Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A0F-238    Engine Failed to Start

for Preparation Click here


DESCRIPTION

If the power management control ECU (HV CPU) detects that the engine or transmission gear has seized, the power management control ECU (HV CPU) will perform fail-safe control. Also, if a substance or object is preventing the engine or transmission internal components from rotating, the power management control ECU (HV CPU) will perform fail-safe control.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A0F
238
The engine does not start even though it is being cranked while driving (engine or transmission input components malfunction)
(1 trip detection logic)
  1. Hybrid vehicle transaxle assembly
  2. Transmission input damper assembly
  3. Power management control ECU
  4. Engine

Related Data List 
DTC No.
Data List
P0A0F-238
  1. Engine Revolution
  2. Generator(MG1) Torq
  3. Generator(MG1) Rev
  4. Vehicle Spd
  5. Motor(MG2) Revolution

A217594E01


INSPECTION PROCEDURE

HINT:
  1. A seized engine, mechanical malfunction of the hybrid vehicle transaxle can be suspected.
  2. If this DTC is output, the engine or transmission gear may be seized. Be sure to check the level of the engine oil, automatic transmission fluid (ATF), and coolant before inspection.
  3. After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. While driving the vehicle at a speed of 12 mph (20 km/h) or more in EV mode, depress the accelerator pedal to start the engine, and drive the vehicle for 3 seconds or more.*1
      1. *1: When the HV system is normal, the engine starts when the accelerator pedal is depressed halfway or more. If the HV system is malfunctioning, the engine may not start. Even in this case, if you drive the vehicle at a speed of 12 mph (20 km/h) or more in EV mode for 3 seconds or more, you can confirm this DTC.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Only DTC P0A0F-238 is output or any DTCs other than P0A1D are also output.
    A
    P0A0F-238 and P0A1D (hybrid vehicle control ECU circuit malfunction) are output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART (Click here)
A


2.CHECK CRANKSHAFT PULLEY REVOLUTION (PARK (P) SELECTED)
  1. Push the P position switch.

  1. Lift up the vehicle.

  1. Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

    CAUTION:
    Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.

    NOTICE:
    Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.

    OK:
    The crankshaft rotates smoothly.



NG
Go to step 7
OK


3.CLEAR DTC (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


4.CHECK ENGINE RACING
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Push the P position switch.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Generator (MG1) Rev, Engine Revolution.

  1. Read the Data List.

  1. Turn the power switch on (READY).



    A212091E01
  1. While the READY indicator is on, fully depress the accelerator pedal for 10 seconds.

    OK:
    Generator (MG1) Rev increases to approximately 3.6 times that of Engine Revolution.

    HINT:
    1. If the engine does not race and DTC P3147-239 (Transmission system) is output or generator (MG1) operates but the engine does not crank, replace the hybrid vehicle transaxle assembly.
    2. Refer to the graph for Data List confirmation of "Generator (MG1) Rev" and " Engine Revolution".
      Data List
      ENGINE REV
      MG1 REV
      Reference Value
      Approximately 1000 rpm
      Approximately 3600 rpm
      Approximately 1500 rpm
      Approximately 5400 rpm
      Approximately 2500 rpm
      Approximately 9000 rpm

  1. Turn the power switch off.



NG
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)
OK


5.CHECK CREEP MOVEMENT
  1. Turn the power switch on (READY).

  1. Depress the brake pedal, move the selector lever to D, and release the brake pedal.

    OK:
    The wheels turn (the vehicle creeps forward).

  1. Turn the power switch off.



NG
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)
OK


6.CHECK ENGINE SPEED
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Motor (MG2) Revolution, Generator (MG1) Rev, Engine Revolution.

  1. Read the Data List.

  1. Move the selector lever to D.

  1. Fully depress the accelerator pedal when the vehicle speed is 6 mph (10 km/h) or more.

    NOTICE:
    Perform this test only in an appropriate safe location, in accordance with all local laws.

    OK:
    The difference between Engine Revolution and 0.28 X Generator (MG1) Rev + 0.27 X Motor (MG2) Revolution is 500 rpm or more and it is maintained for 1 second.

    HINT:
    If the engine races to over revolution or DTC P3147-241 (Transmission system) is output, replace the transmission input damper assembly.

  1. Turn the power switch off.



NG
REPLACE TRANSMISSION INPUT DAMPER ASSEMBLY (Click here)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

7.CHECK CRANKSHAFT PULLEY REVOLUTION (SELECTOR LEVER IN N)
  1. Lift up the vehicle.

  1. Turn the power switch on (IG).

  1. Move the selector lever to N.

  1. Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

    CAUTION:
    Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch on (IG) before performing this inspection, to prevent the engine from starting.

    NOTICE:
    Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.

    OK:
    The crankshaft rotates smoothly.



NG
REPAIR OR REPLACE ENGINE
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)