Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

SMART KEY SYSTEM (for Start Function) > TERMINALS OF ECU

for Preparation Click here



CHECK POWER MANAGEMENT CONTROL ECU

C146689E17

  1. Disconnect the A22, L5 and L6 connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A22-2 (IG2D) - Body ground
    V - Body ground
    IG2 relay operation signal
    Always
    131 to 230 Ω
    A22-23 (STP) - Body ground
    L - Body ground
    Stop light switch signal
    Brake pedal depressed
    11 to 14 V
    A22-23 (STP) - Body ground
    L - Body ground
    Stop light switch signal
    Brake pedal released
    Below 1 V
    L5-1 (AM22) - Body ground
    W - Body ground
    +B power supply
    Always
    9.5 to 16 V
    L6-7 (AM21) - Body ground
    W - Body ground
    +B power supply
    Always
    9.5 to 16 V
    L5-6 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    L6-24 (CA1L) - Body ground
    W - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    L6-25 (CA1H) - Body ground
    B - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    L6-17 (SSW2) - Body ground
    Y - Body ground
    Power switch signal
    Power switch pushed
    Below 1 Ω
    L6-17 (SSW2) - Body ground
    Y - Body ground
    Power switch signal
    Power switch not pushed
    10 kΩ or higher
    L5-7 (SSW1) - Body ground
    B - Body ground
    Power switch signal
    Power switch pushed
    Below 1 Ω
    L5-7 (SSW1) - Body ground
    B - Body ground
    Power switch signal
    Power switch not pushed
    10 kΩ or higher
    L6-1 (ACCD) - Body ground
    G - Body ground
    ACC relay operation signal
    Always
    50.625 to 61.875 Ω
    L6-2 (IG1D) - Body ground
    B - Body ground
    IG1 relay operation signal
    Always
    50.625 to 61.875 Ω
    L6-11 (LIN2) - Body ground
    L - Body ground
    LIN communication line
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the A22, L5 and L6 connectors.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A22-2 (IG2D) - L5-6 (E1)
    V - BR
    IG2 signal
    Power switch on (IG)
    Output voltage at terminal AM21 or AM22 is -2 V or more
    A22-2 (IG2D) - L5-6 (E1)
    V - BR
    IG2 signal
    Power switch on (ACC)
    Below 1 V
    L5-9 (INDW) - L5-6 (E1)
    G - BR
    Warning signal
    Brake pedal depressed, park (P) selected, power switch on (ACC, IG)
    8 to 14 V
    A22-22 (PCON) - L5-6 (E1)
    LG - BR
    P position signal
    Park (P) selected
    Pulse generation
    (See waveform 1)
    A22-28 (PPOS) - L5-6 (E1)
    W - BR
    P position signal
    Park (P) selected
    Pulse generation
    (See waveform 1)
    L6-17 (SSW2) - L5-6 (E1)
    Y - BR
    Power switch signal
    Power switch not pushed
    Output voltage at terminal AM21 or AM22 is -2 V or more
    L6-17 (SSW2) - L5-6 (E1)
    Y - BR
    Power switch signal
    Power switch pushed
    Below 1 V
    L5-7 (SSW1) - L5-6 (E1)
    B - BR
    Power switch signal
    Power switch not pushed
    Output voltage at terminal AM21 or AM22 is -2 V or more
    L5-7 (SSW1) - L5-6 (E1)
    B - BR
    Power switch signal
    Power switch pushed
    Below 1 V
    L6-1 (ACCD) - L5-6 (E1)
    G - BR
    ACC signal
    Power switch on (ACC)
    Output voltage at terminal AM21 or AM22 is -2 V or more
    L6-1 (ACCD) - L5-6 (E1)
    G - BR
    ACC signal
    Power switch off
    Below 1 V
    L6-2 (IG1D) - L5-6 (E1)
    B - BR
    IG1 signal
    Power switch on (IG)
    Output voltage at terminal AM21 or AM22 is -2 V or more
    L6-2 (IG1D) - L5-6 (E1)
    B - BR
    IG1 signal
    Power switch on (ACC)
    Below 1 V
    L5-8 (INDS) - L5-6 (E1)
    R - BR
    Vehicle condition signal
    Brake pedal depressed, park (P) selected
    8 to 14 V
    L5-14 (SPDI) - L5-6 (E1)
    V - BR
    Vehicle speed signal
    Power switch on (IG), wheel rotated slowly
    Pulse generation
    (See waveform 2)
    L6-20 (IMO) - L5-6 (E1)
    L - BR
    Immobiliser communication status
    Immobiliser communicating
    Pulse generation
    (See waveform 3)
    L6-21 (IMI) - L5-6 (E1)
    R - BR
    Immobiliser communication status
    Immobiliser communicating
    Pulse generation
    (See waveform 4)
    If the result is not as specified, the ECU may have a malfunction.



  5. Using an oscilloscope, check the signal waveform of the ECU.



      C236203E01
    1. Waveform 1
      Tester Connection
      CH1: A22-22 (PCON) - L5-6 (E1)
      CH2: A22-28 (PPOS) - L5-6 (E1)
      Tool Setting
      10 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Power switch on (IG)



    2. I042329E01
    3. Waveform 2
      Tester Connection
      L5-14 (SPDI) - L5-6 (E1)
      Tool Setting
      5 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Driving at approx. 20 km/h (12 mph)

      HINT:
      The wavelength becomes shorter as the vehicle speed increases.



    4. B229710E02
    5. Waveform 3
      Tester Connection
      L6-20 (IMO) - L5-6 (E1)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Vehicle Condition
      Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected



    6. B229709E01
    7. Waveform 4
      Tester Connection
      L6-21 (IMI) - L5-6 (E1)
      Tool Setting
      5 V/DIV., 50 ms./DIV.
      Vehicle Condition
      Power switch on (IG)


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B203498E18

  1. Disconnect the L62 connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-1 (+B) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    L62-9 (CANH) - Body ground
    BE - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    L62-10 (CANL) - Body ground
    P - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    L62-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L62-16 (IG) - Body ground
    BE - Body ground
    IG power supply
    Power switch on (IG)
    11 to 14 V
    L62-29 (LIN) - Body ground
    L - Body ground
    LIN communication line
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L62 connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-34 (EFII) - L62-15 (E)*1
    L - W-B
    Immobiliser communication status
    Immobiliser communicating
    Pulse generation
    (See waveform 1)
    L62-35 (EFIO) - L62-15 (E)*1
    R - W-B
    Immobiliser communication status
    Immobiliser communicating
    Pulse generation
    (See waveform 1)

    1. *1: except Canada
    If the result is not as specified, the ECU may have a malfunction.



  5. Using an oscilloscope, check the signal waveform of the ECU.



      A111594E02
    1. Waveform 1
      Tester Connection
      CH1: L62-34 (EFII) - L62-15 (E)
      CH2: L62-35 (EFIO) - L62-15 (E)
      Tool Setting
      5 V/DIV., 200 ms./DIV.
      Vehicle Condition
      Power switch off → Power switch on (IG) → Power switch on (READY)


CHECK TRANSMISSION CONTROL ECU ASSEMBLY

B231382E01

  1. Disconnect the A23 and A24 connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A24-1 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    A24-5 (E02) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    A24-6 (E01) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    A23-16 (+B) - Body ground
    L - Body ground
    Ignition power supply
    Power switch on (IG)
    11 to 14 V
    A23-16 (+B) - Body ground
    L - Body ground
    Ignition power supply
    Power switch off
    Below 1 V
    A23-15 (BATT) - Body ground
    SB - Body ground
    +B power supply
    Except power switch on (READY)
    11 to 14 V
    A23-15 (BATT) - Body ground
    SB - Body ground
    +B power supply
    Power switch on (READY)
    11 to 15.5 V
    A24-15 (CA1L) - Body ground
    BR - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    A24-16 (CA1H) - Body ground
    Y - Body ground
    CAN communication line
    Always
    10 kΩ or higher
    A24-24 (LIN) - Body ground
    L - Body ground
    LIN communication line
    Always
    10 kΩ or higher

    1. If the result is not as specified, there may be a malfunction in the wire harness.


CHECK ID CODE BOX (IMMOBILISER CODE ECU) [for Canada]

B118534E21

  1. Disconnect the L10 connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L10-1 (+B) - L10-8 (GND)
    B - W-B
    +B power supply
    Always
    11 to 14 V
    L10-8 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L10-3 (LIN1) - Body ground
    L - Body ground
    LIN communication line
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L10 ID code box (immobiliser code ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L10-5 (EFII) - L10-8 (GND)
    L - W-B
    Power management control ECU (HV CPU) output signal
    Power switch off
    11 to 14 V
    L10-5 (EFII) - L10-8 (GND)
    L - W-B
    Power management control ECU (HV CPU) output signal
    Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected
    Pulse generation
    (See waveform 1)
    L10-6 (EFIO) - L10-8 (GND)
    R - W-B
    Power management control ECU (HV CPU) input signal
    Power switch off
    Below 1 V
    L10-6 (EFIO) - L10-8 (GND)
    R - W-B
    Power management control ECU (HV CPU) input signal
    Power switch on (IG)
    Pulse generation
    (See waveform 2)

    1. If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.



  5. Inspect using an oscilloscope.



      B229710E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      L10-5 (EFII) - L10-8 (GND)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected



    2. B229709E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      L10-6 (EFIO) - L10-8 (GND)
      Tool Setting
      5 V/DIV., 50 ms./DIV.
      Condition
      Power switch on (IG)