DTC P3004-800 High Voltage Power Resource |
DTC P3004-801 High Voltage Power Resource |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P3004 | 800 | High-voltage circuit malfunctions between the HV battery and inverter with converter assembly. Excessive overcurrent occurs during precharge (time from when SMRP turns on until SMRG turns on). (1 trip detection logic) |
|
| P3004 | 801 | High-voltage circuit malfunctions between the HV battery and inverter with converter assembly. Minimal overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on). (1 trip detection logic) |
| DTC No. | Data List |
| P3004-800 |
|
| P3004-801 |
| 1.CHECK DTC OUTPUT (HV) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| P3004-800or P3004-801 only is output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
| P0A09-265 | DC/DC Converter Status Circuit Low Input |
| P0A10-263 | DC/DC Converter Status Circuit High Input |
Turn the power switch off.
|
| ||||
| A | |
| 2.CHECK DTC OUTPUT (HV) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| P3004-800or P3004-801 only is output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
| P0ABF-123 | Hybrid Battery Pack Current Sensor Circuit |
| P0AC0-123 | Hybrid Battery Pack Current Sensor Circuit Range / Performance |
| P0AC1-123 | Hybrid Battery Pack Current Sensor Circuit Low |
| P0AC2-123 | Hybrid Battery Pack Current Sensor Circuit High |
| P0AFC-123 | Hybrid Battery Pack Sensor Module |
| P0B3D-123 | Hybrid Battery Voltage Sensor "A" Circuit Low |
| P0B42-123 | Hybrid Battery Voltage Sensor "B" Circuit Low |
| P0B47-123 | Hybrid Battery Voltage Sensor "C" Circuit Low |
| P0B4C-123 | Hybrid Battery Voltage Sensor "D" Circuit Low |
| P0B51-123 | Hybrid Battery Voltage Sensor "E" Circuit Low |
| P0B56-123 | Hybrid Battery Voltage Sensor "F" Circuit Low |
| P0B5B-123 | Hybrid Battery Voltage Sensor "G" Circuit Low |
| P0B60-123 | Hybrid Battery Voltage Sensor "H" Circuit Low |
| P0B65-123 | Hybrid Battery Voltage Sensor "I" Circuit Low |
| P0B6A-123 | Hybrid Battery Voltage Sensor "J" Circuit Low |
| P0B6F-123 | Hybrid Battery Voltage Sensor "K" Circuit Low |
| P0B74-123 | Hybrid Battery Voltage Sensor "L" Circuit Low |
| P0B79-123 | Hybrid Battery Voltage Sensor "M" Circuit Low |
| P0B7E-123 | Hybrid Battery Voltage Sensor "N" Circuit Low |
| P0B83-123 | Hybrid Battery Voltage Sensor "O" Circuit Low |
| P308A-123 | Hybrid Battery Voltage Sensor All Circuits Low |
| U029A-123 | Lost Communication with Hybrid Battery Pack Sensor Module |
Turn the power switch off.
|
| ||||
| A | |
| 3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR) |
![]() |
Check the connections of the power management control ECU connectors.
|
| ||||
| OK | |
| 4.CHECK COMPRESSOR WITH MOTOR ASSEMBLY |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Disconnect the No. 2 engine wire (air conditioning harness) E3 from the inverter with converter assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E3-1 (ACPB) - E3-2 (ACPE) | Power switch off | 100 kΩ or higher |
| *1 | No. 2 Engine Wire (Air Conditioning Harness) |
| *2 | Shielded Wire Ground |
Connect the No. 2 engine wire (air conditioning harness) to the inverter with converter assembly.
Install the inverter terminal cover to the inverter with converter assembly.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER) |
Disconnect connector A59 from the inverter with converter assembly.
Disconnect connector A21 from power management control ECU.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A21-21 (NODD) - A59-12 (NODD) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| A21-21 (NODD) or A59-12 (NODD) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *1 | Rear view of wire harness connector (to Power Management Control ECU) |
| *2 | Front view of wire harness connector (to Inverter with Converter Assembly) |
Connect the power management control ECU connector.
Connect the inverter with converter assembly connector.
|
| ||||
| OK | |
| 6.CHECK POWER MANAGEMENT CONTROL ECU (NODD) |
Check that the service plug grip is not installed.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A21-21(NODD) - L5-6(E1) | Power switch on (IG) | Less than 1.5 V |
| *a | Component with harness connected (Power Management Control ECU) |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
|
| ||||
| OK | |
| 7.CHECK FRAME WIRE |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Disconnect the frame wire (high voltage DC connector) T1 from the inverter with converter assembly.
Remove the upper hybrid battery cover sub-assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| T3-1 (CEI) - T4-1 (CBI) | Power switch off | 10 kΩ or higher |
Install the upper hybrid battery cover sub-assembly (Click here).
Connect the frame wire (high voltage DC connector) to inverter with converter assembly.
Install the inverter terminal cover to the inverter with converter assembly.
|
| ||||
| OK | ||
| ||
| 8.CHECK NO. 2 ENGINE WIRE |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Disconnect the No. 2 engine wire (air conditioning harness) E3 from the inverter with converter assembly.
![]() |
Disconnect the No. 2 engine wire (air conditioning harness) E1 from the compressor with motor assembly.
| *1 | Green Lock |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E3-1 (ACPB) - E3-2 (ACPE) | Power switch off | 10 kΩ or higher |
| *1 | No. 2 Engine Wire (Air Conditioning Harness) |
| *2 | Shielded Wire Ground |
Connect the No. 2 engine wire (air conditioning harness) E1 to the compressor with motor assembly.
Connect the No. 2 engine wire (air conditioning harness) E3 to the inverter with converter assembly.
Install the inverter terminal cover to the inverter with converter assembly.
|
| ||||
| OK | ||
| ||
| 9.CHECK HYBRID BATTERY JUNCTION BLOCK |
Check that the service plug grip is not installed.
Remove the upper hybrid battery cover sub-assembly (Click here).
![]() |
Disconnect the frame wire T3 and T4 from the hybrid battery junction block.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| T3-1 (CEI) - T4-1 (CBI) | Power switch off | 10 kΩ or higher |
| *1 | Hybrid Battery Junction Block |
Connect the frame wire to the hybrid battery junction block.
Install the upper hybrid battery cover sub-assembly (Click here).
|
| ||||
| OK | ||
| ||