Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > CUSTOMIZE PARAMETERS

for Preparation Click here



CUSTOMIZING FUNCTION WITH TECHSTREAM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Customize Setting / Light Control.

  5. Select the setting by referring to the table below.

    Light Control 
    Display
    Default
    Content
    Setting
    Relevant ECU
    Disp Ex ON Sen
    Normal
    Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*A
    Light2, Light1, Normal, Dark1 or Dark2
    Main Body ECU (Multiplex Network Body ECU)
    Disp Ex OFF Sen
    Normal
    Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B
    Light2, Light1, Normal, Dark1 or Dark2
    Light Auto OFF Delay
    30 s
    Keeps the headlights on for a certain period of time after turning the power switch off and closing all the doors with the low beam headlights on.
    Off, 30 s, 60 s or 90 s
    Response Time*1
    0.1 s
    Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position
    0.1 s or 1.0 s
    Sensitivity
    Normal
    Adjusts the sensitivity of the automatic light control system.*C
    Light2, Light1, Normal, Dark1 or Dark2
    DRL Function*2
    ON
    ON/OFF of the DRL function
    ON or OFF

    1. *1: w/o DRL
    2. *2: Headlight dimmer switch with DRL OFF

    HINT:
    The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


    *A 
    Brightness level required to dim the lights

    E107164

    Setting
    DARK2
    DARK1
    NORMAL
    LIGHT1
    LIGHT2

    *B 
    Brightness level required to cancel the dimming of the lights

    E107164

    Setting
    DARK2
    DARK1
    NORMAL
    LIGHT1
    LIGHT2

    *C 
    Sensitivity of the automatic light control system

    E107164

    Setting
    Dark2
    Dark1
    Normal
    Light1
    Light2


CUSTOMIZING FUNCTION WITH MULTI-DISPLAY (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (w/o Daytime Running Light))

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Turn the power switch on (IG).

  2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings.

  3. Select the setting by referring to the table below.

    Light Settings 
    Display
    Default
    Content
    Setting
    Relevant ECU
    Headlamps-On Sensitivity
    0
    Adjusts the sensitivity of the automatic light control system.*A
    -2, -1, 0, +1 or +2
    Main Body ECU (Multiplex Network Body ECU)
    Headlamps Auto-Off Timer
    30 sec.
    Keeps the headlights on for a certain period of time after turning the power switch off and closing all doors with the low beam headlights on.
    Off, 30 sec., 60 sec. or 90 sec.
    Daytime Running Lights*1
    On
    ON/OFF of the DRL function
    On or Off

    1. *1: Headlight dimmer switch with DRL OFF function.

    HINT:
    The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


    *A 
    Sensitivity of the automatic light control system

    E107164

    Setting
    -2
    -1
    0
    +1
    +2


CUSTOMIZING FUNCTION WITH MULTI-DISPLAY (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (w/ Daytime Running Light))

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Turn the power switch on (IG).

  2. Enter the following menus: SETUP / Vehicle.

  3. Select the setting by referring to the table below.

    Vehicle Settings 
    Display
    Default
    Content
    Setting
    Relevant ECU
    Light Sensor Sensitivity
    0
    Adjusts the sensitivity of the automatic light control system.*A
    -2, -1, 0, +1 or +2
    Main Body ECU (Multiplex Network Body ECU)
    Headlight Off Time Adjust
    30 sec.
    Keeps the headlights on for a certain period of time after turning the power switch off and closing all doors with the low beam headlights on.
    Off, 30 sec., 60 sec. or 90 sec.
    Daytime Running Lights*1
    On
    ON/OFF of the DRL function
    On or Off

    1. *1: Headlight dimmer switch with DRL OFF function.

    HINT:
    The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


    *A 
    Sensitivity of the automatic light control system

    E107164

    Setting
    -2
    -1
    0
    +1
    +2