Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

SMART KEY SYSTEM (for Entry Function) > TERMINALS OF ECU

for Preparation Click here



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Disconnect the L62 certification ECU (smart key ECU assembly) connector.


    B203498E17

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-1 (+B) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    L62-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L62-17 (CUTB) - Body ground
    Y - Body ground
    Dark current cut fuse pin input signal
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L62 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-3 (CLG1) - L62-15 (E)
    G - W-B
    Door electrical key oscillator (for driver side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    No pulse generation
    L62-3 (CLG1) - L62-15 (E)
    G - W-B
    Door electrical key oscillator (for driver side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. All doors locked by wireless lock function
    Pulse generation
    L62-4 (CG1B) - L62-15 (E)
    R - W-B
    Door electrical key oscillator (for driver side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    No pulse generation
    L62-4 (CG1B) - L62-15 (E)
    R - W-B
    Door electrical key oscillator (for driver side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. All doors locked by wireless lock function
    Pulse generation
    L62-5 (CLG2) - L62-15 (E)*
    G - W-B
    Door electrical key oscillator (for front passenger side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    No pulse generation
    L62-5 (CLG2) - L62-15 (E)*
    G - W-B
    Door electrical key oscillator (for front passenger side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. All doors locked by wireless lock function
    Pulse generation
    L62-6 (CG2B) - L62-15 (E)*
    R - W-B
    Door electrical key oscillator (for front passenger side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    No pulse generation
    L62-6 (CG2B) - L62-15 (E)*
    R - W-B
    Door electrical key oscillator (for front passenger side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. All doors locked by wireless lock function
    Pulse generation
    L62-7 (CLG5) - L62-15 (E)
    G - W-B
    Indoor electrical key oscillator (for front floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) not touched
    No pulse generation
    L62-7 (CLG5) - L62-15 (E)
    G - W-B
    Indoor electrical key oscillator (for front floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) touched
    Pulse generation
    L62-8 (CG5B) - L62-15 (E)
    R - W-B
    Indoor electrical key oscillator (for front floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) not touched
    No pulse generation
    L62-8 (CG5B) - L62-15 (E)
    R - W-B
    Indoor electrical key oscillator (for front floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) touched
    Pulse generation
    L62-16 (IG) - Body ground
    BE - Body ground
    IG power supply
    Power switch off
    Below 1 V
    L62-16 (IG) - Body ground
    BE - Body ground
    IG power supply
    Power switch on (IG)
    11 to 14 V
    L62-18 (TSW1) - L62-15 (E)
    B - W-B
    Lock sensor (for driver side) detection signal
    1. Power switch off
    2. All doors closed
    3. Lock sensor (for driver side) not touched
    Pulse generation
    L62-18 (TSW1) - L62-15 (E)
    B - W-B
    Lock sensor (for driver side) detection signal
    1. Power switch off
    2. All doors closed
    3. Lock sensor (for driver side) touched
    Below 2 V
    L62-19 (TSW2) - L62-15 (E)*
    B - W-B
    Lock sensor (for front passenger side) detection signal
    1. Power switch off
    2. All doors closed
    3. Lock sensor (for front passenger side) not touched
    Pulse generation
    L62-19 (TSW2) - L62-15 (E)*
    B - W-B
    Lock sensor (for front passenger side) detection signal
    1. Power switch off
    2. All doors closed
    3. Lock sensor (for front passenger side) touched
    Below 2 V
    L62-20 (SEN1) - L62-15 (E)
    Y - W-B
    Touch sensor (for driver side) detection signal
    1. Power switch off
    2. All doors closed
    3. Key not in detection area
    4. Touch sensor (for driver side) not touched
    Pulse generation
    L62-20 (SEN1) - L62-15 (E)
    Y - W-B
    Touch sensor (for driver side) detection signal
    1. Power switch off
    2. All doors closed
    3. Key not in detection area
    4. Touch sensor (for driver side) touched
    Below 2 V
    L62-21 (SEN2) - L62-15 (E)*
    Y - W-B
    Touch sensor (for front passenger side) detection signal
    1. Power switch off
    2. All doors closed
    3. Key not in detection area
    4. Touch sensor (for front passenger side) not touched
    Pulse generation
    L62-21 (SEN2) - L62-15 (E)*
    Y - W-B
    Touch sensor (for front passenger side) detection signal
    1. Power switch off
    2. All doors closed
    3. Key not in detection area
    4. Touch sensor (for front passenger side) touched
    Below 2 V
    L62-22 (TSW5) - L62-15 (E)*
    GR - W-B
    Back door opener switch assembly (opener switch) signal
    Back door opener switch assembly (opener switch) not pushed
    Pulse generation
    L62-22 (TSW5) - L62-15 (E)*
    GR - W-B
    Back door opener switch assembly (opener switch) signal
    Back door opener switch assembly (opener switch) pushed
    Below 1 V
    L62-23 (TSW6) - L62-15 (E)*
    LG - W-B
    Back door opener switch assembly (lock switch) signal
    Back door opener switch assembly (lock switch) not pushed
    Pulse generation
    L62-23 (TSW6) - L62-15 (E)*
    LG - W-B
    Back door opener switch assembly (lock switch) signal
    Back door opener switch assembly (lock switch) pushed
    Below 1 V
    L62-24 (CLG6) - L62-15 (E)
    GR - W-B
    Indoor electrical key oscillator (for center floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) not touched
    No pulse generation
    L62-24 (CLG6) - L62-15 (E)
    GR - W-B
    Indoor electrical key oscillator (for center floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) touched
    Pulse generation
    L62-25 (CG6B) - L62-15 (E)
    BR - W-B
    Indoor electrical key oscillator (for center floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) not touched
    No pulse generation
    L62-25 (CG6B) - L62-15 (E)
    BR - W-B
    Indoor electrical key oscillator (for center floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) touched
    Pulse generation
    L62-26 (CLG7) - L62-15 (E)
    G - W-B
    Indoor electrical key oscillator (for rear floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) not touched
    No pulse generation
    L62-26 (CLG7) - L62-15 (E)
    G - W-B
    Indoor electrical key oscillator (for rear floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) touched
    Pulse generation
    L62-27 (CG7B) - L62-15 (E)
    R - W-B
    Indoor electrical key oscillator (for rear floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) not touched
    No pulse generation
    L62-27 (CG7B) - L62-15 (E)
    R - W-B
    Indoor electrical key oscillator (for rear floor) sensor signal
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) touched
    Pulse generation
    L62-32 (POS1) - L62-15 (E)
    L - W-B
    Lock or unlock sensor (for driver side) output signal
    Power switch off
    9 to 14 V
    L62-32 (POS1) - L62-15 (E)
    L - W-B
    Lock or unlock sensor (for driver side) output signal
    Power switch on (IG)
    Below 2 V
    L62-33 (POS2) - L62-15 (E)*
    L - W-B
    Lock or unlock sensor (for front passenger side) output signal
    Power switch off
    9 to 14 V
    L62-33 (POS2) - L62-15 (E)*
    L - W-B
    Lock or unlock sensor (for front passenger side) output signal
    Power switch on (IG)
    Below 2 V
    L63-5 (RC0) - L62-15 (E)
    R - W-B
    Door control receiver power source
    1. Power switch off
    2. Lock or unlock switch on key not pushed
    Below 1 V
    L63-5 (RC0) - L62-15 (E)
    R - W-B
    Door control receiver power source
    1. Power switch off
    2. Lock or unlock switch on key pushed
    4.5 to 5.5 V
    L63-15 (RDA) - L62-15 (E)
    Y - W-B
    Door control receiver data input signal
    1. Power switch off
    2. All doors closed
    3. Transmitter switch not pressed
    11 to 14 V pulse generation at regular intervals
    L63-15 (RDA) - L62-15 (E)
    Y - W-B
    Door control receiver data input signal
    1. Power switch off
    2. All doors closed
    3. Transmitter switch pressed
    Pulse generation
    L63-16 (RSSI) - L62-15 (E)
    V - W-B
    Door control receiver electric wave existence signal
    1. Power switch off
    2. All doors locked
    3. Lock or unlock switch on key not pushed
    11 to 14 V
    L63-16 (RSSI) - L62-15 (E)
    V - W-B
    Door control receiver electric wave existence signal
    1. Power switch off
    2. All doors locked
    3. Lock or unlock switch on key pushed
    Below 2 V
    L63-19 (CLG8) - L62-15 (E)*
    G - W-B
    Outside electrical key oscillator (for rear side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Back door opener switch assembly off
    No pulse generation
    L63-19 (CLG8) - L62-15 (E)*
    G - W-B
    Outside electrical key oscillator (for rear side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Back door opener switch assembly on
    Pulse generation
    L63-20 (CG8B) - L62-15 (E)*
    R - W-B
    Outside electrical key oscillator (for rear side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Back door opener switch assembly off
    No pulse generation
    L63-20 (CG8B) - L62-15 (E)*
    R - W-B
    Outside electrical key oscillator (for rear side) sensor signal
    1. Power switch off
    2. All doors closed
    3. Back door opener switch assembly on
    Pulse generation

    1. *: w/ Entry System Back Door Open Function
    If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


  1. Disconnect the 2B and 2C junction block connectors.


    B231709E13


    Text in Illustration 
    *A
    Main body ECU (multiplex network body ECU) with 3 connectors
    -
    -
    *1
    Main body ECU (multiplex network body ECU)
    *2
    3 connectors

    E192848E15


    Text in Illustration 
    *A
    Main body ECU (multiplex network body ECU) with 1 connector
    -
    -
    *1
    Main body ECU (multiplex network body ECU)
    *2
    1 connector

  2. Disconnect the A and L8 main body ECU connector.

  3. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-6 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    2C-18 (BECU) - Body ground
    Y - Body ground
    Battery power supply
    Power switch off
    11 to 14 V
    L8-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Power switch on (ACC)
    11 to 14 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Power switch off
    Below 1 V
    A-31 (ALTB) - Body ground
    -
    Battery power supply
    Power switch off
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Power switch power supply
    Power switch on (IG)
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Power switch power supply
    Power switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the 2B and 2C junction block connectors.

  5. Reconnect the A main body ECU connector.

  6. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2B-1 (ACT-) - Body ground
    B - Body ground
    Door lock motor unlock drive output (except driver side)
    Driver or front passenger side door control switch off
    Below 1 V
    2B-1 (ACT-) - Body ground
    B - Body ground
    Door lock motor unlock drive output (except driver side)
    Driver or front passenger side door control switch unlocked
    11 to 14 V
    2B-8 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (all doors)
    Driver or front passenger side door control switch off
    Below 1 V
    2B-8 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (all doors)
    Driver or front passenger side door control switch locked
    11 to 14 V
    2B-5 (ACTD) - Body ground
    B - Body ground
    Driver side door lock motor unlock drive output
    Driver or front passenger side door control switch off
    Below 1 V
    2B-5 (ACTD) - Body ground
    B - Body ground
    Driver side door lock motor unlock drive output
    Driver or front passenger side door control switch unlocked
    11 to 14 V
    2D-36 (FRCY) - Body ground
    BR - Body ground
    Front passenger side door courtesy switch input
    Front passenger side door open
    Below 1 V
    2D-36 (FRCY) - Body ground
    BR - Body ground
    Front passenger side door courtesy switch input
    Front passenger side door closed
    11 to 14 V
    2D-35 (FLCY) - Body ground
    V - Body ground
    Driver side door courtesy switch input
    Driver door open
    Below 1 V
    2D-35 (FLCY) - Body ground
    V - Body ground
    Driver side door courtesy switch input
    Driver door closed
    11 to 14 V
    2D-25 (LSR) - Body ground
    GR - Body ground
    Rear door LH lock position switch input
    Rear door LH unlocked
    Below 1 V
    2D-25 (LSR) - Body ground
    GR - Body ground
    Rear door LH lock position switch input
    Power switch off, all doors closed and rear door LH locked
    11 to 14 V
    2B-29 (LSR) - Body ground
    GR - Body ground
    Rear door RH lock position switch input
    Rear door RH unlocked
    Below 1 V
    2B-29 (LSR) - Body ground
    GR - Body ground
    Rear door RH lock position switch input
    Power switch off, all doors closed and rear door RH locked
    11 to 14 V
    L7-6 (LRCY) - Body ground
    G - Body ground
    Rear door courtesy light switch input
    Rear door open
    Below 1 V
    L7-6 (LRCY) - Body ground
    G - Body ground
    Rear door courtesy light switch input
    Rear door closed
    11 to 14 V
    L7-7 (LSFL) - Body ground
    GR - Body ground
    Driver door lock position switch input
    Driver door unlocked
    Below 1 V
    L7-7 (LSFL) - Body ground
    GR - Body ground
    Driver door lock position switch input
    Power switch off, all doors closed and driver door locked
    11 to 14 V
    L7-9 (L1) - Body ground
    LG - Body ground
    Front passenger side door control switch input
    Front passenger side door control switch locked
    Below 1 V
    L7-9 (L1) - Body ground
    LG - Body ground
    Front passenger side door control switch input
    Front passenger side door control switch off
    11 to 14 V
    L7-10 (UL1) - Body ground
    BR - Body ground
    Front passenger side door control switch input
    Front passenger side door control switch unlocked
    Below 1 V
    L7-10 (UL1) - Body ground
    BR - Body ground
    Front passenger side door control switch input
    Front passenger side door control switch off
    11 to 14 V
    L7-11 (L2) - Body ground
    G - Body ground
    Driver door key-linked lock input
    Driver door key cylinder turned to lock
    Below 1 V
    L7-11 (L2) - Body ground
    G - Body ground
    Driver door key-linked lock input
    Driver door key cylinder off
    11 to 14 V
    L7-18 (LSFR) - Body ground
    LG - Body ground
    Front passenger side door lock position switch input
    Front passenger side door unlocked
    Below 1 V
    L7-18 (LSFR) - Body ground
    LG - Body ground
    Front passenger side door lock position switch input
    Power switch off, all doors closed and front passenger side door locked
    11 to 14 V
    L7-19 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    L7-19 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door closed
    11 to 14 V
    L7-23 (BDSU) - Body ground*1
    GR - Body ground
    Back door opener switch input
    Back door opener switch pushed
    Below 1 V
    L7-23 (BDSU) - Body ground*1
    GR - Body ground
    Back door opener switch input
    Back door opener switch not pushed
    11 to 14 V
    L7-24 (UL3) - Body ground
    V - Body ground
    Driver door key-linked unlock input
    Driver door key cylinder turned to unlock
    Below 1 V
    L7-24 (UL3) - Body ground
    V - Body ground
    Driver door key-linked unlock input
    Driver door key cylinder off
    11 to 14 V

    1. *1: w/o Entry System Back Door Open Function
    If the result is not as specified, the main body ECU (multiplex network body ECU) may have a malfunction.


COMBINATION METER ASSEMBLY


  1. Disconnect the L27 combination meter assembly connector.


    E165864E02

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L27-18 (B) - Body ground
    R - Body ground
    Battery
    Power switch off
    11 to 14 V
    L27-30 (ES) - Body ground
    BR - Body ground
    Ground (Signal ground)
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L27 combination meter assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L27-19 (IG+) - Body ground
    L - Body ground
    Power switch signal
    Power switch off
    Below 1 V
    L27-19 (IG+) - Body ground
    L - Body ground
    Power switch signal
    Power switch on (IG)
    11 to 14 V
    If the result is not as specified, the combination meter assembly may have a malfunction.