Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS

BACK DOOR GLASS > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 BACK DOOR GLASS SPACER
  1. Apply Primer G to the installation part of a new No. 2 back door glass spacer.

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.



    B229463E01
  1. Install the new No. 2 back door glass spacer onto the back window fix glass, as shown in the illustration.
    Text in Illustration 
    *1
    Marking for Spacer Pasting

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



2. INSTALL NO. 1 BACK DOOR GLASS SPACER

HINT:
Use the same procedure for the No. 1 spacer and No. 2 spacer.



3. INSTALL NO. 2 BACK WINDOW LOWER MOULDING
  1. Apply Primer G to the installation part of a new No . 2 back window lower moulding.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.



    B229464E02
  1. Install the new back window lower moulding onto the back window fix glass, as shown in the illustration.
    Text in Illustration 
    *1
    Edge of Curved Surface

    Standard Dimension:
    Item
    Dimension
    a
    -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
    b
    5.7 to 8.3 mm (0.224 to 0.326 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



4. INSTALL NO. 2 BACK WINDOW OUTSIDE MOULDING LH
  1. Apply Primer G to the installation part of a new NO. 2 back window outside moulding LH.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.



    B229465E02
  1. Install the new NO. 2 back window outside moulding LH onto the back window fix glass, as shown in the illustration.
    Text in Illustration 
    *1
    Marking for Moulding Pasting

    Standard Dimension:
    Item
    Dimension
    a
    2.0 mm (0.0787 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



5. INSTALL NO. 2 BACK WINDOW OUTSIDE MOULDING RH

HINT:
Use the same procedure for the LH side and RH side.



6. INSTALL NO. 2 BACK DOOR GLASS ADHESIVE DAM
  1. Apply Primer G to the installation part of a new NO. 2 back door glass adhesive dam.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.



    B229466E02
  1. Install the new NO . 2 back door glass adhesive dam onto the back window fix glass, as shown in the illustration.
    Text in Illustration 
    *1
    Marking for Dam Pasting

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



7. INSTALL BACK WINDOW FIX GLASS


  1. Using a brush, coat the installation surface on the vehicle body with Primer M.


    B229462E01


    Text in Illustration 
    *1
    Brush
    *2
    Primer M
    *3
    Adhesive
    -
    -

    NOTICE:
    1. Do not coat the adhesive with Primer M.
    2. Do not apply too much primer.
    3. Allow the primer to dry for 3 minutes or more.
    4. Throw away any leftover primer.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Using a brush or a sponge, coat the application area of the adhesive with Primer G.


    B229467E02

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer to dry for 3 minutes or more.
    3. Throw away any leftover primer.

    HINT:
    1. Apply Primer G onto the ceramic notches.
    2. If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Apply adhesive to the back window fix glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B214800E03
    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      Standard Dimension:
      Item
      Dimension
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all the adhesive within the time described in the table below.

      Usage Time Frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour and 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the back window fix glass as shown in the illustration.


      B229468E02


      Text in Illustration 
      *1
      Ceramic Notch
      -
      -

  1. Install the back window fix glass.

    1. Using suction cups, engage the 2 clips to install the back window fix glass.

      NOTICE:
      1. Check that the clips are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and back window fix glass.

    2. Lightly press the front surface of the back window fix glass to ensure that the back window fix glass is securely fit to the vehicle body.

      HINT:
      Press the back window fix glass with a force of 98 N (10 kgf, 22 lbf) or more.

    3. Using a scraper, remove any excess or protruding adhesive.

      HINT:
      Apply adhesive onto the glass rim.

    4. Hold the back window fix glass using protective tape until applied adhesive becomes hard.

      NOTICE:
      Do not drive the vehicle within the time described in the table below.

      Minimum Time:
      Temperature
      Minimum Time prior to Driving Vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



    B229454
  1. Connect the 2 connectors.



8. INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
  1. for Back Window Fix Glass:

    1. Install the back door outside garnish sub-assembly .



9. INSTALL NO. 2 BACK WINDOW GLASS SPACER
  1. Apply Primer G to the installation part of a new No. 2 back window glass spacer.

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.



    B232004E02
  1. Install the new No. 2 back window glass spacer onto the back door glass, as shown in the illustration.
    Text in Illustration 
    *1
    Edge of Curved Surface
    *2
    Back Window Glass Spacer

    Standard Dimension:
    Item
    Dimension
    a
    69.0 mm (2.716 in.)
    b
    66.1 mm (2.602 in.)
    c
    48.7 mm (1.917 in.)
    d
    49.7 mm (1.956 in.)
    e
    69.9 mm (2.752 in.)
    f
    89.9 mm (3.539 in.)

    NOTICE:
    1. RH and LH spacers are different parts.
    2. Allow the primer to dry for 3 minutes or more.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



10. INSTALL NO. 1 BACK WINDOW GLASS SPACER

HINT:
Use the same procedure for the No. 1 spacer and No. 2 spacer.



11. INSTALL NO .1 BACK WINDOW LOWER MOULDING


    B229493E02
  1. Apply Primer G to the installation part of a new NO. 1 back window lower moulding.

    Standard Dimension:
    Item
    Dimension
    a
    3.0 to 7.0 mm (0.118 to 0.275 in.)

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.



    B229478E02
  1. Install the new NO. 1 back window lower moulding onto the back door glass, as shown in the illustration.
    Text in Illustration 
    *1
    Marking for Moulding Installation

    Standard Dimension:
    Item
    Dimension
    a
    0.3 to 3.3 mm (0.0118 to 0.129 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



12. INSTALL NO. 1 BACK WINDOW OUTSIDE MOULDING LH


    B229492E02
  1. Apply Primer G to the installation part of a new NO. 1 back window outside moulding LH.
    Text in Illustration 
    *1
    Print Mark

    Standard Dimension:
    Item
    Dimension
    a
    8.0 to 12.0 mm (0.315 to 0.472 in.)

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.



    B229479E02
  1. Install the new NO. 1 back window outside moulding LH onto the back door glass, as shown in the illustration.

    Standard Dimension:
    Item
    Dimension
    a
    8.5 to 11.5 mm (0.334 to 0.452 in.)
    b
    4.0 mm (0.157 in.)
    c
    8.0 to 14.0 mm (0.315 to 0.551 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



13. INSTALL NO. 1 BACK WINDOW OUTSIDE MOULDING RH

HINT:
Use the same procedure for the LH side and RH side.



14. INSTALL NO. 1 BACK DOOR GLASS ADHESIVE DAM
  1. Apply Primer G to the installation part of a new NO. 1 back door glass adhesive dam.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.



    B229480E02
  1. Install the new NO. 1 back door glass adhesive dam onto the back door glass, as shown in the illustration.
    Text in Illustration 
    *1
    Marking for Dam Installation

    Standard Dimension:
    Item
    Dimension
    a
    10.2 mm (0.401 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



15. INSTALL BACK DOOR GLASS


  1. Using a brush, coat the installation surface on the vehicle body with Primer M.


    B229481E01


    Text in Illustration 
    *1
    Brush
    *2
    Primer M
    *3
    Adhesive
    -
    -

    NOTICE:
    1. Do not coat the adhesive with Primer M.
    2. Do not apply too much primer.
    3. Allow the primer to dry for 3 minutes or more.
    4. Throw away any leftover primer.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Using a brush or a sponge, coat the application area of the adhesive with Primer G.


    B229482E01


    Text in Illustration 
    *1
    Ceramic Notch
    -
    -

    Standard Dimension:
    Item
    Dimension
    a
    14.0 mm (0.551 in.)

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer to dry for 3 minutes or more.
    3. Throw away any leftover primer.

    HINT:
    1. Apply Primer G onto the ceramic notches.
    2. If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Apply adhesive to the back door glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B214800E03
    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      Standard Dimension:
      Item
      Dimension
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all the adhesive within the time described in the table below.

      Usage Time Frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour and 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the back door glass as shown in the illustration.


      B229483E01


      Text in Illustration 
      *1
      Ceramic Notch
      -
      -

      Standard Dimension:
      Item
      Dimension
      a
      4.8 mm (0.189 in.)



  1. Install the back door glass.



      B229472
    1. Using suction cups, engage the 2 clips to install the back door glass.

      NOTICE:
      1. Check that the clips are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and back door glass.

    2. Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.

      HINT:
      Press the back door glass with a force of 98 N (10 kgf, 22 lbf) or more.



    3. BO03986E06
    4. Using a scraper, remove any excess or protruding adhesive.

      HINT:
      Apply adhesive onto the glass rim.

    5. Hold the back door glass using protective tape until applied adhesive becomes hard.

      NOTICE:
      Do not drive the vehicle within the time described in the table below.

      Minimum Time:
      Temperature
      Minimum Time prior to Driving Vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



    B229469
  1. Connect the 2 connectors.



16. INSPECT FOR LEAK AND REPAIR
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.



17. INSTALL REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)
  1. for Back Door Glass:

    1. Install the rear wiper motor assembly .



18. INSTALL REAR WIPER MOTOR GROMMET (w/ Rear Wiper)
  1. for Back Door Glass:

    1. Install the rear wiper motor grommet .



19. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)
  1. for Back Door Glass:

    1. Install the rear wiper arm and blade assembly .



20. INSTALL REAR WIPER ARM HEAD CAP (w/ Rear Wiper)
  1. for Back Door Glass:

    1. Install the rear wiper arm head cap .



21. INSTALL REAR SPOILER ASSEMBLY


    B229326
  1. Engage the 2 clips to install the rear spoiler assembly.



    B228492
  1. Install the 5 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the connector.



22. INSTALL BACK DOOR TRIM BOARD


    B227903
  1. Engage the 5 clips and 2 guides to install the back door trim board.



23. INSTALL BACK DOOR TRIM BOARD ASSEMBLY


    B227902
  1. Engage the 11 clips and 2 claws to install the back door panel trim assembly.



24. INSTALL BACK DOOR SIDE GARNISH LH


    B227898
  1. Engage the 3 clips and 2 claws to install the back door side garnish LH.



25. INSTALL BACK DOOR SIDE GARNISH RH


    B227897
  1. Engage the 3 clips and 2 claws to install the back door side garnish RH.



26. INSTALL UPPER BACK DOOR TRIM PANEL ASSEMBLY


    B227896
  1. Engage the 4 clips and 4 claws to install the upper back door trim panel assembly.