Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM

PRE-COLLISION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Pre-Collision / Data List.

  5. Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.

  6. Read the Data List according to the display on the Techstream.

    HINT:
    As the driving support ECU and seat belt control ECU have Data List for pre-collision system, be sure to check the Pre-Collision and Pre-Collision 2 Data Lists.


    Pre-Collision 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Driver Buckle SW
    Buckle switch status of driver side seat/
    UNSET / SET / NG
    UNSET: Driver side seat belt unfastened
    SET: Driver side seat belt fastened
    NG: Indeterminate data
    -
    Passenger Buckle SW
    Buckle switch status of passenger side seat/
    UNSET / SET / NG
    UNSET: Passenger side seat belt unfastened
    SET: Passenger side seat belt fastened
    NG: Indeterminate data
    -
    Drive Belt Control
    Seat belt control status of driver side seat/
    STOP / ON / ERROR
    STOP: Control stopped
    ON: Controlled
    ERROR: Indeterminate data
    Seat belt (driver side) is fastened
    Passenger Belt Control
    Seat belt control status of passenger side seat/
    STOP / ON / ERROR
    STOP: Control stopped
    ON: Controlled
    ERROR: Indeterminate data
    Seat belt (passenger side) is fastened
    Number of Trouble Code
    Number of past trouble codes/min: 0, max: 255
    Number of DTCs will be displayed
    -

