SAFETY CONNECT SYSTEM > DETAILS |
| FUNCTION OF MAIN COMPONENTS |
The main components in the safety connect have the following functions:
| Component | Function | ||
| Map Light Assembly | Manual (SOS) Switch | Pressing the manual (SOS) switch allows the driver to reach and communicate with the call center as an emergency assistance button (SOS) service or Roadside Assistance service. | |
| Telephone Microphone Assembly | The user's voice is received by the microphone module. | ||
| Manual (SOS) Switch Indicator | Green | The manual (SOS) switch indicator illuminates, blinks or turns off depending on the conditions when the Safety Connect is activated, operating, malfunctioning, during a call with the call center or the modes it is in. | |
| Red | |||
| DCM (Telematics Transceiver) |
| ||
| BUB |
| ||
| Telephone and GPS Antenna | Telephone Antenna | This antenna is for a cellular phone. It is compatible with the transmission and reception of frequency bands of cellular phones. Transmits signals from the DCM (Telematics Transceiver) and receives signals from the call center. | |
| GPS Antenna | Receives the signals from the GPS satellites and transmits these signals to the DCM (Telematics Transceiver). | ||
| Stereo Component Amplifier Assembly | Receives the mute signal from the DCM (Telematics Transceiver) to mutes any audio sound. | ||
| Front Squawker RH | Outputs the call center advisor's voice. | ||
| Navigation Receiver Assembly | Receives microphone voice signals from DCM (Telematics Transceiver). | ||
| Airbag ECU Assembly | Sends an airbag deployment or collision detection signal to the DCM (Telematics Transceiver). | ||
| Instrument Panel Junction Block Assembly | Sends the taillight relay on signal to the DCM (Telematics Transceiver). | ||
| FUNCTION |
Automatic Collision Notification Service
In the event of an accident in which any of the airbags is deployed or a severe collision occurs, upon receiving a deployment signal from the airbag ECU assembly, the DCM (Telematics Transceiver) automatically makes an emergency call and transmits the vehicle position and user information to the call center. Then, the line will be automatically connected to the call center and the driver can speak with the call center advisor. If the driver is unable to communicate, the call center advisor will alert the PSAP nearest to the vehicle, explain the situation, and request dispatching emergency services.

| *a | Airbag Deployment or Collision Detection | *b | Call Center |
| *c | 911 Emergency Services | *d | Ambulance |
Emergency Assistance Button (SOS) Service
When the manual (SOS) switch is used in an emergency on a road, a call center advisor will locate the vehicle position, judge the level of an emergency, and then offer emergency services such as PSAP appropriate to the situation.

| *1 | Manual (SOS) Switch | - | - |
| *a | Call Center | *b | 911 Emergency Services |
Stolen Vehicle Location Service
In the event of a vehicle theft, the user has to alert the police and then calls the call center. A call center advisor will connect to the stolen vehicle and track the vehicle based on the current vehicle location and speed obtained by the GPS. The call center advisor will also alert the police where required.

| *a | Vehicle Stolen | *b | Call Center |
| *c | 911 Emergency Services | *d | Police |
| *e | Track the Stolen Vehicle | *f | Alert |
Roadside Assistance Service
Pressing the manual (SOS) switch will contact the call center, and a wide range of help, such as towing, flat tire, fuel delivery, etc, can be provided.

| *1 | Manual (SOS) Switch | - | - |
| *a | Call Center | *b | Roadside Assistance Service |
Safety Connect Mode
There are 3 modes depending on the subscription status and the services vary depending on the mode accordingly
| Subscription Status | Mode Type | Available Services |
| Before Subscription | Shipping Mode*1 | ACN Service |
| Stolen Vehicle Location Service | ||
| After Subscription*2 | Active Mode | ACN Service |
| Stolen Vehicle Location Service | ||
| Emergency Assistance Button (SOS) Service | ||
| Roadside Assistance Service | ||
| After Subscription cancellation*3 | Deactive Mode | - |
Voice Guidance Function
The following voice messages are played depending on the situation.
| Voice Prompt | Usage Condition |
| "Safety Connect failure detected, please contact your dealer". | When the system detects manual (SOS) switch red indicator failure. The system repeats this warning once each time the power switch is turned on (IG) until the problem is fixed. |
| "Connecting to the Call Center". | Active mode |
| "Safety Connect Activation Failed". | Deactive mode |
| "Safety Connect Activation Complete". | The DCM (Telematics Transceiver) activation completes normally. |
| "Please make sure you are in an area with good cellular coverage and try again. If you continue to receive this message, contact your dealer". | Follows port activation sequence. |
| "Unable to Connect to the Call Center". | The DCM (Telematics Transceiver) cannot connect, such as retries are exceeded, or center is unavailable. |
| "Impact Detected". | When the DCM (Telematics Transceiver) received an collision detection signal. |
| "Connecting to the Emergency Call Center". | Call initiated to call center. |
| "Unable to Connect to the Emergency Call Center". | The DCM (Telematics Transceiver) cannot connect to emergency call center for some reason. |
| "To cancel, please press the button again". | If we can cancel emergency call. |
| "Emergency call cancelled". | If we can cancel emergency call. |
| "The system will try again". | The DCM (Telematics Transceiver) cannot connect to emergency call center for some reason. |
| "Welcome to Safety Connect". | This voice prompt is a short version for activation. |
| "To activate, please press the button again within 5 seconds". | This voice prompt is an instruction for activation. |
| "Safety Connect is not initialized". | Reserve for activation. |
| "Safety Connect is not active". | When the DCM (Telematics Transceiver) is in Deactive mode. |
| "For information on setting up a new subscription or to initialize a subscription you've already set up, please press the button again within 5 seconds". | When the DCM (Telematics Transceiver) is in Deactive mode. |
| CONSTRUCTION |
Manual (SOS) Switch Indicator
When the power switch is turned on (IG), the manual (SOS) switch red indicator illuminates for 2 seconds and turns off. Then, the manual (SOS) switch green indicator illuminates for 2 seconds. The manual (SOS) switch indicator illuminates, blinks or turns off depending on the mode type.
When the power switch is turned off, the manual (SOS) switch red indicator and manual (SOS) switch green indicator turn off. If a call is in progress when the power switch is turned off, the call and indicators will continue to function.

| *1 | Manual (SOS) Switch Green Indicator | *2 | Manual (SOS) Switch Red Indicator |
Indicators shown in each mode are as follows:
| Mode Type | Manual (SOS) Switch Indicator | |
| Green | Red | |
| Shipping Mode | Blinks together with the manual (SOS) switch red indicator for approximately 20 seconds at 1 second intervals. |
|
| Active Mode |
| Illuminates when the DCM (Telematics Transceiver) has stored DTCs. |
| Deactive Mode | Remains turned off. | Illuminates when the DCM (Telematics Transceiver) has stored DTCs. |
| DIAGNOSIS |