Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A0F-204    Engine Failed to Start

DTC    P0A0F-205    Engine Failed to Start

DTC    P0A0F-206    Engine Failed to Start

DTC    P0A0F-524    Engine Failed to Start

DTC    P0A0F-525    Engine Failed to Start

for Preparation Click here


DESCRIPTION

If an engine malfunction occurs, an engine malfunction signal is sent from the ECM to the power management control ECU (HV CPU) . When the power management control ECU (HV CPU) receives this signal, it sets a DTC and performs fail-safe control.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A0F
204
Signal indicating abnormality is received from the ECM (abnormal engine output)
Actual engine torque is very low compared to the target torque.
(1 trip detection logic)
SFI system
205
Signal indicating abnormality is received from the ECM (engine unable to start)
(1 trip detection logic)
206
Signal indicating abnormality is received from the ECM (engine component malfunctioning, drop in torque)
(1 trip detection logic)
524
Signal indicating abnormality is received from the ECM (abnormal NE signal)
(1 trip detection logic)
525
Signal indicating abnormality is received from the ECM (abnormal GI signal)
(1 trip detection logic)

Related Data List 
DTC No.
Data List
P0A0F-204
  1. Request Power
  2. Actual Engine Torque (SFI System)
  3. Engine Revolution
  4. Generator(MG1) Torq
  5. Generator(MG1) Rev
P0A0F-205
P0A0F-206
P0A0F-524
Engine Revolution
P0A0F-525
  1. Engine Revolution
  2. Crank Position
The following items can be helpful when performing repairs:
Data List
  1. Ready Signal
  2. State of Charge (All Bat)
  3. +B

HINT:
  1. The power management control ECU stores DTC P0A0F-204, 205, 206, 524 or 525 when it receives a signal from the ECM indicating abnormal engine power, engine starting malfunction, engine performance deterioration (running out of fuel), crank angle sensor circuit DTCs or cam position sensor circuit DTCs.
  2. If the engine cannot start, the vehicle is driven using EV drive mode. However, if the vehicle is continuously driven using only EV drive mode, the HV battery will be discharged and the vehicle will not be able to be driven.
  3. If any of these DTCs are output, it is required to repair the EFI system in accordance with the DTC or to add a sufficient amount of fuel.

    Hybrid control system DTCs
    SFI system related DTCs
    P0A0F-204 (Abnormal engine output)
    P3190 (Poor Engine Power)
    P0A0F-205 (Engine unable to start)
    P3191 (Engine does not Start)
    P0A0F-206 (Engine component malfunctioning, drop in torque)
    P0171 (System Too Lean(Bank 1))
    P0172 (System Too Rich(Bank 1))
    P0606 (ECM / PCM Processor)
    P060E (Internal Control Module Throttle Position Performance)
    P0A0F-524 (Abnormal NE signal)
    P0335 (Crankshaft Position Sensor "A" Circuit)
    P0A0F-525 (Abnormal GI signal)
    P0340 (Camshaft Position Sensor Circuit Malfunction)
    P0342 (Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor))
    P0343 (Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor))


INSPECTION PROCEDURE

HINT:
  1. When SFI system related DTCs are output, the power management control ECU stores DTCs P0A0F-204, 205, 206, 524 or 525.
  2. If DTC P0A0F-524 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. With the vehicle and engine stopped, the power switch on (READY) and park (P) selected, depress the accelerator pedal to start the engine.
    2. Keep the engine running for 5 seconds or more.
  3. If DTC P0A0F-525 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. With the vehicle and engine stopped, the power switch on (READY) and park (P) selected, depress the accelerator pedal to start the engine.
    2. Keep the engine running for 5 seconds or more.

1.CHECK DTC OUTPUT (ENGINE CONTROL SYSTEM)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check if DTCs are output.

  1. Turn the power switch off.


NEXT

GO TO DTC CHART (Click here)