Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B231709E13


Text in Illustration 
*A
Main body ECU (multiplex network body ECU) with 3 connectors
-
-
*1
Main body ECU (multiplex network body ECU)
*2
3 connectors
  1. Disconnect the 2A, 2B, 2C, 2E and L8 instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2A-43 - Body ground
    G - Body ground
    ACC power supply
    Power switch on (ACC)
    11 to 14 V
    Power switch off
    Below 1 V
    2B-25 - Body ground
    B - Body ground
    IG power supply
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    2C-18 (BECU) - Body ground
    Y - Body ground
    Battery power supply
    Always
    11 to 14 V
    2E-1 - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-6 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L8-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the 2A, 2B, 2C, 2E and L8 instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.



  5. Measure the voltage or check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-29 (LSR) - Body ground
    GR - Body ground
    Rear door unlock detection switch RH input
    Rear door RH and LH locked
    Pulse generation
    Rear door RH or LH unlocked
    Below 1 V
    2C-20 (PKB) - Body ground
    R - Body ground
    Parking brake switch input
    Parking brake switch on
    Below 1 V
    Parking brake switch off
    11 to 14 V
    2C-22 (DIM) - Body ground
    Y - Body ground
    High beam headlights drive output
    Dimmer switch in high or high flash position
    Below 1 V
    Dimmer switch in low position
    11 to 14 V
    2C-32 (HRLY) - Body ground
    G - Body ground
    Headlight relay drive output
    Light control switch in head position
    Below 1 V
    Light control switch not in head position
    11 to 14 V
    2C-35 (DRL)*1 - Body ground
    L - Body ground
    Daytime running light system drive output
    Daytime running light system operates
    Below 1 V
    Daytime running light system not operates
    11 to 14 V
    2D-25 (LSR) - Body ground
    GR - Body ground
    Rear door unlock detection switch LH input
    Rear door LH and RH locked
    Pulse generation
    Rear door LH and RH unlocked
    Below 1 V
    2D-35 (FLCY) - Body ground
    V - Body ground
    Front door courtesy light switch LH input
    Front door LH open
    Below 1 V
    Front door LH closed
    11 to 14 V
    2D-36 (FRCY) - Body ground
    BR - Body ground
    Front door courtesy light switch RH input
    Front door RH open
    Below 1 V
    Front door RH closed
    11 to 14 V
    L7-6 (LRCY) - Body ground
    G - Body ground
    Rear door courtesy light switch RH or LH input
    Rear door RH or LH open
    Below 1 V
    Rear door RH and LH closed
    Pulse generation
    L7-7 (LSFL) - Body ground
    GR - Body ground
    Front door unlock detection switch LH input
    Front door LH locked
    Pulse generation
    Front door LH unlocked
    Below 1 V
    L7-8 (HF) - Body ground
    LG - Body ground
    Dimmer switch high flash position signal input
    Dimmer switch in high flash position
    Below 1 V
    Dimmer switch not in high flash position
    Pulse generation
    L7-18 (LSFR) - Body ground
    LG - Body ground
    Front door unlock detection RH switch input
    Front door RH locked
    Pulse generation
    Front door RH unlocked
    Below 1 V
    L7-19 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    Back door closed
    11 to 14 V
    L7-20 (CLTB) - Body ground
    R - Body ground
    Automatic light control sensor power supply output
    Power switch off
    Below 1 V
    Power switch on (IG) and light control switch in AUTO position
    11 to 14 V
    L7-21 (CLTS) - Body ground
    W - Body ground
    Automatic light control sensor signal input
    Power switch off
    Below 1 V
    Automatic light control system operates
    Pulse generation
    (See waveform 1)
    L7-27 (FFOG) - Body ground
    LG - Body ground
    Front fog light switch input
    Front fog light switch on
    Below 1 V
    Front fog light switch off
    Pulse generation
    L7-28 (A) - Body ground
    W - Body ground
    Light control switch AUTO position signal input
    Light control switch in AUTO position
    Below 1 V
    Light control switch not in AUTO position
    Pulse generation
    L7-29 (HEAD) - Body ground
    L - Body ground
    Light control switch head position input
    Light control switch in head position
    Below 1 V
    Light control switch not in head position
    Pulse generation
    L7-30 (TAIL) - Body ground
    Y - Body ground
    Light control switch tail position signal input
    Light control switch in tail or head position
    Below 1 V
    Light control switch in neither tail nor head position
    11 to 14 V

    1. *1: w/ Daytime Running Light
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.



