Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P3147-239    Transmission system

DTC    P3147-241    Transmission system

for Preparation Click here


DESCRIPTION

The hybrid vehicle transaxle assembly consists of the power split planetary gear unit, generator, motor, and the 2-stage motor speed reduction planetary gear unit. The power split planetary gear unit uses a planetary gear to split engine output in accordance with driving requests while the vehicle is driven or the HV battery is charged. motor assists engine output while increasing vehicle drive force. motor also converts the energy, which would otherwise be consumed in the form of heat during normal braking, into electrical energy. This recovered energy is put back into the HV battery to perform regenerative braking. generator generates power, which is used for charging the HV battery or driving motor, and also regulates the amount of electricity being generated. In addition, generator is used as a starter motor to start the engine.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3147
239
Drive force from motor (MG2) or the engine cannot be transmitted to the wheels.
The engine, generator (MG1), motor (MG2) or hybrid vehicle transaxle assembly does not run smoothly due to a mechanical malfunction.
(1 trip detection logic)
  1. Engine
  2. Hybrid vehicle transaxle assembly
  3. Wire harness or connector
  4. Power management control ECU
  5. Transmission input damper
P3147
241
Hybrid vehicle transaxle malfunction (input system lock)
When the vehicle is stopped, an engine cranking signal is sent but the generator (MG1) does not rotate. Generator (MG1) or the engine does not rotate, or the planetary gear unit is malfunctioning.
(1 trip detection logic)

Related Data List 
DTC No.
Data List
P3147-239
  1. Motor(MG2) Revolution
  2. Motor(MG2) Torq
  3. M(MG2) Trq Exec Val
  4. Generator(MG1) Rev
  5. Generator(MG1) Torq
  6. G(MG1) Trq Exec Val
  7. Engine Revolution
  8. Calculate Load
P3147-241
The following items can be helpful when performing repairs:
Data List
  1. Ready Signal
  2. Vehicle Spd
  3. Accelerator Degree
  4. Shift Sensor Shift Pos

INSPECTION PROCEDURE

HINT:
  1. If DTC P3147-239 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Drive the vehicle at approximately 12 mph (30 km/h) or more for approximately 5 seconds or more using the engine.
  2. If DTC P3147-241 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. With the vehicle stopped and the park (P) selected, turn the power switch on (READY) and gradually depress the accelerator pedal so that the engine starts.

1.CHECK DTC OUTPUT (ENGINE CONTROL SYSTEM)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Engine control system DTCs are not output.
    A
    Engine control system DTCs are output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART (SFI SYSTEM) (Click here)
A


2.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTCs other than P3147-239 or P3147-241 are not output.
    A
    DTC P3147-240 or P3147-242 is also output.
    B
    DTC P0A1D is also output.
    C

  1. Turn the power switch off.



B
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)

C
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A


3.CHECK CRANKSHAFT PULLEY REVOLUTION (PARK (P) SELECTED)
  1. Turn the power switch off.

  1. Push the P position switch and lift up the vehicle.

  1. Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

    CAUTION:
    Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.

    NOTICE:
    Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.

    Result:
    Result
    Proceed to
    The crankshaft rotates.
    A
    The crankshaft does not rotate.
    B



B
Go to step 8
A


4.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


5.CHECK ENGINE RACING
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Push the P position switch.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Generator (MG1) Rev, Engine Revolution.

  1. Read the Data List.

  1. Turn the power switch on (READY).



    A212091E01
  1. While the READY indicator is on, fully depress the accelerator pedal for 10 seconds.

    OK:
    Generator (MG1) Rev increases to approximately 3.6 times that of Engine Revolution.

    HINT:
    1. If the engine does not race and DTC P3147-239 (Transmission system) is output or generator (MG1) operates but the engine does not crank, replace the hybrid vehicle transaxle assembly.
    2. Refer to the graph for Data List confirmation of "Generator (MG1) Rev" and " Engine Revolution".
      Data List
      ENGINE REV
      MG1 REV
      Reference Value
      Approximately 1000 rpm
      Approximately 3600 rpm
      Approximately 1500 rpm
      Approximately 5400 rpm
      Approximately 2500 rpm
      Approximately 9000 rpm

  1. Turn the power switch off.



NG
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)
OK


6.CHECK CREEP MOVEMENT
  1. Depress the brake pedal, move the shift lever to D, and release the brake pedal.

    OK:
    The wheels turn (the vehicle creeps forward).

    HINT:
    If the wheels do not turn and the reading on the Techstream shows DTC P3147-239, replace the hybrid vehicle transaxle assembly.



NG
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)
OK


7.CHECK ENGINE SPEED
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Motor (MG2) Revolution, Generator (MG1) Rev, Engine Revolution.

  1. Read the Data List.

  1. Move the selector lever to D.

  1. Fully depress the accelerator pedal when the vehicle speed is 6 mph (10 km/h) or more.

    NOTICE:
    Perform this test only in an appropriate safe location, in accordance with all local laws.

    OK:
    The difference between Engine Revolution and 0.28 X Generator (MG1) Rev + 0.27 X Motor (MG2) Revolution is 500 rpm or more and it is maintained for 1 second.

    HINT:
    If the engine races to over revolution or DTC P3147-241 (Transmission system) is output, replace the transmission input damper assembly.

  1. Turn the power switch off.



NG
REPLACE TRANSMISSION INPUT DAMPER ASSEMBLY (Click here)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

8.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
  1. Turn the power switch on (IG) and move the shift lever to N.

  1. Lift up the vehicle.

  1. Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

    CAUTION:
    Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch on (IG) before performing this inspection, to prevent the engine from starting.

    NOTICE:
    Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.

    OK:
    The crankshaft rotates.



NG
REPAIR OR REPLACE ENGINE
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)