Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P3107-214    Lost Communication with Airbag System Control Module

for Preparation Click here


DESCRIPTION

  1. Refer to the description for DTC P3107-213 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3107
214
Open or short to +B in the communication circuit
(1 trip detection logic)
  1. Wire harness or connector
  2. Airbag ECU assembly
  3. Power management control ECU

Related Data List 
DTC No.
Data List
P3107-214
Collision Signal (Airbag)

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 .
Refer to the wiring diagram for DTC P3107-213 .

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 15 seconds or more.

1.CHECK DTC OUTPUT (AIRBAG)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.

  1. Check if DTCs are output.

Result:
Result
Proceed to
Airbag system DTCs are not output.
A
Airbag system DTCs are output.
B

  1. Turn the power switch off.



B
GO TO DTC CHART (Click here)
A


2.CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM)
  1. Turn the power switch on (READY).



    A216762E03
  1. Connect an oscilloscope between the airbag ECU assembly terminals specified in the table below, and measure the waveform.
    Item
    Contents
    Terminal
    L16-14 (GSW2) - L16-25 (E1)
    Equipment Setting
    5V/DIV., 500ms/DIV.
    Condition
    Power switch on (READY)

    Result:
    Result
    Proceed to
    The waveform appears as shown in the illustration.
    A
    The waveform differs from the one shown in the illustration.
    B

    Text in Illustration  
    *1
    Component with harness connected
    (Airbag ECU Assembly)

  1. Turn the power switch off.



B
Go to step 6
A


3.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.


NEXT


4.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3107-214 is not output.
    A
    P3107-214 is output again.
    B

  1. Turn the power switch off.



B
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
A


5.CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems (Click here).



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A216617
  1. Check the connections of the power management control ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG ECU ASSEMBLY CONNECTOR)


    A216765E01
  1. Check the connections of the airbag ECU assembly connectors.
    Text in Illustration 
    *1
    Component with harness connected
    (Airbag ECU Assembly)

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


8.CHECK HARNESS AND CONNECTOR (+B SHORT)


    A243887E01
  1. Remove the IGCT NO. 2 fuse and AM2 fuse from the engine room relay block and junction block assembly.
    Text in Illustration 
    *1
    Engine Room Relay Block and Junction Block Assembly
    *2
    AM2 Fuse
    *3
    IGCT NO. 2 Fuse

  1. Disconnect connector L16 from the airbag ECU assembly.



    A243895E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L5-29 (ABFS) - A21-2 (+B2)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A22-5 (+B1)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L5-1 (AM22)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L6-7 (AM21)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A22-6 (MREL)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A22-1 (IG2)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L6-1 (ACCD)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L6-2 (IG1D)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A22-2 (IG2D)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L5-14 (SPDI)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A21-16 (GI)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A21-4 (FCTL)
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Component with harness connected
    (Power Management Control ECU)

  1. Connect the airbag ECU assembly connector.

  1. Install the IGCT NO. 2 fuse and AM2 fuse.



NG
Go to step 11
OK


9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG ECU ASSEMBLY)
  1. Disconnect connector L5 from the power management control ECU.

  1. Disconnect connector L16 from the airbag ECU assembly.



    A216764E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    L5-29 (ABFS) - L16-14 (GSW2)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    L5-29 (ABFS) or L16-14 (GSW2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *2
    Rear view of wire harness connector
    (to Airbag ECU Assembly)

    HINT:
    As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.

  1. Connect the airbag ECU assembly connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK POWER MANAGEMENT CONTROL ECU
  1. Disconnect connector L16 from the airbag ECU assembly.

  1. Turn the power switch on (IG).



    A204441E34
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L5-29 (ABFS) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Component with harness connected
    (Power Management Control ECU)

    NOTICE:
    Turning the power switch on (IG) with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Connect the airbag ECU assembly connector.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

11.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)


    A243887E01
  1. Remove the IGCT NO. 2 fuse and AM2 fuse from the engine room relay block and junction block assembly.
    Text in Illustration 
    *1
    Engine Room Relay Block and Junction Block Assembly
    *2
    AM2 Fuse
    *3
    IGCT NO. 2 Fuse

  1. Disconnect connector L16 from the airbag ECU assembly.

  1. Disconnect all the connectors from the power management control ECU.



    A238662E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L5-29 (ABFS) - A21-2 (+B2)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A22-5 (+B1)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L5-1 (AM22)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L6-7 (AM21)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A22-6 (MREL)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A22-1 (IG2)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L6-1 (ACCD)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L6-2 (IG1D)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A22-2 (IG2D)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - L5-14 (SPDI)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A21-16 (GI)
    Power switch off
    10 kΩ or higher
    L5-29 (ABFS) - A21-4 (FCTL)
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the power management control ECU connectors.

  1. Connect the airbag ECU assembly connector.

  1. Install the IGCT NO. 2 fuse and AM2 fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)