LIGHTING SYSTEM > Door Courtesy Switch Circuit |

| 1.READ VALUE USING TECHSTREAM |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the display on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Door Courtesy SW | Rear door courtesy light switch RH signal/ON or OFF | ON: Rear door LH or RH open OFF: Rear door LH and RH closed | - |
| RL Door Courtesy SW | Rear door courtesy light switch LH signal/ON or OFF | ON: Rear door LH or RH open OFF: Rear door LH and RH closed | - |
| Back Door Courtesy SW | Back door courtesy switch signal/ON or OFF | ON: Back door open OFF: Back door closed | - |
| FR Door Courtesy | Front door courtesy light switch RH signal/ON or OFF | ON: Front door RH open OFF: Front door RH closed | - |
| FL Door Courtesy | Front door courtesy light switch LH signal/ON or OFF | ON: Front door LH open OFF: Front door LH closed | - |
| Result | Proceed to |
| OK | A |
| Front door courtesy light switch LH or RH does not operate | B |
| Rear door courtesy light switch LH or RH does not operate | C |
| Back door courtesy switch does not operate | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH) |
![]() |
Remove the front door courtesy light switch assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Switch body | Pushed | 10 kΩ or higher |
| 1 - Switch body | Not pushed | Below 1 Ω |
| *1 | Component without harness connected (Front Door Courtesy Light Switch Assembly) |
| *2 | Switch Body |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SWITCH) |
for Front LH
Disconnect the 2D instrument panel junction block assembly connector.
Disconnect the R6 front door courtesy light switch assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2D-35 - R6-1 | Always | Below 1 Ω |
| 2D-35 - Body ground | Always | 10 kΩ or higher |
for Front RH
Disconnect the 2D instrument panel junction block assembly connector.
Disconnect the S5 front door courtesy light switch assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2D-36 - S5-1 | Always | Below 1 Ω |
| 2D-36 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
![]() |
for Front LH
Remove the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2D-35 - A-2 (FLCY) | Always | Below 1 Ω |
| 2D-35 - Body ground | Always | 10 kΩ or higher |
| *1 | Component without harness connected (Instrument Panel Junction Block Assembly) |
![]() |
for Front RH
Remove the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2D-36 - A-4 (FRCY) | Always | Below 1 Ω |
| 2D-36 - Body ground | Always | 10 kΩ or higher |
| *1 | Component without harness connected (Instrument Panel Junction Block Assembly) |
|
| ||||
| OK | ||
| ||
| 5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH) |
![]() |
Remove the rear door courtesy light switch assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Switch body | Pushed | 10 kΩ or higher |
| 1 - Switch body | Not pushed | Below 1 Ω |
| *1 | Component without harness connected (Rear Door Courtesy Light Switch Assembly) |
| *2 | Switch Body |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR COURTESY LIGHT SWITCH) |
for Rear LH
Disconnect the L7 main body ECU (multiplex network body ECU) connector.
Disconnect the R13 rear door courtesy light switch assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L7-6 (LRCY) - R13-1 | Always | Below 1 Ω |
| L7-6 (LRCY) - Body ground | Always | 10 kΩ or higher |
for Rear RH
Disconnect the L7 main body ECU (multiplex network body ECU) connector.
Disconnect the S10 rear door courtesy light switch assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L7-6 (LRCY) - S10-1 | Always | Below 1 Ω |
| L7-6 (LRCY) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.INSPECT BACK DOOR LOCK ASSEMBLY |
![]() |
Remove the back door lock assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (E) - 2 (+) | Locked | 10 kΩ or higher |
| 1 (E) - 2 (+) | Unlocked | Below 1 Ω |
| *1 | Component without harness connected (Back Door Lock Assembly) |
| *2 | Lock |
| *3 | Unlock |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - MAIN BODY ECU) |
Disconnect the L7 main body ECU (multiplex network body ECU) connector.
Disconnect the R18 back door lock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L7-19 (BCTY) - R18-2 (+) | Always | Below 1 Ω |
| L7-19 (BCTY) - Body ground | Always | 10 kΩ or higher |
| R18-1 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||