Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.



2. INSTALL SEAT TRACK ADJUSTING HANDLE


    B256057
  1. Engage the 2 hooks to install the seat track adjusting handle to the separate type front seat cushion spring assembly.



3. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY


    B229882
  1. Install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)


    B284759
  1. Engage the 7 clamps to install the front seat wire RH.

  1. Connect the 4 connectors.



5. INSTALL SEAT POSITION SENSOR


    B228032
  1. Install the seat position sensor to the seat slide position sensor protector with the pin as shown in the illustration.



    C107067E12
  1. Using a 1.3 mm (0.0512 in.) feeler gauge, temporarily install the seat position sensor with the "TORX" screw.
    Text in Illustration 
    *1
    Seat Position Sensor
    *2
    Feeler Gauge
    *3
    Seat Rail

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with or is pinched between other parts.



    B228030
  1. Using a T30 "TORX" socket wrench, tighten the "TORX" screw.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and seat rail is 1.3 mm (0.0512 in.).

  1. Install the wire harness to the seat slide position sensor protector.

  1. Connect the connector.

  1. Check that there is no looseness in the installation parts of the seat position sensor.



6. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


    B228034
  1. Install the occupant classification ECU with the claw.

    NOTICE:
    If the occupant classification ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the occupant classification ECU with a new one.

  1. Connect the 2 connectors.

    NOTICE:
    When installing the occupant classification ECU, be careful that the SRS wiring does not interfere with or is pinched between other parts.



7. INSTALL FRONT SEAT CUSHION COVER RH (for Front Passenger Side)


    B299253
  1. Install the front seat cushion cover RH to the occupant classification ECU as shown in the illustration.



    B299251
  1. Install the clip.



8. INSTALL NO. 2 FRONT SEAT CUSHION PROTECTOR


    B284868
  1. Engage the 2 guides and install the No. 2 front seat cushion protector with the screw.



9. INSTALL NO. 1 FRONT SEAT CUSHION PROTECTOR

HINT:
Use the same procedure as for the No. 2 front seat cushion protector.



10. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)


    B229873
  1. Engage the clip to temporarily install the front seat lower cushion shield LH with the screw.



    B284862
  1. Engage the hook to install the front seat lower cushion shield LH as shown in the illustration.



11. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)

HINT:
Use the same procedure as for the LH side.



12. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B284866
  1. Engage the guide and install the reclining adjuster inside cover LH.



13. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure as for the LH side.



14. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B277150E01
  1. Using hog ring pliers, connect the fastening rubber to the separate type front seatback pad with 2 new hog rings.
    Text in Illustration 
    *1
    Fastening Rubber
    *2
    Hog Ring

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B229858
  1. Using hog ring pliers, install the separate type front seatback cover with 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



15. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
  1. Temporarily install the separate type front seatback cover with pad to the front seatback spring sub-assembly.



    B229856
  1. Engage the 4 claws to install the 2 front seat headrest supports.



    B301044
  1. Install the front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
    2. Check that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B301043
  1. Engage the 2 hooks.



    B229852E01
  1. Using hog ring pliers, connect the fastening rubber to the separate type front seatback spring assembly with 3 new hog rings.
    Text in Illustration 
    *1
    Fastening Rubber
    *2
    Hog Ring

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B299241
  1. Close the 2 fasteners.



    B299237
  1. Push in the lower part of 2 fasteners to the separate type front seatback cover as shown in the illustration.



    B299233
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B299229
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B229847
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 11 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



    B232926
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



17. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


  1. Engage each hook to install the separate type front seat cushion cover with pad to the front seat cushion spring sub-assembly as shown in the illustration.


    B229839



    B229843
  1. Engage the 2 hooks as shown in the illustration.



  1. for Passenger Side:



      B229825
    1. Engage the hook to connect the belt warning occupant detection sensor.



    B301041
  1. Engage the fastener to connect the side airbag wire harness.



  1. w/ Seat Heater System:



      B301040
    1. Engage the clamp to connect the seat heater wire harness.

    2. Connect the connector.



    3. B299259
    4. Engage the 4 clamps to connect the seat heater wire harness.



    B229834
  1. Engage the 4 hooks.



    B252715
  1. Connect the rubber band.



18. INSTALL FRONT INNER SEAT CUSHION SHIELD


    B284789
  1. Engage the 5 claws to install the front inner seat cushion shield.



19. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    B226478E01
  1. Install the front seat inner belt assembly with the nut.
    Text in Illustration 
    *1
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect each connector.

  1. Engage each clamp.



20. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY


    B284787
  1. Engage the clip and 6 claws to install the front seat cushion shield.

  1. Install the screw.



21. INSTALL VERTICAL ADJUSTING HANDLE (for Driver Side)


    B252541
  1. Install the vertical adjusting handle with the screw.



22. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B252540
  1. Engage the claw and install the reclining adjuster release handle.



23. INSTALL SEAT ADJUSTER COVER CAP


    B270241
  1. Install the seat adjuster cover cap.

    HINT:
    Use the same procedure for the RH side and LH side.