Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TIRE PRESSURE WARNING ECU

HINT:
Inspect the connectors from the back side while the connectors are connected.


E129452E39

  1. Disconnect the R2 tire pressure warning antenna and receiver connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L4-12 (RDA) - Body ground
    B - Body ground
    Tire pressure warning antenna and receiver signal
    Power switch on (IG)
    11 to 14 V

  3. Connect the R2 tire pressure warning antenna and receiver connector.

  4. Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may have a malfunction.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L4-1 (CLSW) - Body ground
    Y -Body ground
    Tire pressure warning reset switch
    1. Power switch on (IG)
    2. Tire pressure warning reset switch ON
    8.5 to 15 V
    1. Power switch on (IG)
    2. Tire pressure warning reset switch OFF
    Below 1.5 V
    L4-2 (SPD) - Body ground
    V - Body ground
    Vehicle speed signal
    Vehicle running
    Pulse generation (see waveform 1)
    L4-3 (TC) - Body ground
    L - Body ground
    TC terminal
    Terminal TC not connected
    11 to 14 V
    L4-4 (TACH) - Body ground
    L - Body ground
    RSSI (receive signal strength indication) signal
    Power switch on (IG)
    Pulse generation (see waveform 2)
    L4-5 (IND) - Body ground
    G - Body ground
    Tire pressure warning light output signal
    1. Power switch on (IG)
    2. Tire pressure warning light OFF
    Below 0.5 V
    Tire pressure warning reset switch
    After turning power switch on (IG), tire pressure warning light illuminates for 3 seconds
    0.9 to 3.2 V
    L4-6 (RF5V) - Body ground
    R - Body ground
    Tire pressure warning antenna and receiver power source
    Power switch on (IG)
    11 to 14 V
    L4-7 (IG) - Body ground
    B - Body ground
    IG power source
    Power switch on (IG)
    11 to 14 V
    L4-9 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L4-10 (SIL) - Body ground
    P - Body ground
    Diagnostic communication
    Power switch on (IG)
    8 to 14 V
    L4-11 (GND2) - Body ground
    G - Body ground
    Tire pressure warning antenna and receiver ground
    Always
    Below 1 Ω



  5. F047507E05
  6. Using an oscilloscope, check the waveform 1.
    Waveform 1: 
    Item
    Contents
    Terminal
    L4-2 (SPD) - Body ground
    Tool setting
    5 V/DIV, 20 ms./DIV.
    Vehicle condition
    Driving at approximately 20 km/h (12 mph)

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.



  7. C210231E01
  8. Using an oscilloscope, check the waveform 2.
    Waveform 2: 
    Item
    Contents
    Terminal
    L4-4 (TACH) - Body ground
    Tool setting
    0.5 V/DIV., 10 ms./DIV.
    Vehicle condition
    Power switch on (IG)

    HINT:
    The shape of waves like figure appears approximately 2 times every 3 minutes.