Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Headlight Dimmer Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) receives the following switch information:
  1. Light control switch position is off (DRL OFF), tail, head or AUTO (DRL)
  2. Dimmer switch position is high, low or high flash (pass)
  3. Front fog light switch position is on or off

WIRING DIAGRAM


E241408E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the display on the Techstream.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Dimmer Hi SW
    Dimmer switch high position signal/ON or OFF
    ON: Dimmer switch in high or high flash (pass) position
    OFF: Dimmer switch in low position
    -
    Passing Light SW
    Dimmer switch high flash (pass) position signal/ON or OFF
    ON: Dimmer switch in high flash (pass) position
    OFF: Dimmer switch not in high flash (pass) position
    -
    Front Fog Light SW
    Front fog light switch signal/ON or OFF
    ON: Front fog light switch on
    OFF: Front fog light switch off
    -
    Light Auto SW
    Light control switch AUTO*1 or DRL*2 position signal/ON or OFF
    ON: Light control switch in AUTO*1 or DRL*2 position
    OFF: Light control switch not in AUTO*1 or DRL*2 position
    -
    Headlight SW
    Light control switch head position signal/ON or OFF
    ON: Light control switch in head position
    OFF: Light control switch not in head position
    -
    Taillight SW
    Light control switch tail position signal/ON or OFF
    ON: Light control switch in tail or head position
    OFF: Light control switch in neither tail nor head position
    -

    1. *1: w/ Automatic Light Control
    2. *2: Light control switch w/ DRL position

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY

HINT:
Inspect the items that did not change as a result of monitoring the Data List.



    B162671E42
  1. Remove the headlight dimmer switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Light Control Switch (w/ Automatic Light Control) 
    Tester Connection
    Switch Condition
    Specified Condition
    18 (T) - 12 (EL)
    Light control switch off or DRL OFF
    10 kΩ or higher
    19 (A) - 12 (EL)
    Light control switch off or DRL OFF
    10 kΩ or higher
    20 (H) - 12 (EL)
    Light control switch off or DRL OFF
    10 kΩ or higher
    18 (T) - 12 (EL)
    Light control switch in tail position
    Below 1 Ω
    18 (T) - 12 (EL)
    Light control switch in head position
    Below 1 Ω
    20 (H) - 12 (EL)
    Light control switch in head position
    Below 1 Ω
    19 (A) - 12 (EL)
    Light control switch in AUTO position
    Below 1 Ω
    Light Control Switch (w/o Automatic Light Control) 
    Tester Connection
    Switch Condition
    Specified Condition
    18 (T) - 12 (EL)
    Light control switch off
    10 kΩ or higher
    19 (A) - 12 (EL)*1
    Light control switch off
    10 kΩ or higher
    20 (H) - 12 (EL)
    Light control switch off
    10 kΩ or higher
    18 (T) - 12 (EL)
    Light control switch in tail position
    Below 1 Ω
    18 (T) - 12 (EL)
    Light control switch in head position
    Below 1 Ω
    20 (H) - 12 (EL)
    Light control switch in head position
    Below 1 Ω
    19 (A)*1 - 12 (EL)
    Light control switch in DRL position
    Below 1 Ω
    Dimmer Switch 
    Tester Connection
    Switch Condition
    Specified Condition
    11 (HU) - 12 (EL)
    Dimmer switch in low position
    10 kΩ or higher
    11 (HU) - 12 (EL)
    Dimmer switch in high position
    Below 1 Ω
    17 (HF) - 12 (EL)
    Dimmer switch in high flash position
    Below 1 Ω
    Front Fog Light Switch*2 
    Tester Connection
    Switch Condition
    Specified Condition
    4 (BFG) - 3 (LFG)
    Fog light switch off
    10 kΩ or higher
    4 (BFG) - 3 (LFG)
    Fog light switch on
    Below 1 Ω

    1. *1: w/ Light control switch w/ DRL position
    2. *2: w/ Front Fog Light

    OK:
    Headlight dimmer switch assembly is normal.

    Text in Illustration 
    *1
    Component without harness connected
    (Headlight Dimmer Switch Assembly)



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT DIMMER SWITCH ASSEMBLY)
  1. Disconnect the L47 headlight dimmer switch assembly connector.

  1. Disconnect the L7 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L47-4 (BFG)*1 - L7-27 (FFOG)*1
    Always
    Below 1 Ω
    L47-11 (HU) - L7-5 (HU)
    Always
    Below 1 Ω
    L47-17 (HF) - L7-8 (HF)
    Always
    Below 1 Ω
    L47-18 (T) - L7-30 (TAIL)
    Always
    Below 1 Ω
    L47-19 (A)*2 - L7-28 (A)*2
    Always
    Below 1 Ω
    L47-20 (H) - L7-29 (HEAD)
    Always
    Below 1 Ω
    L47-4 (BFG)*1 - Body ground
    Always
    10 kΩ or higher
    L47-11 (HU) - Body ground
    Always
    10 kΩ or higher
    L47-17 (HF) - Body ground
    Always
    10 kΩ or higher
    L47-18 (T) - Body ground
    Always
    10 kΩ or higher
    L47-19 (A)*2 - Body ground
    Always
    10 kΩ or higher
    L47-20 (H) - Body ground
    Always
    10 kΩ or higher
    L47-12 (EL) - Body ground
    Always
    Below 1 Ω
    L47-3 (LFG)*1 - Body ground
    Always
    Below 1 Ω

    1. *1: w/ Front Fog Light
    2. *2: w/ Automatic Light Control



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)