    Pre-Collision2 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Wiper Information
    Wiper operational status/
    Unoperat, Oil off, Mist, Washer, Unknown, Intermittent, Lo, Hi
    The respective operational status displayed
    -
    Head Light information
    Headlight operational status/
    Unknown, Fail, Prohibited, Direct, Hi, Passing, Fail
    -
    -
    Head Light
    Headlight switch position signal/
    ON or OFF
    ON: Headlight switch on
    OFF: Headlight switch off
    -
    Head Light (High Beam)
    High beam headlight switch position signal/
    ON or OFF
    ON: High beam headlight switch on
    OFF: High beam headlight switch off
    -
    Pre-Collision Brake OFF Switch
    Pre-collision brake cancel switch status/
    ON or OFF
    ON: Pre-collision cancel switch on
    OFF: Pre-collision cancel switch off
    -
    Pre-Collision System
    Pre-collision system control/
    Valid or Inval
    Valid: Pre-collision system control possible
    Inval: Pre-collision system control not possible
    -
    DCam Indicator
    Driver camera indicator display request signal/
    ON or OFF
    ON: Driver camera indicator display requested
    OFF: Driver camera indicator display not requested
    Not Supported
    PCS Indicator
    "CHECK PCS SYSTEM" display request signal/
    ON or OFF
    ON: "CHECK PCS SYSTEM" display requested
    OFF: "CHECK PCS SYSTEM" display not requested
    -
    PCS Disabled Indicator
    "PCS TEMPORARILY NOT AVAILABLE" display request signal/
    ON or OFF
    ON: "PCS TEMPORARILY NOT AVAILABLE" display requested
    OFF: "PCS TEMPORARILY NOT AVAILABLE" display not requested
    -
    Pre-Collision Safety Warning Ind
    PCS system warning status/
    ON or OFF
    ON: Pre-collision warning indicator on
    OFF: Pre-collision warning indicator off
    -
    Pre-Collision Safety Brake Ind
    PCS system "BRAKE!" alert status/
    ON or OFF
    ON: PCS system "BRAKE!" alert on
    OFF: PCS system "BRAKE!" alert off
    -
    Pre-Collision Safety Warning Buz
    PCS system warning buzzer/
    Valid or Inval
    Valid: PCS system warning buzzer operation possible
    Inval: PCS system warning buzzer operation not possible
    -
    Pre-Collision Brake
    Pre-collision brake function/
    Valid or Inval
    Valid: Pre-collision brake operation possible
    Inval: Pre-collision brake operation not possible
    -
    Front Radar PSB
    Front radar-linked pre-collision seat belt activation signal/
    ON or OFF
    ON: Front radar-linked pre-collision seat belt activated
    OFF: Front radar-linked pre-collision seat belt not activated
    Status changes when the pre-collision seat belt is activated before a collision
    PBA Start
    Pre-collision brake assist activation signal/
    ON or OFF
    ON: Pre-collision brake assist activated
    OFF: Pre-collision brake assist not activated
    Signal status changes when the pre-collision brake assist is activated before a collision
    (Pre-collision brake will activate only in situations where the driver depresses the brake pedal)
    Warning Brake
    Warning brake activation/
    ON or OFF
    ON: Warning brake operation activated
    OFF: Warning brake operation not activated
    Signal status changes when the warning brake function lightly applies the brakes to warn the driver when signals from the driver monitor determine that the driver is not facing the camera
    Brake Assist Standby
    Supplemental brake pressure signal/
    ON or OFF
    ON: Supplemental brake pressure being provided
    OFF: Supplemental brake pressure not being provided
    Signal status changes when supplemental brake pressure is being provided after a collision is judged as unavoidable and before the brake pedal is depressed
    Pre-Collision Brake Control
    Pre-collision brake operational status/
    ON or OFF
    ON: Pre-collision brake operating
    OFF: Pre-collision brake function not operating
    Status changes when pre-collision brake operates before a collision
    AVS Start
    AVS control activation status/
    ON or OFF
    ON: AVS control activated
    OFF: AVS control not activated
    Status changes when the suspension is controlled (stiffened) prior to a collision
    CCS Cancel
    Automatic cancellation of cruise control during pre-collision brake activation/
    ON or OFF
    ON: Cruise control automatically canceled
    OFF: Cruise control not automatically canceled
    -
    Front Radar-Dirt History
    Millimeter wave radar sensor assembly dirt history/
    ON or OFF
    ON: History of excessive dirt
    OFF: No history of excessive dirt
    -
    Front Radar-Environment Hist
    Millimeter wave radar sensor temperature condition history/
    Good or Bad
    Good: No history of excessive temperature
    Bad: History of excessive temperature
    -
    Recognition Camera Image History
    Lane-recognition camera malfunction history/
    ON or OFF
    ON: History of lane-recognition camera malfunction
    OFF: No history of lane-recognition camera malfunction
    -
    Recog ECU H Temp Stop
    Lane-recognition ECU high temperature stop status/
    Normal or Stop
    Normal: System normal
    Stop: Lane-recognition ECU stopped
    Power to the CPU is cut off due to excessive ECU temperature
    Recog ECU Recognize Img
    Lane-recognition ECU image recognition status/
    Normal or Abnormal
    Normal: Normal Image recognition
    Abnormal: Image recognition malfunction
    Image recognition cannot be performed due to excessive ECU temperature
    Recog ECU H Temp Hist
    Lane-recognition ECU temperature condition history/
    ON or OFF
    ON: No history of excessive temperature
    OFF: History of excessive temperature
    -
    Recognition Camera Voltage
    Lane-recognition camera voltage status/
    Normal or Low
    Normal: Normal voltage
    Low: Low voltage
    -
    Camera Height
    Memorized camera height/
    Display range: Memorized camera height
    Memorized camera height displayed
    -
    Camera Horizontal
    Memorized camera horizontal position/
    Display range: Memorized camera horizontal position
    Memorized camera horizontal position displayed
    -
    Target Height
    Memorized target height
    Memorized target height displayed
    -
    Target Distance
    Memorized target distance
    Memorized distance from the camera to the target displayed
    -
    Curr Com PCS-WIL-R
    Driver seat active headrest ECU connection status/
    without or with
    with: Driver seat active headrest ECU connected
    without: Driver seat active headrest ECU not connected
    Not Supported
    Curr Com PCS-WIL-L
    Front passenger seat active headrest ECU connection status/
    without or with
    with: Front passenger seat active headrest ECU connected
    without: Front passenger seat active headrest ECU not connected
    Not Supported
    Curr Com Night View ECU
    Night view ECU connection status/
    without or with
    with: Night view ECU connected
    without: Night view ECU not connected
    Not Supported
    Country# (DSS)
    Destination country for driving support computer/
    JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC, NOFIX
    Actual country code
    -
    Country# (Object Recog ECU)
    Destination country for lane recognition camera sensor/
    JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC, NOFIX
    Actual country code
    -
    The Number of DTCs
    Number of DTCs/
    0 to 255
    When system is normal: 0
    When a malfunction is detected: More than 0
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Pre-Collision / Active Test.

  5. Perform Active Test according to the display on the Techstream.

    HINT:
    The power switch must be turned on (IG) to proceed with the Active Test using the Techstream.


    Pre-Collision 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Driver Seat Belt Motor
    Driver seat belt motor
    ON: Seat belt motor operates
    OFF: Seat belt motor does not operate
    Seat belt (driver side) is fastened
    Passenger Seat Belt Motor
    Passenger seat belt motor
    ON: Seat belt motor operates
    OFF: Seat belt motor does not operate
    Seat belt (passenger side) is fastened
    Driver and Passenger Seat Belt Motor
    Driver and passenger seat belt motors
    ON: Seat belt motors operate
    OFF: Seat belt motors do not operate
    Seat belts (driver and passenger sides) are fastened

    NOTICE:
    1. The seat belt motor will only operate when the tongue plate is inserted into the buckle (seat belt fastened).
    2. To prevent overheating the belt motor, this test cannot be activated continuously. Operate it using at least a 30-second interval.