Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P1606-308    Collision has been detected or Collision Sensor Connection (Open)

DTC    P1606-317    Collision has been detected or Collision Sensor Connection (Open)

for Preparation Click here


DESCRIPTION

The power management control ECU receives a signal that indicates a collision from the airbag sensor assembly to detect a collision. After detecting a collision, the power management control ECU shuts off the high voltage systems for safety.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P1606
308
Collision detection
A block signal is received from the airbag sensor assembly.
(1 trip detection logic)
  1. Airbag sensor assembly
  2. Power management control ECU
  3. Supplemental restraint systems
P1606
317
Collision detection
Multiple wiring malfunctions occur simultaneously.
(1 trip detection logic)
  1. Power management control ECU
  2. Supplemental restraint systems

HINT:
If P1606-308 or 317 is output, the vehicle cannot start unless the DTCs are cleared using the Techstream.


Related Data List 
DTC No.
Data List
P1606-308
  1. Collision Signal (Airbag)
  2. Normal Signal for A/B ECU
P1606-317

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 5 seconds or more.

1.CHECK VEHICLE FOR COLLISION DAMAGE
  1. Check the vehicle condition.

    Result:
    Result
    Proceed to
    The vehicle is not damaged.
    A
    The vehicle is damaged.
    B



B
REPAIR VEHICLE
A


2.CHECK DTC OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P1606 only is output.
    A
    P0A1D is output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART (Click here)
A


3.CHECK SUPPLEMENTAL RESTRAINT SYSTEM
  1. Troubleshoot the airbag system (Click here).

    Result:
    Result
    Proceed to
    The system is normal.
    A
    There is a malfunction in the system.
    B



B
REPAIR MALFUNCTIONING PARTS, COMPONENT AND AREA
A


4.CHECK INFORMATION CODE
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Access the freeze frame data of DTC P1606 and read the INF code.

    Result:
    Result
    Proceed to
    INF code 308 is output.
    A
    INF code 317 is output.
    B

  1. Turn the power switch off.



B
Go to step 5
A

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

5.CHECK DTC OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    One or two of the following conditions are met.
    A
    All of the following conditions are met.
    B


    DTC Output Status
    1
    DTC P3107-213 or P3107-214 is output.
    2
    DTC U0151-763 is output.
    3
    DTC U0110-160 or U0110-657 is output.

  1. Turn the power switch off.



B
GO TO DTC CHART (Click here)
A

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)