Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A78-510    Drive Motor "A" Inverter Performance

for Preparation Click here


DESCRIPTION

For a description of the inverter, .
If the inverter receives a motor gate shutdown signal from the MG ECU, it will turn all power transistors off which are activating motor to forcibly stop motor operation.
The MG ECU monitors motor gate shutdown signals and detects a malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A78
510
Motor gate shutdown signal malfunction
Current flow to motor is detected even while the inverter is receiving a motor gate shutdown signal
Inverter with converter assembly

Related Data List 
DTC No.
Data List
P0A78-510
  1. MG2 Gate Status
  2. M(MG2) Trg Exec Val

HINT:
  1. When P0A78-510 has been stored, the hybrid system cannot be restarted until the DTC is cleared.
  2. If the problem symptom cannot be reproduced, leaving the vehicle with the power switch on (READY) and neutral (N) selected for 1 minute will make it easier to reproduce the symptom.


MONITOR DESCRIPTION

The MG ECU monitors the current to the MG2. The MG ECU checks if current passes to the MG2 while the vehicle is stopped with power switch on (IG) or the shift lever in N. If current flow is detected in either of these two situations, the power management control ECU (HV CPU) will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A78 (INF 510): Malfunction of inverter gate shutdown circuit
Required sensors / components
Motor inverter
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Power management control ECU (HV CPU)
DTC P0A78 (INF 510) is not detected

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for 30 seconds or more.
  5. Turn the power switch on (READY) and turn the Techstream on.
  6. With the vehicle stopped and park (P) selected, move the shift lever to N, wait for 10 seconds and then push the P position switch.

    NOTICE:
    Do not leave the vehicle for an extended time with neutral (N) selected.

  7. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
  8. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output and want to confirm permanent DTC, perform the following procedure.

  9. Check that permanent DTCs are cleared.
  10. If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch off and wait for 30 seconds or more.
  2. Turn the power switch on (READY).
  3. With the vehicle stopped and park (P) selected, move the shift lever to N, wait for 10 seconds and push the P position switch.

    NOTICE:
    Do not leave the vehicle for an extended time with neutral (N) selected.

1.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)
A214648

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

NOTICE:
Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.

  1. Check the connection of the low voltage connector of the inverter with converter assembly.

    OK:
    The connector is connected securely and there are no contact problems.

    HINT:
    When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.



NG
CONNECT SECURELY
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)