Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. Turn the power switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the power switch off before inspecting CAN bus wires for a ground short.
  3. After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
  5. This section describes the standard CAN values for all CAN related components.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


CAN NO. 1 JUNCTION CONNECTOR


  1. Check the CAN No. 1 junction connector.



    1. Connection diagram


      C200970E28


      Text in Illustration 
      *1
      Front view of wire harness connector (to CAN No. 1 Junction Connector)
      *2
      to Combination Meter
      *3
      to Steering Angle Sensor
      *4
      to Main Body ECU
      *5
      to Power Steering ECU
      *6
      to DLC3
      *7
      1. to Navigation ECU Sub-assembly*1*2
      2. to Radio and Display Receiver Assembly*2
      *8
      to CAN No. 2 Junction Connector
      *9
      to Yaw Rate Sensor
      *10
      to Certification ECU
      *11
      to Skid Control ECU
      -
      -
      *1: for Navigation receiver type
      *2: for Radio and display type

  2. Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

    Terminal No. (Symbol)
    Wiring Color
    Connected to
    L94-1 (CANH)
    P
    Combination meter
    L94-12 (CANL)
    W
    L94-2 (CANH)
    L
    Steering angle sensor
    L94-13 (CANL)
    W
    L94-3 (CANH)
    BR
    Main body ECU
    L94-14 (CANL)
    W
    L94-4 (CANH)
    R
    Power steering ECU
    L94-15 (CANL)
    W
    L94-5 (CANH)
    W
    DLC3
    L94-16 (CANL)
    Y
    L94-6 (CANH)
    G
    1. Navigation ECU Sub-assembly*1*2
    2. Radio and display receiver assembly*2
    L94-17 (CANL)
    W
    L94-7 (CANH)
    V
    CAN No. 2 junction connector
    L94-18 (CANL)
    W
    L94-8 (CANH)
    Y
    Yaw rate sensor
    L94-19 (CANL)
    L
    L94-9 (CANH)
    BE
    Certification ECU
    L94-20 (CANL)
    P
    L94-10 (CANH)
    LG
    Skid Control ECU
    L94-21 (CANL)
    L
    *1: for Navigation receiver type
    *2: for Radio and display type


CAN NO. 2 JUNCTION CONNECTOR


  1. Check the CAN No. 2 junction connector.



    1. Connection diagram


      C200970E29


      Text in Illustration 
      *1
      Front view of wire harness connector (to CAN No. 2 Junction Connector)
      *2
      to CAN No. 1 Junction Connector
      *3
      to Center Airbag Sensor Assembly
      *4
      to Transmission Control ECU
      *5
      to Power Management Control ECU
      *6
      to ECM

  2. Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

    Terminal No. (Symbol)
    Wiring Color
    Connected to
    L95-3 (CANH)
    V
    CAN No. 1 junction connector
    L95-14 (CANL)
    W
    L95-5 (CANH)
    R
    Center airbag sensor assembly
    L95-16 (CANL)
    G
    L95-7 (CANH)
    Y
    Transmission control ECU
    L95-18 (CANL)
    BR
    L95-8 (CANH)
    B
    Power management control ECU
    L95-19 (CANL)
    W
    L95-9 (CANH)
    P
    ECM
    L95-20 (CANL)
    V


CAN NO. 3 JUNCTION CONNECTOR


  1. Check the CAN No. 3 junction connector.



    1. Connection diagram


      C252630E01


      Text in Illustration 
      *1
      CAN No. 3 Junction Connector
      *2
      Junction Connector B Side
      *3
      Junction Connector A Side
      *4
      Earth Terminal
      *5
      Front view of wire harness connector (to CAN No. 3 Junction Connector)
      -
      -

  2. Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

    Terminal No. (Symbol)
    Wiring Color
    Connected to
    L97-1 (CANH)
    P
    Power management control ECU
    L97-2 (CANL)
    V
    L98-1 (CANH)
    LG
    Seat belt control ECU
    L98-2 (CANL)
    L
    L99-1 (CANH)
    B
    Driving support ECU
    L99-2 (CANL)
    W


CAN NO. 4 JUNCTION CONNECTOR


  1. Check the CAN No. 4 junction connector.



    1. Connection diagram


      C200970E30


      Text in Illustration 
      *1
      Front view of wire harness connector (to CAN No. 4 Junction Connector)
      *2
      to Power Management Control ECU
      *3
      to Air Conditioning Amplifier
      *4
      to Skid Control ECU
      *5
      to ECM
      -
      -

  2. Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.

    Terminal No. (Symbol)
    Wiring Color
    Connected to
    L101-12 (CANH)
    LG
    Power management control ECU
    L101-1 (CANL)
    L
    L101-13 (CANH)
    Y
    Air conditioning amplifier
    L101-2 (CANL)
    BR
    L101-14 (CANH)
    P
    Skid control ECU
    L101-3 (CANL)
    V
    L101-15 (CANH)
    B
    ECM
    L101-4 (CANL)
    W


CAN NO. 5 JUNCTION CONNECTOR


  1. Check the CAN No. 5 junction connector.



    1. Connection diagram


      C200970E31


      Text in Illustration 
      *1
      Front view of wire harness connector (to CAN No. 5 Junction Connector)
      *2
      to Millimeter Wave Radar Sensor
      *3
      to Lane Recognition Camera Sensor
      *4
      to Driving Support ECU

  2. Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

    Terminal No. (Symbol)
    Wiring Color
    Connected to
    L102-1 (CANH)
    LG
    Millimeter wave radar sensor
    L102-12 (CANL)
    P
    L102-2 (CANH)
    B
    Lane recognition camera sensor
    L102-13 (CANL)
    W
    L102-3 (CANH)
    Y
    Driving support ECU
    L102-14 (CANL)
    L


DLC3


  1. Measure the resistance according to the value(s) in the table below.


    C188081E07


    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L61-6 (CANH) - L61-14 (CANL)
    W - Y
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L61-6 (CANH) - L61-4 (CG)
    W - G
    HIGH-level CAN bus line - Chassis ground
    Power switch off
    200 Ω or higher
    L61-14 (CANL) - L61-4 (CG)
    Y - G
    LOW-level CAN bus line - Chassis ground
    Power switch off
    200 Ω or higher
    L61-6 (CANH) - L61-16 (BAT)
    W - R
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L61-14 (CANL) - L61-16 (BAT)
    Y - R
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


    Text in Illustration 
    *1
    DLC3


ECM


  1. Disconnect the ECM connectors.


    C188791E10


    Text in Illustration 
    *1
    Front view of wire harness connector (to ECM)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    for CAN No. 1 Bus Main Wire 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A57-13 (CANH) - A57-5 (CANL)
    P - V
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    108 to 132 Ω
    A57-13 (CANH) - D28-104 (E1)
    P - BR
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A57-5 (CANL) - D28-104 (E1)
    V - BR
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A57-13 (CANH) - A57-20 (BATT)
    P - R
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A57-5 (CANL) - A57-20 (BATT)
    V - R
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher

    for Power Management Bus Main Wire 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A57-12 (CANP) - A57-4 (CANN)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    108 to 132 Ω
    A57-12 (CANP) - D28-104 (E1)
    B - BR
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A57-4 (CANN) - D28-104 (E1)
    W - BR
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A57-12 (CANP) - A57-20 (BATT)
    B - R
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A57-4 (CANN) - A57-20 (BATT)
    W - R
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


COMBINATION METER


  1. Disconnect the combination meter connector.


    C188799E06


    Text in Illustration 
    *1
    Front view of wire harness connector (to Combination Meter)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L27-10 (CANH) - L27-11 (CANL)
    P - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    108 to 132 Ω
    L27-10 (CANH) - L27-30 (ES)
    P - BR
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L27-11 (CANL) - L27-30 (ES)
    W - BR
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L27-10 (CANH) - L27-18 (B)
    P - R
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L27-11 (CANL) - L27-18 (B)
    W - R
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


POWER MANAGEMENT CONTROL ECU

C146689E14



  1. CAN No. 1 Bus Branch Wire



      A204446E51
    1. Disconnect the power management control ECU connector.
      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to Power Management Control ECU)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      for CAN No. 1 Bus Branch Wire 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      L6-25 (CA1H) - L6-24 (CA1L)
      B - W
      HIGH-level CAN bus line - LOW-level CAN bus line
      Power switch off
      54 to 69 Ω
      L6-25 (CA1H) - L6-5 (E02)
      B - W-B
      HIGH-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L6-24 (CA1L) - L6-5 (E02)
      W - W-B
      LOW-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L6-25 (CA1H) - L6-7 (AM21)
      B - W
      HIGH-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher
      L6-24 (CA1L) - L6-7 (AM21)
      W - W
      LOW-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher



