FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY |
| 1. REMOVE SEAT ADJUSTER COVER CAP |
![]() |
Remove the seat adjuster cover cap.
| 2. REMOVE RECLINING ADJUSTER RELEASE HANDLE |
![]() |
Using a screwdriver wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.
| *1 | Protective Tape |
| 3. REMOVE VERTICAL ADJUSTING HANDLE (for Driver Side) |
![]() |
Remove the screw and vertical adjusting handle.
| 4. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY |
![]() |
Remove the screw.
Disengage the 6 claws and clip, and remove the front seat cushion shield.
| 5. REMOVE FRONT SEAT INNER BELT ASSEMBLY |
Disconnect each connector.
Disengage each clamp.
![]() |
Remove the nut and front seat inner belt assembly.
| 6. REMOVE FRONT INNER SEAT CUSHION SHIELD |
![]() |
Disengage the 5 claws and remove the front inner seat cushion shield.
| 7. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD |
![]() |
Disconnect the rubber band.
![]() |
Disengage the 4 hooks.
w/ Seat Heater System:
![]() |
Disengage the 4 clamps and disconnect the seat heater wire harness.
![]() |
Disconnect the connector.
Disengage the clamp and disconnect the seat heater wire harness.
![]() |
Disengage the fastener and disconnect the side airbag wire harness.
for Front Passenger Side:
![]() |
Disengage the hook and disconnect the belt warning occupant detection sensor.
![]() |
Disengage the 2 hooks as shown in the illustration.
Disengage each hook and remove the separate type front seat cushion cover with pad from the front seat cushion spring sub-assembly as shown in the illustration.

| 8. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Remove the 2 hog rings.
![]() |
Remove the 11 hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.
| 9. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD |
![]() |
Remove the 2 hog rings.
![]() |
Remove the 3 hog rings.
![]() |
Pull out the lower part of 2 fasteners from the separate type front seatback cover as shown in the illustration.
![]() |
Open the 2 fasteners.
![]() |
Remove the 3 hog rings and disconnect the 2 fastening rubbers.
| *1 | Fastening Rubber |
![]() |
Disengage the 2 hooks.
![]() |
Turn back the separate type front seatback cover and remove the nut, and remove the bracket of the separate type front seatback cover.
![]() |
Disengage the 4 claws and remove the 2 front seat headrest supports.
Remove the separate type front seatback cover with pad from the separate type front seatback spring sub-assembly.
| 10. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Remove the 5 hog rings.
![]() |
Remove the 2 hog rings and the separate type front seatback cover from the separate type front seatback pad.
| 11. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Disengage the guide and remove the reclining adjuster inside cover LH.
| 12. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
| 13. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side) |
![]() |
Disengage the hook as shown in the illustration.
![]() |
Remove the screw.
Disengage the clip and remove the front seat lower cushion shield LH.
| 14. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side) |
| 15. REMOVE NO. 2 FRONT SEAT CUSHION PROTECTOR |
![]() |
Remove the screw.
Disengage the 2 guides and remove the No. 2 front seat cushion protector.
| 16. REMOVE NO. 1 FRONT SEAT CUSHION PROTECTOR |
| 17. REMOVE FRONT SEAT CUSHION COVER RH (for Front Passenger Side) |
![]() |
Using a clip remover, remove the clip.
![]() |
Remove the front seat cushion cover RH from the occupant classification ECU as shown in the illustration.
| 18. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
![]() |
Disconnect the 2 connectors.
Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the occupant classification ECU.
| *1 | Protective Tape |
| 19. REMOVE SEAT POSITION SENSOR |
![]() |
Disconnect the connector.
Separate the wire harness from the seat slide position sensor protector.
Using a T30 "TORX" socket wrench, remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.
![]() |
Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.
| 20. REMOVE FRONT SEAT WIRE RH (for Front Passenger Side) |
![]() |
Disconnect the 4 connectors.
Disengage the 7 clamps and remove the front seat wire RH from the front seat cushion spring assembly.
| 21. REMOVE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY |
![]() |
Remove the 4 bolts and separate type front seatback spring assembly from the separate type front seat cushion spring assembly.
| 22. REMOVE SEAT TRACK ADJUSTING HANDLE |
![]() |
Disengage the 2 hooks and remove the seat track adjusting handle from the separate type front seat cushion spring assembly.
| 23. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY |
![]() |
Disengage the 2 clamps.
Remove the 2 nuts and the front seat side airbag assembly.