      B113714E01
    1. Waveform 1
      Item
      Content
      Tool setting
      5 V/DIV., 5 ms./DIV.

      HINT:
      If the ambient light becomes brighter, width A becomes narrower.


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

E192848E15


Text in Illustration 
*A
Main body ECU (multiplex network body ECU) with 1 connector
-
-
*1
Main body ECU (multiplex network body ECU)
*2
1 connector
  1. Disconnect the 2A, 2B, 2C and 2E instrument panel junction block assembly connectors.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2A-43 - Body ground
    G - Body ground
    ACC power supply
    Power switch on (ACC)
    11 to 14 V
    Power switch off
    Below 1 V
    2B-25 - Body ground
    B - Body ground
    IG power supply
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    2C-18 (BECU) - Body ground
    Y - Body ground
    Battery power supply
    Always
    11 to 14 V
    2E-1 - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-6 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the 2A, 2B, 2C, 2E and L8 instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.



  5. Measure the voltage or check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-29 (LSR) - Body ground
    GR - Body ground
    Rear door unlock detection switch RH input
    Rear door RH and LH locked
    Pulse generation
    Rear door RH or LH unlocked
    Below 1 V
    2C-20 (PKB) - Body ground
    R - Body ground
    Parking brake switch input
    Parking brake switch on
    Below 1 V
    Parking brake switch off
    11 to 14 V
    2C-22 (DIM) - Body ground
    Y - Body ground
    High beam headlights drive output
    Dimmer switch in high or high flash position
    Below 1 V
    Dimmer switch in low position
    11 to 14 V
    2C-32 (HRLY) - Body ground
    G - Body ground
    Headlight relay drive output
    Light control switch in head position
    Below 1 V
    Light control switch not in head position
    11 to 14 V
    2D-25 (LSR) - Body ground
    GR - Body ground
    Rear door unlock detection switch LH input
    Rear door LH and RH locked
    Pulse generation
    Rear door LH and RH unlocked
    Below 1 V
    2D-35 (FLCY) - Body ground
    V - Body ground
    Front door courtesy light switch LH input
    Front door LH open
    Below 1 V
    Front door LH closed
    11 to 14 V
    2D-36 (FRCY) - Body ground
    BR - Body ground
    Front door courtesy light switch RH input
    Front door RH open
    Below 1 V
    Front door RH closed
    11 to 14 V
    L7-6 (LRCY) - Body ground
    G - Body ground
    Rear door courtesy light switch RH or LH input
    Rear door RH or LH open
    Below 1 V
    Rear door RH and LH closed
    Pulse generation
    L7-7 (LSFL) - Body ground
    GR - Body ground
    Front door unlock detection switch LH input
    Front door LH locked
    Pulse generation
    Front door LH unlocked
    Below 1 V
    L7-8 (HF) - Body ground
    LG - Body ground
    Dimmer switch high flash position signal input
    Dimmer switch in high flash position
    Below 1 V
    Dimmer switch not in high flash position
    Pulse generation
    L7-15 (DRLE)*1 - Body ground
    G - Body ground
    Daytime running light system drive output
    Daytime running light system operates
    Below 1 V
    Daytime running light system not operates
    11 to 14 V
    L7-18 (LSFR) - Body ground
    LG - Body ground
    Front door unlock detection RH switch input
    Front door RH locked
    Pulse generation
    Front door RH unlocked
    Below 1 V
    L7-19 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    Back door closed
    11 to 14 V
    L7-20 (CLTB) - Body ground
    R - Body ground
    Automatic light control sensor power supply output
    Power switch off
    Below 1 V
    Power switch on (IG) and light control switch in AUTO position
    11 to 14 V
    L7-21 (CLTS) - Body ground
    W - Body ground
    Automatic light control sensor signal input
    Power switch off
    Below 1 V
    Automatic light control system operates
    Pulse generation
    (See waveform 1)
    L7-27 (FFOG) - Body ground
    LG - Body ground
    Front fog light switch input
    Front fog light switch on
    Below 1 V
    Front fog light switch off
    Pulse generation
    L7-28 (A) - Body ground
    W - Body ground
    Light control switch AUTO position signal input
    Light control switch in AUTO position
    Below 1 V
    Light control switch not in AUTO position
    Pulse generation
    L7-29 (HEAD) - Body ground
    L - Body ground
    Light control switch head position input
    Light control switch in head position
    Below 1 V
    Light control switch not in head position
    Pulse generation
    L7-30 (TAIL) - Body ground
    Y - Body ground
    Light control switch tail position signal input
    Light control switch in tail or head position
    Below 1 V
    Light control switch in neither tail nor head position
    11 to 14 V

