Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM

PRE-COLLISION SYSTEM > Power Source Circuit

for Preparation Click here


DESCRIPTION

This circuit supplies power to the seat belt control ECU.

WIRING DIAGRAM


E183051E13


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (PGND CIRCUIT)


    E172287E31
  1. Disconnect the seat belt control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L2-8 (PGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Seat Belt Control ECU)

  1. Reconnect the seat belt control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PGND CIRCUIT)
OK


2.CHECK HARNESS AND CONNECTOR (IG1 CIRCUIT)


    E172286E09
  1. Disconnect the seat belt control ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L3-8 (IG1) - L2-8 (PGND)
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Seat Belt Control ECU)
    *2
    Front view of wire harness connector
    (to Seat Belt Control ECU)

  1. Reconnect the seat belt control ECU connector.



NG
Go to step 4
OK


3.CHECK HARNESS AND CONNECTOR (+B CIRCUIT)


    E172287E15
  1. Disconnect the seat belt control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L2-7 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Seat Belt Control ECU)

  1. Reconnect the seat belt control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+B CIRCUIT)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the instrument panel junction block assembly.


    E183073E02


    Text in Illustration 
    *1
    Instrument Panel Junction Block Assembly
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2E-1 - 2B-16
    Always
    10 kΩ or higher
    2E-1 - 2B-16
    When battery voltage applied to terminals 2B-25 and 2B-6
    Below 1 Ω

  1. Reinstall the instrument panel junction block assembly.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - SEAT BELT CONTROL ECU)


    E183981E05
  1. Disconnect the instrument panel junction block assembly connector.

  1. Disconnect the seat belt control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2B-16 - L3-8 (IG1)
    Always
    Below 1 Ω
    2B-16 - Body ground
    Always
    10 kΩ or higher
    L3-8 (IG1) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Seat Belt Control ECU)
    *2
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)

  1. Reconnect the seat belt control ECU connector.

  1. Reconnect the instrument panel junction block assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - SEAT BELT CONTROL ECU)
OK


6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BODY GROUND)


    E189244E01
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2B-6 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)

  1. Reconnect the instrument panel junction block assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BODY GROUND)
OK


7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - POWER MANAGEMENT ECU)


    A217245E01
  1. Disconnect the instrument panel junction block assembly connector.

  1. Disconnect the power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2B-25 - L6-2 (IG1D)
    Always
    Below 1 Ω
    2B-25 - Body ground
    Always
    10 kΩ or higher
    L6-2 (IG1D) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Power Management control ECU)
    *2
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)

  1. Reconnect the power management control ECU connector.

  1. Reconnect the instrument panel junction block assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - POWER MANAGEMENT ECU)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY)