SMART KEY SYSTEM (for Start Function) > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light Switch1 | Stop light switch 1/ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| Start Switch1 | Start switch 1/ON or OFF | ON: Power switch pushed OFF: Power switch not pushed | - |
| Start Switch2 | Start switch 2/ON or OFF | ON: Power switch pushed OFF: Power switch not pushed | - |
| Latch Circuit | Latch circuit/ON or OFF | ON: Power switch on (IG) or on (READY) OFF: Power switch off or on (ACC) | - |
| IG1 Relay Monitor (Outside) | IG1 outer relay monitor/ON or OFF | ON: Power switch on (IG) OFF: Power switch off | - |
| IG1 Relay Monitor (Inside) | IG1 inner relay monitor/ON or OFF | ON: Power switch on (IG) OFF: Power switch off | - |
| IG2 Relay Monitor (Outside) | IG2 outer relay monitor/ON or OFF | ON: Power switch on (IG) OFF: Power switch off | - |
| IG2 Relay Monitor (Inside) | IG2 inner relay monitor/ON or OFF | ON: Power switch on (IG) OFF: Power switch off | - |
| Starter Request Signal | Starter request signal monitor/ON or OFF | ON: ST relay on OFF: ST relay off | - |
| ACC Relay Monitor | ACC relay monitor/ON or OFF | ON: Power switch on (ACC) OFF: Power switch off | - |
| Ready Signal | Status of the ready signal/ON or OFF | ON: Hybrid control system on (on (READY)) OFF: Hybrid control system off | - |
| Vehicle Speed Signal | Vehicle speed signal/Stop or Run | Stop: Vehicle stopped Run: Vehicle running | - |
| Shift P Signal Pulse | Status of the shift P signal pulse/Unknown, Error2, Normal2, Error1, Normal3, Error3 or Normal1 | Unknown: Other Error2: Signal abnormal and park (P) selected Normal2: Signal normal and park (P) selected Error1: Signal abnormal and park (P) state cannot be determined Normal3: Signal normal and R, N, D or B selected Error3: Signal abnormal and R, N, D or B selected Normal1: Signal normal and park (P) state cannot be determined | - |
| Power Supply Condition | Power supply condition/All OFF, ACC ON, IG1 ON, IG2 ON, ST ON | All OFF: All relays off ACC ON: ACC relay on IG1 ON: IG1 relay on IG2 ON: IG2 relay on ST ON: ST request signal on | - |
| Powertrain Type | Status of the powertrain type/HV-AT, Conventional-AT, Conventional-MT, Conventional-MMT | HV-AT | - |
| IG1 Circuit | Status of the IG1 relay activation circuit/OK or NG | OK: IG1 relay activation circuit normal NG: IG1 relay activation circuit abnormal | - |
| IG2 Circuit | Status of the IG2 relay activation circuit/OK or NG | OK: IG2 relay activation circuit normal NG: IG2 relay activation circuit abnormal | - |
| Starter Switch Signal Mismatch | Power switch error detection/No or Yes | No: Power switch error not detected Yes: Power switch error detected | - |
| Park Signal Mismatch | Status of the park signal mismatch/No or Yes | No: Park signal mismatch no detected Yes: Park signal mismatch detected | - |
| Key Certification Waiting Timed Out | Key certification error detection/No or Yes | No: Key certification error not detected Yes: Key certification error detected | - |
| Number of Diagnosis Code | Number of diagnosis code/Min.: 0, MAX.: 255 | Number of DTCs will be displayed | - |
Enter the following menus: Body Electrical / Smart Key / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | Power switch/ON or OFF | ON: Power switch on (IG) OFF: Power switch off | - |
| Key Low Battery | Low key battery/Yes or No | Yes: Key battery voltage low No: Key battery voltage normal | - |
| # Code | Number of DTC recorded/Min.: 0, Max.: 225 | Number of DTCs displayed | - |
| Steering Lock Sleep Cond | Transmission control ECU sleep condition/Yes or No | Yes: Transmission control ECU sleep mode can be entered No: Transmission control ECU sleep mode cannot be entered | - |
| Steering Lock Start Cond | Transmission control ECU start signal/Yes or No | Yes: Transmission control ECU sent a start signal No: Transmission control ECU did not send a start signal | - |
| Engine Start Condition | Hybrid control system start condition/OK or NG | OK: Hybrid control system allowed to start NG: Hybrid control system not allowed to start | - |
| Engine Start Request | Start request condition signal/OK or NG | OK: Start request condition signal received NG: Start request condition signal not received | - |
| 3bit Code Request | Status of the 3-bit code request/OK or NG | OK: 3-bit code request signal received NG: 3-bit code request signal not received | - |
| S Code Check | S code certification result/OK or NG | OK: Certification confirmed NG: Certification not confirmed | - |
| L Code Check | L code certification result/OK or NG | OK: Certification confirmed NG: Certification not confirmed | - |
| Unlock Request Receive | Status of the gearshift control unlock request receive/OK or NG | OK: Gearshift control unlock request signal received NG: Gearshift control unlock request signal not received | - |
| Lock Request Receive | Status of the gearshift control lock request receive/OK or NG | OK: Gearshift control lock request signal received NG: Gearshift control lock request signal not received | - |
| S Code Check (Past) | S code certification result (Past)/OK or NG | OK: Certification confirmed (past) NG: Certification not confirmed (past) | - |
| L Code Check (Past) | L code verification result (Past)/OK or NG | OK: Certification confirmed (past) NG: Certification not confirmed (past) | - |
| EFI Code Receive | SFI communication (when DTC stored)/OK or NG | OK: SFI code received NG: SFI code not received | - |
| EFI Communication | SFI communication /OK or NG | OK: SFI communication normal NG: SFI communication abnormal | - |
| Ignition Available Area | Ignition available area/Front or All | Customization status displayed | - |
| ACTIVE TEST |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Power Source Control / Active Test.
Perform the Active Test according to the display on the Techstream.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Indicator Condition | Power switch indicator | Green/Red/No Sig | Power switch on (READY) |
Enter the following menus: Body Electrical / Smart Key/ Active Test.
Perform the Active Test according to the display on the Techstream.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power / Engine SW Light | Power switch illumination | ON/OFF | Operate with power switch on (IG) and the vehicle stopped. |