Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



COMBINATION METER ASSEMBLY


  1. Disconnect the L27 combination meter assembly connector.


    B129553E03

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L27-30 (ES) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L27 combination meter assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L27-19 (IG+) - Body ground
    L - Body ground
    Power switch power supply
    Power switch off
    Below 1 V
    L27-19 (IG+) - Body ground
    L - Body ground
    Power switch power supply
    Power switch on (IG)
    11 to 14 V
    L27-21 (PBLT) - Body ground
    Y - Body ground
    Front passenger side seat belt warning light signal
    Power switch on (IG), front passenger side seat occupied, seat belt fastened
    11 to 14 V
    L27-21 (PBLT) - Body ground
    Y - Body ground
    Front passenger side seat belt warning light signal
    Power switch on (IG), front passenger side seat occupied, seat belt unfastened
    Alternates between 11 to 14 V and below 1 V
    If the result is not as specified, the combination meter assembly may have a malfunction.


PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY

B230278E01

  1. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M2-6 (IG+) - Body ground
    L - Body ground
    Power switch power supply
    Power switch on (IG)
    11 to 14 V
    M2-6 (IG+) - Body ground
    L - Body ground
    Power switch power supply
    Power switch off
    Below 1 V
    M2-3 (PBEW) - Body ground
    W - Body ground
    Front passenger side seat belt warning light signal
    Front passenger side seat occupied, seat belt fastened
    11 to 14 V
    M2-3 (PBEW) - Body ground
    W - Body ground
    Front passenger side seat belt warning light signal
    Front passenger side seat occupied, seat belt unfastened
    Alternates between 11 to 14 V and below 1 V

    1. If the result is not as specified, the passenger seat belt warning light assembly may have a malfunction.


CHECK CENTER AIRBAG SENSOR ASSEMBLY

C123353E22


Terminal No.
Terminal Symbol
Destination
S1-12
FSR+
Occupant classification ECU
S1-13
FSR-
Occupant classification ECU
R1-11
LBE+
Front seat inner belt assembly LH
R1-12
LBE-
Front seat inner belt assembly LH

CHECK OCCUPANT CLASSIFICATION ECU

H100909E25

  1. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specification
    W3-1 (+B) - W3-3 (GND)
    W - W-B
    Battery power supply
    Power switch off
    11 to 14 V
    W3-2 (DIA) - W3-3 (GND)
    GR - W-B
    Diagnosis (DLC3)
    Power switch on (IG)
    Pulse generation
    W3-3 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    W3-7 (IG) - W3-3 (GND)
    B - W-B
    Power switch power supply
    Power switch on (IG)
    11 to 14 V
    W3-8 (FSR+) - W3-4 (FSR-)
    L - LG
    Center airbag sensor assembly communication line
    Power switch on (IG)
    Pulse generation
    W3-9 (BSW) - W3-5 (BGND)
    G - P
    Front passenger side buckle switch line
    Always
    Pulse generation
    W2-1 (SGD1) - W3-3 (GND)
    G - W-B
    Front occupant classification sensor LH ground line
    Always
    Below 1 V
    W2-2 (SGD2) - W3-3 (GND)
    LG - W-B
    Front occupant classification sensor RH ground line
    Always
    Below 1 V
    W2-3 (SGD3) - W3-3 (GND)
    W - W-B
    Rear occupant classification sensor LH ground line
    Always
    Below 1 V
    W2-4 (SGD4) - W3-3 (GND)
    BR - W-B
    Rear occupant classification sensor RH ground line
    Always
    Below 1 V
    W2-11 (SVC1) - W2-1 (SGD1)
    R - G
    Front occupant classification sensor LH power supply line
    Power switch on (IG), a load applied to front occupant classification sensor LH
    4.9 to 5.1 V
    W2-12 (SVC2) - W2-2 (SGD2)
    W - LG
    Front occupant classification sensor RH power supply line
    Power switch on (IG), a load applied to front occupant classification sensor RH
    4.9 to 5.1 V
    W2-5 (SVC3) - W2-3 (SGD3)
    GR - W
    Rear occupant classification sensor LH power supply line
    Power switch on (IG), a load applied to rear occupant classification sensor LH
    4.9 to 5.1 V
    W2-6 (SVC4) - W2-4 (SGD4)
    V - BR
    Rear occupant classification sensor RH power supply line
    Power switch on (IG), a load applied to rear occupant classification sensor RH
    4.9 to 5.1 V
    W2-7 (SIG1) - W2-1 (SGD1)
    P - G
    Front occupant classification sensor LH signal line
    Power switch on (IG), a load applied to front occupant classification sensor LH
    0 to 5.1 V
    W2-8 (SIG2) - W2-2 (SGD2)
    L - LG
    Front occupant classification sensor RH signal line
    Power switch on (IG), a load applied to front occupant classification sensor RH
    0 to 5.1 V
    W2-9 (SIG3) - W2-3 (SGD3)
    SB - W
    Rear occupant classification sensor LH signal line
    Power switch on (IG), a load applied to rear occupant classification sensor LH
    0 to 5.1 V
    W2-10 (SIG4) - W2-4 (SGD4)
    B - BR
    Rear occupant classification sensor RH signal line
    Power switch on (IG), a load applied to rear occupant classification sensor RH
    0 to 5.1 V

    1. If the result is not as specified, the occupant classification ECU may have a malfunction.