Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When communication fails in any of the CAN bus wires (communication wires), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.

  2. The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)

    Function
    (Function Description)
    Control Master
    System Related
    Fail-safe Operation
    DTC
    (Driver Detectable)
    Power switch
    (Power source control)
    Power management control ECU
    1. Transmission control ECU
    2. Skid control ECU
    3. Main body ECU
    1. Power switch does not change to on (READY) even when power switch is pressed with the brake pedal depressed
    2. Power switch off is prohibited
    U0129
    U0293
    (Warning and indicator lights come on)
    Hybrid driving control
    Power management control ECU
    ECM
    Only motor operation is used (Engine is not used)
    U0100
    (Warning and indicator lights come on)
    Shift position indicator display
    Transmission control ECU
    1. Power management control ECU
    2. Main body ECU
    3. Combination meter
    Shift position indicator is not displayed
    U0146
    (Warning and indicator lights come on)
    Regenerative braking control
    Power management control ECU
    Skid control ECU
    Regenerative braking will stop
    (ABS/VSC control gradually stops)
    U0073
    U0129
    U0293
    (Warning and indicator lights come on)
    VSC control
    (Controls driving force while VSC operating)
    Skid control ECU
    1. Power management control ECU
    2. Yaw rate sensor
    3. Steering angle sensor
    ABS/VSC control is inoperative
    (ABS/VSC control gradually stops)
    U0073
    U0123
    U0124
    U0126
    U0293
    (Warning and indicator lights come on)
    ABS control
    (Controls driving force while ABS operating)
    Skid control ECU
    Yaw rate sensor
    ABS control is inoperative
    (ABS control gradually stops)
    U0073
    U0123
    U0124
    (Warning and indicator lights come on)
    TRAC control
    (Engine power control by VSC/TRAC)
    Skid control ECU
    1. Power management control ECU
    2. Yaw rate sensor
    3. Steering angle sensor
    ABS/VSC control is inoperative
    (ABS/VSC control gradually stops)
    U0073
    U0123
    U0124
    U0126
    U0293
    (Warning and indicator lights come on)
    Electric power steering control
    (Speed of vehicle induction type torque control)
    Power steering ECU
    1. Power management control ECU
    2. Skid control ECU
    Depression of EPS assist
    (Deterioration of steering assist)
    U0129
    U0293
    (Warning light comes on)
    Air conditioning control
    (Air conditioning control is in cabin)
    Air conditioning amplifier
    1. Power management control ECU
    2. ECM
    3. Combination meter
    4. Main body ECU
    Air conditioning function and PTC heater function stop
    U0100
    U0142
    U0155
    U0293
    (Air conditioning is inoperative)
    Entry function/Power door lock control
    1. Certification ECU
    2. Main Body ECU
    1. ECM
    2. Combination meter
    3. Power management control ECU
    4. Center airbag sensor assembly
    Unlock permitted
    U0100
    U0101
    U0142
    U0151
    U0155
    U0293
    U0327
    U1133
    (Wireless door lock cannot operate)
    Navigation Eco display
    1. Displays fuel consumption per minute and regeneration amount in chart and displays history of average fuel economy
    1. Navigation ECU Sub-assembly*1*2
    2. Radio and Display Receiver Assembly*2
    1. Power management control ECU
    2. Skid control ECU
    3. ECM
    4. Combination meter
    On the navigation Eco screen:
    1. Update of the per-minute fuel consumption display (per minute fuel consumption calculation) on the navigation Eco screen (per-minute fuel consumption screen) is stopped
    2. Update of the current average fuel economy display on the navigation Eco screen (block fuel consumption screen) is stopped
    3. If drivable mileage is displayed on the navigation Eco screen (block fuel consumption screen), the numeric part of the drivable mileage disappears because drivable mileage data cannot be received
    U0100
    U0155
    U0293
    (None)
    Energy monitor display
    1. Creates energy flow screen which indicates regeneration status and drive force transmission status
    1. Navigation ECU Sub-assembly*1*2
    2. Radio and Display Receiver Assembly*2
    Power management control ECU
    Energy flow is not displayed
    U0100
    U0293
    (None)
    Destination identification
    1. Identifies destination based on destination and destination package information, and selects the time zone and language used for the display
    1. Navigation ECU Sub-assembly*1*2
    2. Radio and Display Receiver Assembly*2
    Main body ECU
    Destination is identified based on information received before communication is interrupted.
    U0140
    (None)
    Vehicle customization function
    1. Allows changing of operation and control conditions for vehicle functions via multi-display operation
    1. Navigation ECU Sub-assembly*1*2
    2. Radio and Display Receiver Assembly*2
    1. Certification ECU
    2. Main body ECU
    3. Air conditioning amplifier
    When an application that uses remote communication is activated (customization/remote diagnosis), the process will be performed regardless of main body ECU remote communication permit/prohibit state
    U0073
    (None)
    Time stamp function
    1. Diagnostic function that links relative time information from the main body ECU (multiplex network body ECU) and absolute time (actual time) obtained from GPS
    1. Navigation ECU Sub-assembly*1
    2. Main body ECU
    -
    -
    U0073
    (None)
    Rear view monitor control
    1. Displays rear view monitor (without guide lines)
    1. Navigation ECU Sub-assembly*1*2
    2. Radio and Display Receiver Assembly*2
    1. Power management control ECU
    2. Main body ECU
    Screen does not change to camera display.
    U0100
    (None)
    Vehicle-to-vehicle distance control
    Driving support ECU
    1. Power management control ECU
    2. Skid control ECU
    3. ECM
    4. Steering angle sensor
    5. Yaw rate sensor
    6. Main body ECU
    Vehicle-to-vehicle distance control does not operate
    U0122
    U0123
    U0126
    U0293
    (Warning and indicator lights come on)
    Lane keeping assist system
    Driving support ECU
    1. Main body ECU
    2. Skid control ECU
    3. Yaw rate sensor
    4. EPS ECU
    5. Combination meter
    Lane-keeping assist is inoperative
    U0122
    U0123
    U0131
    U1104
    (Warning and indicator lights come on)
    Pre-collision system
    Driving support ECU
    1. Power management control ECU
    2. Skid control ECU
    3. Steering angle sensor
    4. Yaw rate sensor
    5. Seat belt control ECU
    6. Combination meter
    7. Main body ECU
    Pre-collision control is inoperative
    U0122
    U0123
    U0126
    U0142
    U0293
    U1104
    U1100
    (Warning and indicator lights come on)
    Seat belt control ECU
    1. Skid control ECU
    2. Driving support ECU
    3. Center airbag sensor
    4. Main body ECU
    Pre-collision control is inoperative
    U0122
    U0140
    U0151
    U1104
    (Warning and indicator lights come on)

    HINT:
    1. *1: for Navigation receiver type
    2. *2: for Radio and display type