Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.

  5. Read the Data List according to the display on the Techstream.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG SW
    Power switch IG signal/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    Parking Brake SW
    Parking brake switch signal/ON or OFF
    ON: Parking brake switch on
    OFF: Parking brake switch off
    -
    RR Door Courtesy SW
    Rear door courtesy light switch RH/ON or OFF
    ON: Rear door RH or LH open
    OFF: Rear door RH and LH closed
    -
    RL Door Courtesy SW
    Rear door courtesy light switch LH/ON or OFF
    ON: Rear door RH or LH open
    OFF: Rear door RH and LH closed
    -
    Back Door Courtesy SW
    Back door courtesy switch signal/ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    FR Door Courtesy
    Front door courtesy light switch RH signal/ON or OFF
    ON: Front door RH open
    OFF: Front door RH closed
    -
    FL Door Courtesy
    Front door courtesy light switch LH signal/ON or OFF
    ON: Front door LH open
    OFF: Front door LH closed
    -
    Dimmer SW
    Dimmer switch high position signal/ON or OFF
    ON: Dimmer switch in high or high flash position
    OFF: Dimmer switch in low position
    -
    Passing Light SW
    Dimmer switch high flash position (pass) signal/ON or OFF
    ON: Dimmer switch in high flash position
    OFF: Dimmer switch not in high flash position
    -
    Front Fog Light SW
    Front fog light switch signal/ON or OFF
    ON: Front fog light switch on
    OFF: Front fog light switch off
    -
    Auto Light SW
    Light control switch AUTO*1 or DRL*2 position signal/ON or OFF
    ON: Light control switch in AUTO*1 or DRL*2 position
    OFF: Light control switch not in AUTO*1 or DRL*2 position
    -
    Head Light SW (Head)
    Light control switch head position signal/ON or OFF
    ON: Light control switch in head position
    OFF: Light control switch not in head position
    -
    Head Light SW (Tail)
    Light control switch tail position signal/ON or OFF
    ON: Light control switch in tail or head position
    OFF: Light control switch in neither tail nor head position
    -
    Illumination Rate Info
    Illumination rate information/0 ms. to 99.99 ms.
    Value is output according to ambient light levels
    -

    1. *1: w/ Automatic Light Control
    2. *2: Headlight dimmer switch w/ DRL position

    HL Auto Leveling 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Headlight Low Beam State
    Low beam headlight state/ON or OFF
    ON: Low beam headlights on
    OFF: Low beam headlights off
    -
    +B
    IG power supply voltage value/0 to 19.75 V
    11 to 14 V
    -
    Height Sens Pw Supply Val
    Height control sensor power supply value/0 to 6.25 V
    Approx. 5 V
    -
    Rr Height Sens Signal Val
    Rear height control sensor signal value/0 to 5 V
    Approx. 2.5 V (When vehicle is level)
    Value changes according to vehicle height
    Vehicle Speed
    Vehicle speed/0 to 327.67 km/h (203.61 mph)
    Condition can be displayed
    -
    Rear Height Adjust Valid Flag
    Rear height adjustment range/VALID or INVALID
    Condition can be displayed
    -
    Init Writing Count
    Number of times for initialization/0 to 255
    Condition can be displayed
    -
    Number Of Trouble Codes
    Number of trouble codes/0 to 255
    Condition can be displayed
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Main Body / Active Test.

  5. Perform the Active Test according to the display on the Techstream.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Daytime Running Light
    Daytime running lights
    ON/OFF
    -
    Taillight Relay
    Taillight relay
    ON/OFF
    -
    Headlight Relay
    Headlight relays
    ON/OFF
    -
    Head Light Hi
    High beam headlights
    ON/OFF
    -
    Front Fog Light Relay
    Front fog light relay
    ON/OFF
    Light control switch is in tail position

    HL Auto Leveling 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Drive The Leveling Motor UP*1
    Leveling motor upward operation
    ON/OFF
    ON: Move up
    OFF: Stop
    Drive The Leveling Motor DOWN*1
    Leveling motor downward operation
    ON/OFF
    ON: Move down
    OFF: Stop
    *1: Perform the active test with the power switch on (READY).