  2. CAN No. 2 Bus Main Wire



      A204445E02
    1. Disconnect the power management control ECU connector.
      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to Power Management Control ECU)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      for CAN No. 2 Bus Main Wire 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      L5-34 (CA2H) - L5-35 (CA2L)
      P - V
      HIGH-level CAN bus line - LOW-level CAN bus line
      Power switch off
      108 to 132 Ω
      L5-34 (CA2H) - L5-6 (E1)
      P - BR
      HIGH-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L5-35 (CA2L) - L5-6 (E1)
      V - BR
      LOW-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L5-34 (CA2H) - L5-1 (AM22)
      P - W
      HIGH-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher
      L5-35 (CA2L) - L5-1 (AM22)
      V - W
      LOW-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher



  3. Power Management Bus Main Wire



      A204446E52
    1. Disconnect the power management control ECU connector.
      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to Power Management Control ECU)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      for Power Management Bus Main Wire 
      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      L6-31 (CA3P) -L6-30 (CA3N)
      LG - L
      HIGH-level CAN bus line - LOW-level CAN bus line
      Power switch off
      108 to 132 Ω
      L6-31 (CA3P) - L6-5 (E02)
      LG - W-B
      HIGH-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L6-30 (CA3N) - L6-5 (E02)
      L - W-B
      LOW-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L6-31 (CA3P) - L6-7 (AM21)
      LG - W
      HIGH-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher
      L6-30 (CA3N) - L6-7 (AM21)
      L - W
      LOW-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher


MAIN BODY ECU

E192848E03


Text in Illustration 
*1
Instrument Panel Junction Block and Main Body ECU
(except Korea, w/o LED Headlight System and w/o Remote Air Conditioning System)

B231709E03


Text in Illustration 
*2
Instrument Panel Junction Block and Main Body ECU
(for Korea, w/ LED Headlight System or w/ Remote Air Conditioning System)


  1. Disconnect the main body ECU connector.


    C210425E01


    Text in Illustration 
    *3
    Front view of wire harness connector
    (to Main Body ECU)
    *4
    DLC3

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L7-14 (CANH) - L7-13 (CANL)
    BR - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L7-14 (CANH) - L61-4 (CG)
    BR - G
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L7-13 (CANL) - L61-4 (CG)
    W - G
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L7-14 (CANH) - L61-16 (BAT)
    BR - R
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L7-13 (CANL) - L61-16 (BAT)
    W - R
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER)


    C209401E09
  1. Disconnect the skid control ECU (brake booster with master cylinder) connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control ECU)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    for CAN No. 1 Bus Branch Wire 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A58-37 (CA1H) - A58-38 (CA1L)
    LG - L
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    A58-37 (CA1H) - A58-28 (GND)
    LG - W
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A58-38 (CA1L) - A58-28 (GND)
    L - W
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A58-37 (CA1H) - A58-15 (BS)
    LG - B
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A58-38 (CA1L) - A58-15 (BS)
    L - B
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher

    for Power Management Bus Branch Wire 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A58-35 (CA2H) - A58-34 (CA2L)
    P - V
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    A58-35 (CA2H) - A58-28 (GND)
    P - W
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A58-34 (CA2L) - A58-28 (GND)
    V - W
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A58-35 (CA2H) - A58-15 (BS)
    P - B
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A58-34 (CA2L) - A58-15 (BS)
    V - B
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


STEERING ANGLE SENSOR


    C185765E37
  1. Disconnect the steering angle sensor connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Steering Angle Sensor)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L51-4 (CANH) - L51-3 (CANL)
    L - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L51-4 (CANH) - L51-2 (ESS)
    L - W-B
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L51-3 (CANL) - L51-2 (ESS)
    W - W-B
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L51-4 (CANH) - L51-6 (BAT)
    L - R
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L51-3 (CANL) - L51-6 (BAT)
    W - R
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


YAW RATE SENSOR


    C152858E10
  1. Disconnect the yaw rate sensor connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Yaw Rate Sensor)
    *2
    DLC3

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L12-3 (CANH) - L12-2 (CANL)
    Y - L
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L12-3 (CANH) - L12-1 (GND)
    Y - W-B
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L12-2 (CANL) - L12-1 (GND)
    L - W-B
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L12-3 (CANH) - L61-16 (BAT)
    Y - R
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L12-2 (CANL) - L61-16 (BAT)
    L - R
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


POWER STEERING ECU


  1. Disconnect the power steering ECU connectors.


    C188801E05


    Text in Illustration 
    *1
    Front view of wire harness connector (to Power Steering ECU)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L54-1 (CANH) - L54-7 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L54-1 (CANH) - A27-2 (PGND)
    R - W-B
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L54-7 (CANL) - A27-2 (PGND)
    W - W-B
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L54-1 (CANH) - A27-1 (PIG)
    R - W
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L54-7 (CANL) - A27-1 (PIG)
    W - W
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY


  1. Disconnect the center airbag sensor assembly connector.


    C188802E07


    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *2
    DLC3

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L16-13 (CANH) - L16-22 (CANL)
    R - G
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L16-13 (CANH) - L16-25 (E1)
    R - W-B
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L16-22 (CANL) - L16-25 (E1)
    G - W-B
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L16-13 (CANH) - L61-16 (BAT)
    R - R
    CAN communication line H - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L16-22 (CANL) - L61-16 (BAT)
    G - R
    CAN communication line L - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


CERTIFICATION ECU (SMART KEY ECU)


  1. Disconnect the certification ECU connector.


    C201303E03


    Text in Illustration 
    *1
    Front view of wire harness connector (to Certification ECU)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-9 (CANH) - L62-10 (CANL)
    BE - P
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L62-9 (CANH) - L62-15 (E)
    BE - W-B
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L62-10 (CANL) - L62-15 (E)
    P - W-B
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L62-9 (CANH) - L62-1 (+B)
    BE - B
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L62-10 (CANL) - L62-1 (+B)
    P - B
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


TRANSMISSION CONTROL ECU

C208988E01



    C210430E01
  1. Disconnect the transmission control ECU connectors.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Transmission Control ECU)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A24-16 (CA1H) - A24-15 (CA1L)
    Y - BR
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    A24-16 (CA1H) - A24-1 (E1)
    Y - BR
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A24-15 (CA1L) - A24-1 (E1)
    BR - BR
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A24-16 (CA1H) - A23-15 (BATT)
    Y - SB
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A24-15 (CA1L) - A23-15 (BATT)
    BR - SB
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)

C250212E06


Text in Illustration 
*1
for 6 Speakers
*2
for 8 Speakers
*3
w/ Navigation System
-
-


  1. Disconnect the radio and display receiver assembly connectors.


    C277255E01


    Text in Illustration 
    *1
    Front view of wire harness connector (to Radio and Display Receiver Assembly)
    *2
    for 6 Speakers
    *3
    for 8 Speakers
    -
    -

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      L149-9 (CANH) - L149-10 (CANL)*1
      L149-9 (CANH) - L149-10 (CANL)*2
      G - W
      HIGH-level CAN bus line - LOW-level CAN bus line
      Power switch off
      54 to 69 Ω
      L149-9 (CANH) - L146-7 (GND1)*1
      L149-9 (CANH) - L138-20 (GND1)*2
      G - BR
      HIGH-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L149-10 (CANL) - L146-7 (GND1)*1
      L149-10 (CANL) - L138-20 (GND1)*2
      W - BR
      LOW-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L149-9 (CANH) - L148-4 (+B1)*1
      L149-9 (CANH) - L138-1 (+B1)*2
      G - SB
      HIGH-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher
      L149-10 (CANL) - L148-4 (+B1)*1
      L149-10 (CANL) - L138-1 (+B1)*2
      W - SB
      LOW-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher

      1. *1: for 6 Speakers
      2. *2: for 8 Speakers


NAVIGATION ECU SUB-ASSEMBLY (for Navigation Receiver Type)

E225806E17



  1. Disconnect the navigation ECU sub-assembly connectors.


    C240506E18


    Text in Illustration 
    *1
    Front view of wire harness connector (to Navigation ECU Sub-assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      L130-9 (CANH) - L130-10 (CANL)
      G - W
      HIGH-level CAN bus line - LOW-level CAN bus line
      Power switch off
      54 to 69 Ω
      L130-9 (CANH) - L127-7 (GND1)
      G - BR
      HIGH-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L130-10 (CANL) - L127-7 (GND1)
      W - BR
      LOW-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L130-9 (CANH) - L127-4 (+B1)
      G - SB
      HIGH-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher
      L130-10 (CANL) - L127-4 (+B1)
      W - SB
      LOW-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher


NAVIGATION ECU SUB-ASSEMBLY (for Radio and Display Type)

E225806E17



  1. Disconnect the navigation ECU sub-assembly connectors.


    C240506E18


    Text in Illustration 
    *1
    Front view of wire harness connector (to Navigation ECU Sub-assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminal No. (Symbol)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      L130-9 (CANH) - L130-10 (CANL)
      G - W
      HIGH-level CAN bus line - LOW-level CAN bus line
      Power switch off
      54 to 69 Ω
      L130-9 (CANH) - L127-7 (GND1)
      G - BR
      HIGH-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L130-10 (CANL) - L127-7 (GND1)
      W - BR
      LOW-level CAN bus line - Ground
      Power switch off
      200 Ω or higher
      L130-9 (CANH) - L127-4 (+B1)
      G - SB
      HIGH-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher
      L130-10 (CANL) - L127-4 (+B1)
      W - SB
      LOW-level CAN bus line - Auxiliary battery positive (+)
      Cable disconnected from negative (-) auxiliary battery terminal
      6 kΩ or higher


AIR CONDITIONING AMPLIFIER


  1. Disconnect the air conditioning amplifier connector.


    C188799E07


    Text in Illustration 
    *1
    Front view of wire harness connector (to Air Conditioning Amplifier)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L17-11 (CANH) - L17-12 (CANL)
    Y - BR
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L17-11 (CANH) - L17-14 (GND)
    Y - W-B
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L17-12 (CANL) - L17-14 (GND)
    BR - W-B
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L17-11 (CANH) - L17-21 (B)
    Y - Y
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L17-12 (CANL) - L17-21 (B)
    BR - Y
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


SEAT BELT CONTROL ECU (w/ Pre-collision System)

E140518E20



    C210431E01
  1. Disconnect the seat belt control ECU connectors.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Seat Belt Control ECU)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L3-1 (CANH) - L3-2 (CANL)
    LG - L
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L3-1 (CANH) - L2-8 (PGND)
    LG - W-B
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L3-2 (CANL) - L2-8 (PGND)
    L - W-B
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L3-1 (CANH) - L2-7 (+B)
    LG - B
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L3-2 (CANL) - L2-7 (+B)
    L - B
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


DRIVING SUPPORT ECU (w/ Dynamic Radar Cruise Control System)
E178930E17
  1. Disconnect the driving support ECU connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Driving Support ECU)

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    CAN No. 2 Bus Branch Wire 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L60-39 (CA2H) - L60-17 (CA2L)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    L60-39 (CA2H) - L60-25 (GND)
    B - W-B
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L60-17 (CA2L) - L60-25 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L60-39 (CA2H) - L60-30 (B)
    B - B
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L60-17 (CA2L) - L60-30 (B)
    W - B
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


    Standard Resistance:

    Parking Assist Bus Main Wire 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L60-40 (CA1P) - L60-18 (CA1N)
    Y - L
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    108 to 132 Ω
    L60-40 (CA1P) - L60-25 (GND)
    Y - W-B
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L60-18 (CA1N) - L60-25 (GND)
    L - W-B
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    L60-40 (CA1P) - L60-30 (B)
    Y - B
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    L60-18 (CA1N) - L60-30 (B)
    L - B
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


MILLIMETER WAVE RADAR SENSOR (w/ Dynamic Radar Cruise Control System)


    C210460E01
  1. Disconnect the millimeter wave radar sensor connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Millimeter Wave Radar Sensor)
    *2
    DLC3

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A2-4 (CA1P) - A2-3 (CA1N)
    LG - P
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    108 to 132 Ω
    A2-4 (CA1P)- L61-4 (CG)
    LG - G
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A2-3 (CA1N) - L61-4 (CG)
    P - G
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    A2-4 (CA1P) - L61-16 (BAT)
    LG - R
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A2-3 (CA1N) - L61-16 (BAT)
    P - R
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


LANE RECOGNITION CAMERA SENSOR (w/ Lane-keeping Assist System)
C210459E01
  1. Disconnect the lane recognition camera sensor connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Lane Recognition Camera Sensor)
    *2
    DLC3

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    U4-1 (CA1P) - U4-2 (CA1N)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Power switch off
    54 to 69 Ω
    U4-1 (CA1P)- L61-4 (CG)
    B - G
    HIGH-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    U4-2 (CA1N) - L61-4 (CG)
    W - G
    LOW-level CAN bus line - Ground
    Power switch off
    200 Ω or higher
    U4-1 (CA1P) - L61-16 (BAT)
    B - R
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    U4-2 (CA1N) - L61-16 (BAT)
    W - R
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher