Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER

FRONT SHOCK ABSORBER > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the LH side.



1. REMOVE FRONT WHEEL


2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:
Refer to the procedure up to Remove Windshield Wiper Motor and Link Assembly .



3. REMOVE COWL BODY MOUNTING REINFORCEMENT LH


    C205667
  1. Remove the 3 bolts and cowl body mounting reinforcement LH.



4. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C205668E01
  1. Disengage the 2 clamps and guide of the wire harness.
    Text in Illustration 
    *1
    Clamp
    *2
    Guide



    C205670
  1. Disengage the claw and bend the No. 1 heater air duct splash shield seal.



    C205672
  1. Disengage the claw and bend the water guard plate RH.



    C205669
  1. Remove the 9 bolts and outer cowl top panel sub-assembly.



5. SEPARATE FRONT STABILIZER LINK ASSEMBLY


    C205585
  1. Remove the nut and separate the stabilizer link assembly from the front shock absorber with coil spring.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



6. SEPARATE FRONT SPEED SENSOR


    C208843
  1. Remove the bolt and clamp, and separate the front speed sensor and front flexible hose from the front shock absorber with coil spring.

    NOTICE:
    Be sure to separate the front speed sensor from the front shock absorber with coil spring completely.



7. REMOVE FRONT SUSPENSION SUPPORT DUST COVER


    C205588
  1. Remove the front suspension support dust cover.



8. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


    C205589
  1. Loosen the front support to front shock absorber nut of the front shock absorber.

    NOTICE:
    1. Do not remove the front support to front shock absorber nut.
    2. Loosen the nut only when the front shock absorber with coil spring needs to be disassembled.



    C207008E01
  1. Support the front axle using a jack and wooden block.
    Text in Illustration 
    *1
    Wooden Block



    C205584
  1. Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.



    C205591
  1. Remove the 3 nuts and front shock absorber with coil spring.

    NOTICE:
    Make sure that the front speed sensor is completely separated from the front shock absorber with coil spring.



9. SECURE FRONT SHOCK ABSORBER WITH COIL SPRING


    C205592E01
  1. Install a bolt and nut to the front shock absorber as shown in the illustration and secure the front shock absorber in a vise.

    Standard length A:
    40 mm (1.575 in.)



10. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    C205593E01
  1. Using SST, compress the front coil spring.

    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)

    NOTICE:
    Do not use an impact wrench. It will damage SST.

    HINT:
    If the front coil spring is compressed at an angle, using 2 SST will make the work easier.

  1. Check that the front coil spring is sufficiently compressed.



    C206987
  1. Remove the front support to front shock absorber nut and collar.



11. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY


12. REMOVE STRUT MOUNTING BEARING


13. REMOVE FRONT COIL SPRING UPPER SEAT


14. REMOVE FRONT COIL SPRING UPPER INSULATOR


15. REMOVE FRONT COIL SPRING


16. REMOVE FRONT SPRING BUMPER


17. REMOVE FRONT COIL SPRING LOWER INSULATOR


18. REMOVE FRONT SHOCK ABSORBER ASSEMBLY