA main switch is turned on.


      Y102774E01


FUNCTION
  1. Combination Meter Assembly

    1. The combination meter assembly provides a master warning light, LKA indicator light, buzzer, and multi-information display to warn and indicate in the lane-keeping assist system in accordance with function. In addition, the skid control buzzer will sound when the warning is operated.

    2. The multi-information display displays the lane departure warning function, lane-keeping assist function, and warning message. However, during the operation of each function, the lane marker icons will be displayed in bold.

      Lane Departure Warning Function 
      Condition
      Dynamic Radar Cruise Control System
      Multi-information Display
      Y102031
      Buzzer*
      Skid Control Buzzer
      Function in Operation
      OFF
      Y102778
      Illuminates
      -
      -
      ON
      Y102779
      Illuminates
      -
      -
      Warning Operating
      OFF
      Y102780
      Illuminates
      -
      Sounds Continuously
      Lane Marker Not Detected
      OFF
      Y102781
      Illuminates
      Sounds for 1 to 2 seconds
      -
      ON
      Y102782
      Illuminates
      Sounds for 1 to 2 seconds
      -

      HINT:
      *: Indicates the buzzer on the combination meter assembly.


      Lane-keeping Assist Function 
      Condition
      Multi-information Display*1
      Y102031
      Buzzer*2
      Skid Control Buzzer
      Function in Operation
      Y103261
      Illuminates
      -
      -
      1. Warning Operating
        1. Lane deviation
      Y103262
      Illuminates
      -
      Sounds Continuously
      1. Warning Operating
        1. Hands not contacting steering wheel
      Illuminates
      Sounds for 1 to 2 seconds
      -
      Lane Marker Not Detected
      Y103263
      Illuminates
      Sounds for 1 to 2 seconds
      -

      HINT:
      *1: When the lane-keeping assist function is operating, a steering wheel icon will be displayed on the multi-information display in the combination meter assembly.
      *2: Indicates the buzzer on the combination meter assembly.


      Warning Massage 
      Condition
      Multi-information Display
      Y102031
      Y100442
      Buzzer
      1. Temperature of Lane Recognition Camera Sensor is Abnormal.
      2. EPS System is Malfunctioning or Abnormal.
      Y103264
      Illuminates
      -
      -
      System Malfunction
      Y103265
      Blinks
      Illuminates
      Sounds
      Lane Recognition Camera Sensor Angle Adjustment
      Y103266
      Blinks
      -
      -


CONSTRUCTION


  1. Lane Recognition Camera Sensor



    1. A lane recognition camera sensor is mounted at the top center portion of the top part of the windshield glass and is used for the lane-keeping assist system.


      Y102775

      HINT:
      When one of the following operations is conducted, the lane recognition camera sensor angle must be adjusted.
      1. The lane recognition camera sensor is removed and reinstalled or replaced.
      2. Parts relating to the suspension are adjusted or replaced.
      For details, refer to the Repair Manual.



    2. The lane recognition camera sensor captures the road image up to approximately 30 m (98 ft.) ahead of the vehicle. In addition, detectable lane width is approximately 3 to 4 m (9 to 13 ft.).


      Y102776E01


      Text in Illustration 
      *1
      Lane Recognition Camera Sensor
      -
      -
      *a
      Lane Marker
      *b
      Approximately 30 m
      *c
      Approximately 3 m to 4 m
      -
      -
      V100144
      Image Processing Range
      -
      -



    3. By processing the road image data, the lane recognition camera sensor detects lane marker and calculates the radius to the center of the lane, heading angle deviation, lateral deviation from the center of the lane, and the lane width.


      Y102777E01


      Text in Illustration 
      *a
      Image Captured by Lane Recognition Camera Sensor
      *b
      Center of Lane
      *c
      Left Lane Marker
      *d
      Right Lane Marker
      *e
      Radius to Center of Lane
      *f
      Lane Width
      *g
      Lateral Deviation
      *h
      Heading Angle Deviation


DIAGNOSIS
  1. If a malfunction is detected in the lane-keeping assist system, the driving support ECU stops the system, blinks the LKA indicator light, illuminates the master warning light, sounds the buzzer, and outputs a warning message on the multi-information display to inform the driver of the malfunction. At the same time, the malfunction is stored in memory as a Diagnostic Trouble Code (DTC).

  2. When the Techstream is connected to the DLC3, the DTC can be read. For details, refer to the Repair Manual.