ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU |
| CHECK POWER SWITCH |
Disconnect the L43 power switch connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L43-8 (AGND) - Body ground | P - Body ground | Ground | Always | Below 1 Ω |
Reconnect the L43 power switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L43-9 (TXCT) - L43-8 (AGND) | V - P | Key code output signal |
| Below 1 V |
| L43-9 (TXCT) - L43-8 (AGND) | V - P | Key code output signal |
| Pulse generation (See waveform 1) |
| L43-10 (CODE) - L43-8 (AGND) | L - P | Demodulated signal of key code data |
| Below 1 V |
| L43-10 (CODE) - L43-8 (AGND) | L - P | Demodulated signal of key code data |
| Pulse generation (See waveform 2) |
| L43-14 (VC5) - L43-8 (AGND) | Y - P | Power supply |
| Below 1 V |
| L43-14 (VC5) - L43-8 (AGND) | Y - P | Power supply |
| Pulse generation (See waveform 3) |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Item | Content |
| Tester Connection | L43-9 (TXCT) - L43-8 (AGND) |
| Tool Setting | 2 V/DIV., 50 ms./DIV. |
| Condition |
|
![]() |
Waveform 2 (Reference)
| Item | Content |
| Tester Connection | L43-10 (CODE) - L43-8 (AGND) |
| Tool Setting | 2 V/DIV., 50 ms./DIV. |
| Condition |
|
![]() |
Waveform 3 (Reference)
| Item | Content |
| Tester Connection | L43-14 (VC5) - L43-8 (AGND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition |
|
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Disconnect the L62 certification ECU (smart key ECU assembly) connector.

Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L62-1 (+B) - L62-15 (E) | B - W-B | +B power supply | Power switch off | 11 to 14 V |
| L62-15 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| L62-17 (CUTB) - L62-15 (E) | Y - W-B | Dark current cut fuse pin input signal | Power switch off | 11 to 14 V |
Reconnect the L62 certification ECU (smart key ECU assembly) connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L62-2 (IND) - Body ground | B - Body ground | Security indicator light signal |
| Below 2 V |
| L62-2 (IND) - Body ground | B - Body ground | Security indicator light signal |
| Pulse generation |
| L62-12 (TXCT) - L62-36 (AGND) | V - P | Power switch TXCT output |
| Below 1 V |
| L62-12 (TXCT) - L62-36 (AGND) | V - P | Power switch TXCT output |
| Pulse generation (See waveform 1) |
| L62-13 (CODE) - L62-36 (AGND) | L - P | Power switch CODE input |
| Below 1 V |
| L62-13 (CODE) - L62-36 (AGND) | L - P | Power switch CODE input |
| Pulse generation (See waveform 2) |
| L62-16 (IG) - L62-15 (E) | BE - W-B | IG power supply | Power switch off | Below 1 V |
| L62-16 (IG) - L62-15 (E) | BE - W-B | IG power supply | Power switch on (IG) | 11 to 14 V |
| L62-28 (VC5) - L62-36 (AGND) | Y - P | Power switch power supply |
| Below 1 V |
| L62-28 (VC5) - L62-36 (AGND) | Y - P | Power switch power supply |
| Pulse generation (See waveform 3) |
| L62-34 (EFII) - L62-15 (E)* | L - W-B | Power management control ECU (HV CPU) output signal | Power switch off | 11 to 14 V |
| L62-34 (EFII) - L62-15 (E)* | L - W-B | Power management control ECU (HV CPU) output signal | Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected | Pulse generation (See waveform 4) |
| L62-35 (EFIO) - L62-15 (E)* | R - W-B | Power management control ECU (HV CPU) input signal | Power switch off | Below 1 V |
| L62-35 (EFIO) - L62-15 (E)* | R - W-B | Power management control ECU (HV CPU) input signal | Power switch on (IG) | Pulse generation (See waveform 5) |
| L62-36 (AGND) - Body ground | P - Body ground | Power switch ground | Always | Below 1 Ω |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Item | Content |
| Tester Connection | L62-12 (TXCT) - L62-36 (AGND) |
| Tool Setting | 2 V/DIV., 50 ms./DIV. |
| Condition |
|
![]() |
Waveform 2 (Reference)
| Item | Content |
| Tester Connection | L62-13 (CODE) - L62-36 (AGND) |
| Tool Setting | 2 V/DIV., 50 ms./DIV. |
| Condition |
|
![]() |
Waveform 3 (Reference)
| Item | Content |
| Tester Connection | L62-28 (VC5) - L62-36 (AGND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition |
|
![]() |
Waveform 4 (Reference)
| Item | Content |
| Tester Connection | L62-34 (EFII) - L62-15 (E) |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected |
![]() |
Waveform 5 (Reference)
| Item | Content |
| Tester Connection | L62-35 (EFIO) - L62-15 (E) |
| Tool Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Power switch on (IG) |
| CHECK ID CODE BOX (IMMOBILISER CODE ECU) (for Canada) |
Disconnect the L10 ID code box (immobiliser code ECU) connector.

Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L10-1 (+B) - L10-8 (GND) | B - W-B | +B power supply | Power switch off | 11 to 14 V |
| L10-8 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the L10 ID code box (immobiliser code ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L10-5 (EFII) - L10-8 (GND) | L - W-B | Power management control ECU (HV CPU) output signal | Power switch off | 11 to 14 V |
| L10-5 (EFII) - L10-8 (GND) | L - W-B | Power management control ECU (HV CPU) output signal | Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected | Pulse generation (See waveform 1) |
| L10-6 (EFIO) - L10-8 (GND) | R - W-B | Power management control ECU (HV CPU) input signal | Power switch off | Below 1 V |
| L10-6 (EFIO) - L10-8 (GND) | R - W-B | Power management control ECU (HV CPU) input signal | Power switch on (IG) | Pulse generation (See waveform 2) |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Item | Content |
| Tester Connection | L10-5 (EFII) - L10-8 (GND) |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected |
![]() |
Waveform 2 (Reference)
| Item | Content |
| Tester Connection | L10-6 (EFIO) - L10-8 (GND) |
| Tool Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Power switch on (IG) |
| CHECK TRANSMISSION CONTROL ECU ASSEMBLY |
Disconnect the A23 and A24 transmission control ECU assembly connectors.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| A23-15 (BATT) - Body ground | SB - Body ground | Battery power supply | Power switch off | 11 to 14 V |
| A24-1 (E1) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| A24-5 (E02) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| A24-6 (E01) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| CHECK POWER MANAGEMENT CONTROL ECU (HV CPU) |
Disconnect the L5 power management control ECU (HV CPU) connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L5-6 (E1) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the L5 power management control ECU (HV CPU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L6-20 (IMO) - L5-6 (E1) | L - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 input signal | Power switch off | 11 to 14 V |
| L6-20 (IMO) - L5-6 (E1) | L - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 input signal | Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected | Pulse generation (See waveform 1) |
| L6-21 (IMI) - L5-6 (E1) | R - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 output signal | Power switch off | Below 1 V |
| L6-21 (IMI) - L5-6 (E1) | R - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 output signal | Power switch on (IG) | Pulse generation (See waveform 2) |
Waveform:
![]() |
Waveform 1 (Reference)
| Item | Content |
| Tester Connection | L6-20 (IMO) - L5-6 (E1) |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected |
![]() |
Waveform 2 (Reference)
| Item | Content |
| Tester Connection | L6-21 (IMI) - L5-6 (E1) |
| Tool Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Power switch on (IG) |
| COMBINATION METER ASSEMBLY |
Disconnect the L27 combination meter assembly connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L27-18 (B) - Body ground | R - Body ground | Battery | Power switch off | 11 to 14 V |
| L27-30 (ES) - Body ground | BR - Body ground | Ground (Signal ground) | Always | Below 1 Ω |
Reconnect the L27 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L27-19 (IG+) - Body ground | L - Body ground | Power switch signal | Power switch off | Below 1 V |
| L27-19 (IG+) - Body ground | L - Body ground | Power switch signal | Power switch on (IG) | 11 to 14 V |
| L27-22 (LP) - Body ground | B - Body ground | Security indicator light signal |
| Below 2 V |
| L27-22 (LP) - Body ground | B - Body ground | Security indicator light signal |
| Pulse generation |