Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR

REAR DOOR > ADJUSTMENT

for Preparation Click here


B228782E01
Text in Illustration 
*1
Centering Bolt
*2
Standard Bolt

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.
  3. Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.
  4. Specified torque for standard bolts is shown in the standard bolt chart (Click here).



1. INSPECT REAR DOOR


  1. Check that the clearance measurements of areas *1 through *15 are within each standard range.


    B227960E01


    Standard Clearance 
    Area
    Measurement
    Area
    Measurement
    *1
    3.57 to 6.57 mm (0.141 to 0.259 in.)
    *2
    6.17 to 9.17 mm (0.243 to 0.361 in.)
    *3
    3.57 to 6.57 mm (0.141 to 0.259 in.)
    *4
    5.97 to 8.97 mm (0.235 to 0.353 in.)
    *5
    4.62 to 7.62 mm (0.182 to 0.300 in.)
    *6
    1.72 to 4.72 mm (0.0677 to 0.186 in.)
    *7
    2.7 to 5.7 mm (0.106 to 0.224 in.)
    *8
    -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
    *9
    2.7 to 5.7 mm (0.106 to 0.224 in.)
    *10
    -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
    *11
    4.15 to 7.15 mm (0.163 to 0.282 in.)
    *12
    2.7 to 5.7 mm (0.106 to 0.224 in.)
    *13
    -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
    *14
    2.8 to 5.8 mm (0.110 to 0.228 in.)
    *15
    -1.3 to 1.7 mm (-0.0512 to 0.0669 in.)
    -
    -



2. ADJUST REAR DOOR

NOTICE:
Make sure to turn the power switch off when adjusting door lock strikers.



    B228897
  1. Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

    SST
    09812-00010  

  1. Tighten the hinge bolts on the vehicle body after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Loosen the hinge bolts on the door and adjust the door position.

  1. Tighten the hinge bolts on the door after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    B228898
  1. Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.

  1. Using a brass bar and a hammer, hit the striker to adjust its position.

  1. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }