Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A09-591    DC / DC Converter Status Circuit Low Input

for Preparation Click here


DESCRIPTION

The DC/DC converter varies output voltage based on voltage change signals (VLO signal line) received from the power management control ECU.
If the vehicle is being driven with an inoperative DC/DC converter, the voltage of the auxiliary battery will drop, which will prevent the continued operation of the vehicle. Therefore, the power management control ECU monitors the operation of the DC/DC converter and alerts the driver if it detects a malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A09
591
Open or short to ground in the signal line of DC/DC converter (VLO)
(1 trip detection logic)
  1. Wire harness or connector
  2. Inverter with converter assembly
  3. Power management control ECU

WIRING DIAGRAM


C280808E01


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 10 seconds or more.

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A216617
  1. Check the connections of the power management control ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)
A214648

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

NOTICE:
Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.

  1. Check the connection of the low voltage connector of the inverter with converter assembly.

    OK:
    The connector is connected securely and there are no contact problems.

    HINT:
    When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.



NG
CONNECT SECURELY
OK


3.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
  1. Turn the power switch on (IG).



    A204482E02
  1. Connect an oscilloscope between the power management control ECU terminals specified in the table below, and measure the waveform.
    Item
    Content
    Terminal
    A21-11 (VLO) - L5-6 (E1)
    Equipment Setting
    5V/DIV., 50ms/DIV.
    Condition
    Power switch on (IG)
    Text in Illustration 
    *1
    Component with harness connected
    (Power Management Control ECU)

    OK:
    The waveform appears as shown in the illustration.

    HINT:
    1. Perform this inspection with the power management control ECU connector connected.
    2. The waveform varies depending on the specified DC/DC converter voltage.

  1. Turn the power switch off.



NG
Go to step 6
OK


4.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.


NEXT


5.CHECK DTC OUTPUT (HV)
  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTC P0A09-591 is not output.
    A
    DTC P0A09-591 is output again.
    B

  1. Turn the power switch off.



B
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

6.CHECK POWER MANAGEMENT CONTROL ECU

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A59 from the inverter with converter assembly.



    A215725E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A59-3 (VLO) - Body ground
    Power switch off
    370 to 430 kΩ

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

  1. Connect the inverter with converter assembly connector.



NG
Go to step 7
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect connector A59 from the inverter with converter assembly.

  1. Disconnect connector A21 from the power management control ECU.



    A216618E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A59-3 (VLO) - A21-11 (VLO)
    Power switch off
    Below 1 Ω
    A59-3 (VLO) or A21-11 (VLO) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *2
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the inverter with converter assembly connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)