Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > CUSTOMIZE PARAMETERS


NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:
The following items can be customized.


POWER DOOR LOCK CONTROL SYSTEM
  1. Customizing with the Techstream

    Door Lock 
    Display
    Default
    Content
    Setting
    Unlock Key Twice
    ON
    Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.
    ON or OFF
    Auto Lock
    ON*1
    OFF*2
    Function that locks all doors when the vehicle speed reaches a certain level.
    ON or OFF
    Auto Lock/Shift
    ON*2
    OFF*1
    Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed.
    ON or OFF
    Auto Unlock/Shift
    ON
    Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY).
    ON or OFF
    All Unlock/Open-Close
    OFF
    Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off.
    ON or OFF

    1. *1: for Korea
    2. *2: except Korea

    Illuminated Entry 
    Display
    Default
    Content
    Setting
    Lighting Time
    15 s
    Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC) or (IG).)
    7.5 s, 15 s or 30 s

  2. Customizing with the Multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (w/o Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Settings / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Unlock on Second Key Turn
      On
      Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Lock by Speed
      On*1
      Off*2
      Function that locks all doors when the vehicle speed reaches a certain level.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Lock by Shift from P
      On*2
      Off*1
      Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Unlock by Shift to P
      On
      Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY).
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Unlock by Driver Door
      Off
      Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off.
      On or Off
      Main body ECU (Multiplex network body ECU)

      1. *1: for Korea
      2. *2: except Korea

  3. Customizing with the Multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (w/ Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Speed Sensitive Auto Lock
      Off
      Function that locks all doors when the vehicle speed reaches a certain level.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Shift-Linked Auto Lock
      On
      Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Shift-Linked Auto Unlock
      On
      Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY).
      On or Off
      Main body ECU (Multiplex network body ECU)


WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Customizing with the Techstream

    Wireless Door Lock Control System 
    Display (item)
    Default
    Function
    Setting
    Wireless Control
    ON
    Function that turns wireless door lock function on or off
    ON or OFF
    Hazard Answer Back
    ON
    When the doors are locked by wireless operation, the hazard warning lights flash once.
    When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
    ON or OFF
    Open Door Warning
    ON
    The buzzer sounds when lock is pressed when any of the doors are ajar.
    ON or OFF
    Unlock 2 Operation
    ON
    Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.
    ON or OFF
    Panic Function
    ON
    Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds
    ON or OFF
    Auto Lock Time
    60 s*1 or 30 s*2
    Function that regulates the interval between unlocking and automatic relocking of doors
    30 s, 60 s or 120 s
    Wireless Auto Lock
    ON
    This function turns the wireless auto lock function on or off.
    ON or OFF
    Wireless Buzzer Resp
    ON
    Wireless door lock buzzer response
    ON or OFF
    Wireless Buzzer Vol
    Level7
    Wireless door lock buzzer volume
    Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0

    1. *1: except for Korea
    2. *2: for Korea

    Illuminated Entry 
    Display
    Default
    Content
    Setting
    Lighting Time
    15 s
    Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).)
    7.5 s, 15 s or 30 s

  2. Customizing with the Multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (w/o Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-Press Unlock
      On
      Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Relock Timer
      60 s*1
      30 s*2
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Lights
      On
      When the doors are locked by wireless operation, the hazard warning lights flash once.
      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Tone
      7
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

      1. *1: except Korea
      2. *2: for Korea

  3. Customizing with the Multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (w/ Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-Press Unlock
      On
      Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock Feedback Volume
      7
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)


SMART KEY SYSTEM (for Entry Function)
  1. Customizing with the Techstream

    Smart Key / Access 
    Tester Display
    Default
    Content
    Setting
    Park Wait Time
    2.5 s
    Function that sets waiting time to permit opening door after door is locked with entry lock function
    0.5 s, 1.5 s, 2.5 s or 5 s
    Ignition Available Area
    All
    Function that switches the entry hybrid vehicle control system start detection area
    Front or All*1
    Back Door Opening Operation*2
    Long
    Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch)
    Long, Twice or OFF
    Door Unlock Mode*2, *3
    Driver
    Function that chooses the doors to be operated by entry unlock operation
    All or Driver
    Touch Activation Over Threshold
    Active
    The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.
    Active or Not Active

    1. *1: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected.
    2. *2: w/ Entry System Back Door Open Function
    3. *3: except for Korea and Mexico

    Warning 
    Tester Display
    Default
    Content
    Setting
    Key Low Battery Warning
    ON
    Function that warns driver that the key battery is weak
    ON or OFF

  2. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (w/o Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Setting.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Select Doors to Unlock
      Driver's Door
      Function that sets which doors are unlocked by the entry unlock function.
      All Doors or Driver's Door
      Certification ECU (smart key ECU assembly)
      Key System with Elec. Key*1
      Entry and Start System*2
      On
      Function that enables or disables the smart key system.
      On or Off
      Certification ECU (smart key ECU assembly)

      1. *1: except Korea
      2. *2: for Korea

  3. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (w/ Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Key System with Elec. Key*1
      Entry and Start System*2
      On
      Function that enables or disables the smart key system.
      On or Off
      Certification ECU (smart key ECU assembly)

      1. *1: except Korea
      2. *2: for Korea


ENTRY UNLOCK MODE SWITCHING* (SMART KEY SYSTEM (for Entry Function))
*: except for Korea and Mexico
  1. Check that the power source mode is OFF and the LED on the key is not blinking. Press the LOCK button and one of the other buttons on the key at the same time for approximately 5 seconds while the key is in the actuation area.
    Driver door unlock default setting:
    When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

    NOTICE:
    After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.

    1. Driver door unlock mode:
      When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.*
      *: w/ Entry System Back Door Open Function
    2. All door unlock mode:
      When any touch sensor is touched, all doors unlock.

  2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the smart key system to entry unlock mode.

  3. The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer assembly.

    Mode
    Wireless Door Lock Buzzer Assembly
    Driver Door
    (Default)
    Sounds 3 times
    All Doors
    (Customized)
    Sounds 2 times

    HINT:
    The procedure only changes entry unlock mode of the smart key system. It does not switch the unlocking of the wireless door lock control.


ELECTRICAL KEY CANCEL (SMART KEY SYSTEM (for Entry Function))
The electrical key cancel operation disables the following functions:
  1. Entry Unlock/Lock
  2. Entry Hybrid Vehicle Control System Start
  3. Entry System Back Door Open Function*
    *: w/ Entry System Back Door Open Function
  4. Electrical Key Lock-in Prevention
  5. Warning
  1. The operation procedure is as follows:
    Precondition:
    Power switch off, driver door closed and unlocked.

    1. Push the unlock switch of the key once.

    2. Open the driver door within 5 seconds.

    3. Push the unlock switch of the key twice within 5 seconds.

    4. Close and open the driver door twice within 30 seconds.
      (Driver door: Close → Open → Close → Open)

    5. Push the unlock switch of the key twice within 5 seconds.

    6. Close and open the driver door within 30 seconds.
      (Driver door: Close → Open)

    7. Close the driver door within 5 seconds.
      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
      To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.


SMART KEY SYSTEM (for Start Function)
  1. Customizing with the Techstream

    Smart Key / Access 
    Tester Display
    Default
    Content
    Setting
    Ignition Available Area (Entry ignition available area)
    All
    Function to choose the available area for electrical key to start the hybrid control system.
    Front or All*

    1. *: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected.

  2. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (w/o Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Setting.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Key System with Elec. Key*1
      Entry and Start System*2
      On
      Function that enables or disables the smart key system.
      On or Off
      Certification ECU (smart key ECU assembly)

      1. *1: except Korea
      2. *2: for Korea

  3. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (w/ Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Key System with Elec. Key*1
      Entry and Start System*2
      On
      Function that enables or disables the smart key system.
      On or Off
      Certification ECU (smart key ECU assembly)

      1. *1: except Korea
      2. *2: for Korea


CUSTOMIZING FUNCTION WITHOUT TECHSTREAM (SMART KEY SYSTEM (for Start Function))
Performing the following procedure disables the smart key system.

HINT:
To start the hybrid control system while the smart key system is disabled, follow the procedure for when the key battery is low (Click here).

  1. The operation procedure is as follows:
    Precondition:
    Power switch off, driver door closed and unlocked.

    1. Push the unlock switch of the key once.

    2. Open the driver door within 5 seconds.

    3. Push the unlock switch of the key twice within 5 seconds.

    4. Close and open the driver door twice within 30 seconds.
      (Driver door: Close → Open → Close → Open)

    5. Push the unlock switch of the key twice within 5 seconds.

    6. Close and open the driver door within 30 seconds.
      (Driver door: Close → Open)

    7. Close the driver door within 5 seconds.
      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
      To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.


LIGHTING SYSTEM (LIGHTING INT)
  1. Customizing with the Techstream

    Illuminated Entry 
    Tester Display
    Default
    Content
    Setting
    Relevant ECU
    Lighting Time
    15 s
    Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)
    7.5 s, 15 s or 30 s
    Main body ECU (Multiplex network body ECU)
    I/L when ACC OFF
    ON
    Lights up power switch illumination, front interior lights, rear interior light and footwell lights when the power switch is turned from on (ACC or IG) to off.
    ON or OFF
    I/L ON W/Door Key Unlock
    ON
    Lights up power switch illumination, front interior lights, rear interior light and footwell lights when doors are unlocked using a mechanical key or door control transmitter.
    ON or OFF
    Light Control
    ON
    Dims (ON setting) or turns off (OFF setting) the footwell lights under the following conditions:
    Power switch on (IG), shift lever not in P, and all doors closed.
    ON or OFF
    Room Light when Aprchd
    ON
    Lights up the power switch illumination, front interior lights, rear interior light and footwell lights when a key enters any actuation area around the doors.
    ON or OFF
    Inside Foot Light
    ON
    ON/OFF of footwell light control function.
    ON or OFF

  2. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (w/o Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Light Settings.

    3. Select the setting by referring to the table below.

      Light Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Interior Lights Off Timer
      15 sec.
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)
      Off, 7.5 sec., 15 sec., or 30 sec.
      Main body ECU (Multiplex network body ECU)


METER / GAUGE SYSTEM

Warning 
Tester Display
Default
Content
Setting
Key Remind Sound
Slow
Function to change the cycle of the key reminder buzzer
Normal, Fast or Slow
Driver Side Seatbelt Warning Buzzer*1
ON
Function to turn on/off the seat belt warning buzzer
ON or OFF
Front Passenger Side Seatbelt Warning Buzzer*1
ON
Function to turn on/off the seat belt warning buzzer
ON or OFF
Rear Seatbelt Warning Buzzer*2
ON
Function to turn on/off the rear seat belt warning buzzer
ON or OFF
Reverse Buzzer
Continual
Function to change the type of the reverse warning buzzer
Single or Continual
  1. *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more.
  2. *2: w/ Rear Seat Belt Warning

SEAT BELT WARNING SYSTEM

Combination Meter 
Tester Display
Default
Content
Setting
Driver Side Seatbelt Warning Buzzer
ON
Function to sound the seat belt warning buzzer
ON / OFF
Front Passenger Side Seatbelt Warning Buzzer
ON
Function to sound the seat belt warning buzzer
ON / OFF

HINT:
This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.


AIR CONDITIONING SYSTEM
  1. Customizing with the Techstream

    Air Conditioner 
    Display (Item)
    Default
    Content
    Setting
    Set Temperature Shift
    Normal
    Function to control with the shifted temperature against the displayed temperature.
    -2C, -1C, Normal, +1C, +2C
    Compressor Mode*3
    Automatic
    Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off.
    Manual or Automatic
    Air inlet Mode*2
    Automatic
    In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode
    Manual or Automatic
    Foot/DEF Auto Mode
    ON
    Function to automatically turn the airflow from FOOT/DEF on when AUTO mode is on.
    ON or OFF
    Foot/DEF Automatic Blow Up Function
    ON
    Function to automatically increase the blower level when the defroster is on.
    ON or OFF
    Ambient Temperature Shift
    Normal
    Function to control the shifted ambient temperature in relation to the displayed ambient temperature.
    -3C, -2C, -1C, Normal, +1C, +2C, +3C
    ECO MODE Cancel
    OFF
    Function to cancel the ECO mode drive when item is on.
    OFF or ON
    Noise and Vibration Reduction
    OFF
    Function to change speed of the compressor when item is on.
    OFF or ON
    Start Pre A/C*1
    Long1
    Function to set the activation operation method for the remote air conditioning system using the key (electrical transmitter).
    1 tim ON, 2 tim ON, Long1 or Long2
    Stop Pre A/C*1
    2 tim ON
    Function to set the stop operation method for the remote air conditioning system using the key (electrical transmitter).
    1 tim ON, 2 tim ON, Long1 or Long2

    1. *1: w/ Remote Air Conditioning System
    2. *2: for Korea and Mexico
    3. *3: except Korea and Mexico

  2. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Settings / Climate Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Auto A/C Mode*2
      On
      Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off
      On or Off
      Air conditioning amplifier assembly
      Efficient Ventilation Mode*1
      On
      In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode
      On or Off
      Air conditioning amplifier assembly

