ENGINE IMMOBILISER SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Smart Key / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | Power switch on (IG) signal/ON or OFF | ON: Power switch on (IG) or hybrid vehicle control system started OFF: Power switch off | - |
| Immobilizer when IG=ON | Immobiliser system status when power switch on (IG)l/UNSET or SET | SET: Power switch off UNSET: Power switch on (IG) or hybrid vehicle control system started | - |
| Immobiliser | Immobiliser system status/Set or Unset | Set: Power switch off Unset: Power switch on (IG) or hybrid vehicle control system started | - |
| Master Key | Master key code signal/Match or NoMatch | Match: Master key code sent NoMatch: Unmatched master key code sent | - |
| Sub Key | Sub-key (master key) code signal/Match or NoMatch | Match: Sub-key (master key) code sent NoMatch: Unmatched sub-key (master key) code sent | - |
| BCC Malfunction | Transponder chip signal/OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Abnormal Status | Transponder chip data/OK or NG | OK: Data OK NG: Data error | - |
| Different Encrypt Code | Transponder chip signal/OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Different Serial Number | Transponder chip signal/OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Frame Error | Transponder chip signal/OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Response | Transponder chip signal/OK or NG | OK: Correct data sent NG: Incorrect data sent | - |
| Wireless C Code | Wireless C Code/No Regd or Regd | No Regd: Wireless C Code not registered Regd: Wireless C Code registered | - |
| ID-BOX Sleep Condition | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 condition/Yes or No | Yes: Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 in sleep condition No: Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 not in sleep condition | - |
| ID-BOX Start Condition | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 condition/Yes or No | Yes: Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 sends wake up signal No: Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 not send wake up signal | - |
| Engine Start Request | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 start request condition/OK or NG | OK: Start request condition signal received NG: Start request condition signal not received | - |
| 3bit Code Request | 3bit code reception status/OK or NG | OK: 3bit code received NG: 3bit code not received | |
| S Code Check | S code verification result/OK or NG | OK: Verification confirmed NG: Verification not confirmed | - |
| L Code Check | L code verification result/OK or NG | OK: Verification confirmed NG: Verification not confirmed | - |
| Unlock Request Receive | Unlock command reception status/OK or NG | OK: Unlock request received NG: Unlock request not received | - |
| Lock Request Receive | Lock command reception status/OK or NG | OK: Lock request received NG: Lock request not received | - |
| S Code Check (Past) | S code verification result (past)/OK or NG(Past) | OK: Verification confirmed (past) NG(Past): Verification not confirmed (past) | - |
| L Code Check (Past) | L code verification result (past)/OK or NG(Past) | OK: Verification confirmed (past) NG(Past): Verification not confirmed (past) | - |
| EFI Code Receive | HV code receive (when DTC stored)/OK or NG | OK: HV code received NG: HV code not received | - |
| EFI Communication | HV communication/OK or NG | OK: HV communication normal NG: HV communication abnormal | - |
| # Codes | Number of trouble codes/Min.: 0 or Max.: 255 | Number of DTCs will be displayed | - |
| ACTIVE TEST |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Smart Key / Active Test.
Perform the Active Test according to the display on the Techstream.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Immobiliser Indicator | Security indicator light | ON or OFF | - |