KNEE AIRBAG ASSEMBLY > INSTALLATION |
| 1. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
![]() |
Connect the airbag connector and install the clamp to the driver side knee airbag assembly.
Push in the lock to install the airbag connector.
![]() |
Temporarily install the driver side knee airbag assembly with the 6 claws and 4 guides.
![]() |
Install the driver side knee airbag assembly with the 4 bolts.
| 2. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
Connect each connector.
Engage the clamp.
Engage the 2 guides and claw to connect the hood lock control cable.
![]() |
Engage the 6 claws and clip.
Install the lower instrument panel finish panel assembly with the screw <C>.
| 3. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
Connect each connector.
Engage the guide and claw.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <D>.
| 4. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the 2 clips.
Install the cowl side trim board LH with the clip.
| 5. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the 10 claws to install the front door scuff plate LH.
| 6. INSTALL NO. 1 SWITCH HOLE BASE |
Connect the connector.
Engage the 5 claws to install the No. 1 switch hole base.
| 7. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
Temporarily install the console box assembly.
![]() |
Engage the 9 claws as shown in the illustration.
Install the upper instrument panel finish panel assembly with the 2 bolts <A>.
Engage the clamp.
| 8. INSTALL CONSOLE BOX ASSEMBLY |
Connect the connector.
![]() |
Engage the 4 guides and 2 claws as shown in the illustration.
Install the console box assembly with the bolt <B> and 2 clips.
| 9. INSTALL BOX BOTTOM MAT |
Install the box bottom mat.
| 10. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.
| 11. INSTALL FRONT NO. 1 CONSOLE BOX INSERT |
![]() |
Engage the guide and 4 claws to install the front No. 1 console box insert as shown in the illustration.
| 12. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET |
Install the No. 2 console box mounting bracket with the 6 bolts <B>.
| 13. INSTALL ELECTRICAL KEY OSCILLATOR |
![]() |
Engage the clamp and install the electrical key oscillator.
Connect the connector.
| 14. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY |
![]() |
Install the shift lock control unit assembly with the 3 nuts.
Connect the connector to the shift lock control unit assembly.
| 15. INSTALL AIR CONDITIONING CONTROL ASSEMBLY |
Connect the connector.
![]() |
Engage the 4 claws to install the air conditioning control assembly.
| 16. INSTALL GLOVE COMPARTMENT DOOR |
Open the glove compartment door assembly.
![]() |
Insert the glove compartment door as shown in the illustration.
Engage the 7 claws to install the glove compartment door.
| 17. INSTALL NO. 2 INSTRUMENT PANEL REGISTER |
![]() |
Engage the 3 claws and clip to install the No. 2 instrument panel register.
| 18. INSTALL NO. 1 SIDE DEFROSTER NOZZLE |
![]() |
Engage the 3 claws to install the No. 1 side defroster nozzle.
| 19. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type) |
| 20. INSTALL NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type) |
![]() |
Engage the 4 claws and temporarily install the navigation receiver with bracket as shown in the illustration.
Install the navigation receiver with bracket with the 4 bolts.
| 21. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
Connect the connector.
Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.
| 22. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Connect the connector.
Engage the 14 claws to install the instrument cluster finish panel garnish.
| 23. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.
| 24. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Connect each connector.
Engage the 6 claws to install the integration control and panel assembly.
| 25. INSTALL REAR CONSOLE BOX ASSEMBLY |
| 26. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL |
| 27. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 28. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 29. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type) |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 30. PERFORM DIAGNOSTIC SYSTEM CHECK |
Perform a diagnostic system check (Click here).
| 31. INSPECT SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).