      1. *1: for Korea
      2. *2: except Korea


POWER WINDOW CONTROL SYSTEM

Power Window 
Tester Display
Default
Content
Setting
Relevant ECU
P Window Auto Up
Avail
This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger door).
Not Avl/Avail
Power window ECU (Power window regulator motor assembly)
P Window Auto Up From Driver
Avail
This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly.
Not Avl/Avail
Power window ECU (Power window regulator motor assembly)
RR Window Auto Up
Avail
This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH door).
Not Avl/Avail
Power window ECU (Power window regulator motor assembly)
RR Window Auto Up From Driver
Avail
This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly.
Not Avl/Avail
Power window ECU (Power window regulator motor assembly)
RL Window Auto Up
Avail
This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH door).
Not Avl/Avail
Power window ECU (Power window regulator motor assembly)
RL Window Auto Up From Driver
Avail
This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly.
Not Avl/Avail
Power window ECU (Power window regulator motor assembly)

LIGHTING SYSTEM (LIGHTING EXT)
  1. Customizing with the Techstream

    Light Control 
    Display
    Default
    Content
    Setting
    Relevant ECU
    Disp Ex ON Sen
    Normal
    Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*A
    Light2, Light1, Normal, Dark1 or Dark2
    Main Body ECU (Multiplex Network Body ECU)
    Disp Ex OFF Sen
    Normal
    Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B
    Light2, Light1, Normal, Dark1 or Dark2
    Light Auto OFF Delay
    30 s
    Keeps the headlights on for a certain period of time after turning the power switch off and closing all the doors with the low beam headlights on.
    Off, 30 s, 60 s or 90 s
    Response Time*1
    0.1 s
    Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position
    0.1 s or 1.0 s
    Sensitivity
    Normal
    Adjusts the sensitivity of the automatic light control system.*C
    Light2, Light1, Normal, Dark1 or Dark2
    DRL Function*2
    ON
    ON/OFF of the DRL function
    ON or OFF

    1. *1: w/o DRL
    2. *2: Headlight dimmer switch with DRL OFF

    HINT:
    The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


    *A 
    Brightness level required to dim the lights

    E107164

    Setting
    DARK2
    DARK1
    NORMAL
    LIGHT1
    LIGHT2

    *B 
    Brightness level required to cancel the dimming of the lights

    E107164

    Setting
    DARK2
    DARK1
    NORMAL
    LIGHT1
    LIGHT2

    *C 
    Sensitivity of the automatic light control system

    E107164

    Setting
    Dark2
    Dark1
    Normal
    Light1
    Light2

  2. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (w/o Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings.

    3. Select the setting by referring to the table below.

      Light Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Headlamps-On Sensitivity
      0
      Adjusts the sensitivity of the automatic light control system.*A
      -2, -1, 0, +1 or +2
      Main Body ECU (Multiplex Network Body ECU)
      Headlamps Auto-Off Timer
      30 sec.
      Keeps the headlights on for a certain period of time after turning the power switch off and closing all doors with the low beam headlights on.
      Off, 30 sec., 60 sec. or 90 sec.
      Daytime Running Lights*1
      On
      ON/OFF of the DRL function
      On or Off

      1. *1: Headlight dimmer switch with DRL OFF function.

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Sensitivity of the automatic light control system

      E107164

      Setting
      -2
      -1
      0
      +1
      +2

  3. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (w/ Daytime Running Light))

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle.

    3. Select the setting by referring to the table below.

      Vehicle Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Light Sensor Sensitivity
      0
      Adjusts the sensitivity of the automatic light control system.*A
      -2, -1, 0, +1 or +2
      Main Body ECU (Multiplex Network Body ECU)
      Headlight Off Time Adjust
      30 sec.
      Keeps the headlights on for a certain period of time after turning the power switch off and closing all doors with the low beam headlights on.
      Off, 30 sec., 60 sec. or 90 sec.
      Daytime Running Lights*1
      On
      ON/OFF of the DRL function
      On or Off

      1. *1: Headlight dimmer switch with DRL OFF function.

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Sensitivity of the automatic light control system

      E107164

      Setting
      -2
      -1
      0
      +1
      +2


VEHICLE PROXIMITY NOTIFICATION SYSTEM
  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Utility / Customize Setting / Others.

    5. Select the setting by referring to the table below.

      Vehicle Proximity Notification System 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Proximity Sound Volume Adjustment
      Standard
      Function that sets the warning sound volume in 3 levels
      Standard, Standard +1, Standard +2
      Vehicle Approaching Speaker Controller
      Proximity Sound Level Increase (Vehicle Starting)
      ON
      Function that amplifies the warning sound when the vehicle starts off
      ON or OFF
      Vehicle Approaching Speaker Controller
      Proximity Sound Control (Vehicle Stationary)
      OFF
      Function that sets the warning sound when the vehicle is stopped
      ON or OFF
      Vehicle Approaching Speaker Controller