    1. *1: w/ Daytime Running Light
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.



      B113714E01
    1. Waveform 1
      Item
      Content
      Tool setting
      5 V/DIV., 5 ms./DIV.

      HINT:
      If the ambient light becomes brighter, width A becomes narrower.


CHECK HEADLIGHT LEVELING ECU ASSEMBLY


  1. Disconnect the A48 headlight leveling ECU assembly connector.


    E101528E11

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A48-1 (IG) - Body ground
    LG - Body ground
    IG power supply
    Power switch off
    Below 1 V
    Power switch on (IG)
    11 to 14 V

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A48-9 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the A48 headlight leveling ECU assembly connector.



  4. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A48-21 (SGR) - Body ground
    Y - Body ground
    Rear height control sensor ground
    Always
    Below 1 Ω
    A48-23 (RH-) - Body ground
    BR - Body ground
    Leveling motor RH ground
    Always
    Below 1 Ω
    A48-24 (LH-) - Body ground
    LG - Body ground
    Leveling motor LH ground
    Always
    Below 1 Ω

    Standard Voltage 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A48-3 (HDLP) - Body ground
    V - Body ground
    Low beam headlight signal input
    Low beam headlights on
    Below 1.5 V
    Low beam headlights off
    Above 5 V
    A48-5 (INIT) - Body ground
    B - Body ground
    Initialization signal input
    Terminals LVL and GND of DLC3 connected
    Below 1 V
    Terminals LVL and GND of DLC3 not connected
    Approx. 5 V
    A48-6 (WNG) - Body ground
    L - Body ground
    Warning indicator drive output
    Warning indicator on
    Below 1 V
    Warning indicator off
    11 to 14 V
    A48-10 (RH+) - Body ground
    W - Body ground
    Leveling motor RH power supply
    Power switch off
    Below 1 V
    Power switch on (IG)
    11 to 14 V
    A48-11 (LH+) - Body ground
    R - Body ground
    Leveling motor LH power supply
    Power switch off
    Below 1 V
    Power switch on (IG)
    11 to 14 V
    A48-12 (SBR) - Body ground
    P - Body ground
    Rear height control sensor power supply
    Power switch off
    Below 1 V
    Power switch on (IG)
    4.75 to 5.25 V
    A48-16 (SPDR) - Body ground
    V - Body ground
    Vehicle speed signal input
    Vehicle is driven at approx. 20 km/h (12mph)
    Pulse generation
    (See waveform 1)
    A48-17 (RHT) - Body ground
    B - Body ground
    Leveling motor RH operation signal input
    With low beam headlights on, vehicle height not changed
    Below 1 V
    With low beam headlights on, change vehicle height and keep for more than 3 seconds
    1.0 to 14.4 V
    A48-18 (LHT) - Body ground
    G - Body ground
    Leveling motor LH operation signal input
    With low beam headlights on, vehicle height not changed
    Below 1 V
    With low beam headlights on, change vehicle height and keep for more than 3 seconds
    1.0 to 14.4 V
    A48-19 (SHRL) - Body ground
    SB - Body ground
    Rear height control sensor signal input
    Power switch off
    Below 1 V
    Power switch on (IG)
    0.5 to 4.5 V
    If the result is not as specified, the headlight leveling ECU assembly may have a malfunction.



      E038308
    1. Waveform 1
      Item
      Content
      Tool setting
      2 V/DIV., 2 ms./DIV.