METER / GAUGE SYSTEM > Fuel Receiver Gauge Malfunction |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL METER OPERATION) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter following menus: Body Electrical / Combination Meter / Active Test.
Check the operation by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Fuel Meter Operation | Fuel receiver gauge | Empty, 1/2, Full | Confirm that the vehicle is stopped with the engine idling |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (FUEL INPUT) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter following menus: Body Electrical / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Fuel Input | Fuel input signal/Min.: 0, Max.: 127.5 | 10th segment comes on: 39.6 to 45.0 | Unit: Liter |
| 9th segment comes on: 35.7 to 39.6 | |||
| 8th segment comes on: 31.8 to 35.7 | |||
| 7th segment comes on: 27.9 to 31.8 | |||
| 6th segment comes on: 24.0 to 27.9 | |||
| 5th segment comes on: 20.1 to 24.0 | |||
| 4th segment comes on: 16.2 to 20.1 | |||
| 3rd segment comes on: 12.3 to 16.2 | |||
| 2nd segment comes on: 8.4 to 12.3 | |||
| 1st segment comes on: 6.1 to 8.4 |
| Result | Proceed to |
| Fuel level data displayed on the Techstream differs from the fuel receiver gauge indication. | A |
| Fuel level data displayed on the Techstream is almost the same as the fuel receiver gauge indication. | B |
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (NO. 3 METER CIRCUIT PLATE - FUEL SENDER GAUGE ASSEMBLY) |
Disconnect the L27 and R11 connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L27-14 (L) - R11-2 (FS) | Always | Below 1 Ω |
| L27-15 (ES2) - R11-3 (FE) | Always | Below 1 Ω |
| L27-14 (L) - Body ground | Always | 10 kΩ or higher |
| L27-15 (ES2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT FUEL SENDER GAUGE ASSEMBLY |
![]() |
Remove the fuel sender gauge assembly (Click here).
Check that the float moves smoothly between F and E.
Check if the fuel sender gauge arm is deformed.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Float level is F (upper) | 13.5 to 16.5 Ω |
| 1 - 2 | Float level is between F (upper) and E (lower) | 13.5 to 414.5 Ω (Gradually changes) |
| 1 - 2 | Float level is E (lower) | 405.5 to 414.5 Ω |
| *1 | Front view of wire harness connector (to Fuel Sender Gauge Assembly) |
|
| ||||
| OK | |
| 5.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) |
Replace the combination meter assembly (meter circuit plate) with a new or a known good one (Click here).
|
| ||||
| OK | ||
| ||
| 6.REPLACE NO. 4 METER CIRCUIT PLATE |
Replace the combination meter assembly (No. 4 meter circuit plate) with a new or a known good one (Click here).
|
| ||||
| OK | ||
| ||