Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A78-586    Drive Motor "A" Inverter Performance

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0A78-266 .
The signal line from the inverter voltage (VH) sensor is connected to the MG ECU inside the inverter with converter assembly. If P0A78-586 is output, replace the inverter with converter assembly.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A78
586
Inverter voltage (VH) sensor performance problem
During inverter voltage does not boosted difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is large and difference between "VH-Voltage after Boosting" and "Power Resource VB" is large.
(1 trip detection logic)
Inverter with converter assembly

Related Data List 
DTC No.
Data List
P0A78-586
  1. VL-Voltage before Boosting
  2. VH-Voltage after Boosting
  3. Power Resource VB

MONITOR DESCRIPTION

The power management control ECU (HV CPU) monitors the inverter voltage (VH) sensor signal. If the power management control ECU (HV CPU) detects a fault in the sensor signal, the power management control ECU (HV CPU) interprets this as a VH sensor failure. The power management control ECU (HV CPU) will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A78 (INF 586): Voltage (VH) sensor deviation
Required sensors / components
Motor inverter
Frequency of operation
-
Duration
TMC's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Power management control ECU (HV CPU)
DTC P0A78 (INF 586) is not detected

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for 30 seconds or more.
  5. Turn the power switch on (READY) and turn the Techstream on.
  6. With drive (D) selected, depress both the accelerator pedal and brake pedal at the same time to raise the SOC to a sufficient level.
  7. Push the P position switch, check that the engine is stopped and move the shift lever to N.
  8. Set the A/C for maximum cooling.
  9. Leave the vehicle for a few minutes.
  10. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
  11. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output and want to confirm permanent DTC, perform the following procedure.

  12. Check that permanent DTCs are cleared.
  13. If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (READY) with park (P) selected.
  2. Confirm that the Data List item "Boost Ratio" is 0 % when the accelerator pedal is not depressed. Check that the Data List items "VH-Voltage after Boosting" and "Power Resource VB" are almost the same.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A78-586 only is output or DTCs except the ones in the table below are also output.
    A
    DTCs shown in Table 1 are output simultaneously.
    B
    DTCs shown in Table 2 are output simultaneously.
    C


    Table 1 
    DTC No.
    Relevant Diagnosis
    P0A1A-151, 155, 156, 658, 659
    Generator Control Module
    P0A1B-164, 193, 512, 661, 786
    Drive Motor "A" Control Module
    P0A1D-148
    Hybrid Powertrain Control Module
    P0A78-266, 267
    Drive Motor "A" Inverter Performance
    P0A94-589, 590
    DC/DC Converter Performance
    P2511-149
    HV CPU Power Relay Sense Circuit Intermittent No Continuity
    P3004-132
    High Voltage Power Resource
    P324E-788
    MG-ECU Power Relay Intermittent Circuit
    U0110 (all INF codes)*1
    Lost Communication with Drive Motor Control Module "A"

    Table 2 
    DTC No.
    Relevant Diagnosis
    P0AFC-123
    Hybrid Battery Pack Sensor Module
    P0B3D-123
    Hybrid Battery Voltage Sensor "A" Circuit Low
    P0B42-123
    Hybrid Battery Voltage Sensor "B" Circuit Low
    P0B47-123
    Hybrid Battery Voltage Sensor "C" Circuit Low
    P0B4C-123
    Hybrid Battery Voltage Sensor "D" Circuit Low
    P0B51-123
    Hybrid Battery Voltage Sensor "E" Circuit Low
    P0B56-123
    Hybrid Battery Voltage Sensor "F" Circuit Low
    P0B5B-123
    Hybrid Battery Voltage Sensor "G" Circuit Low
    P0B60-123
    Hybrid Battery Voltage Sensor "H" Circuit Low
    P0B65-123
    Hybrid Battery Voltage Sensor "I" Circuit Low
    P0B6A-123
    Hybrid Battery Voltage Sensor "J" Circuit Low
    P0B6F-123
    Hybrid Battery Voltage Sensor "K" Circuit Low
    P0B74-123
    Hybrid Battery Voltage Sensor "L" Circuit Low
    P0B79-123
    Hybrid Battery Voltage Sensor "M" Circuit Low
    P0B7E-123
    Hybrid Battery Voltage Sensor "N" Circuit Low
    P0B83-123
    Hybrid Battery Voltage Sensor "O" Circuit Low
    P308A-123
    Hybrid Battery Voltage Sensor All Circuits Low

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
    2. P0A78-586 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)

C
GO TO DTC CHART (HYBRID BATTERY SYSTEM) (Click here)
A

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)