Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS

BACK DOOR GLASS > REMOVAL

for Preparation Click here



1. REMOVE UPPER BACK DOOR TRIM PANEL ASSEMBLY


    B227895
  1. Using a moulding remover, disengage the 4 clips and 4 claws, and remove the upper back door trim panel assembly.



2. REMOVE BACK DOOR SIDE GARNISH RH


    B227897
  1. Disengage the 3 clips and 2 claws, and remove the back door side garnish RH.



3. REMOVE BACK DOOR SIDE GARNISH LH


    B227898
  1. Disengage the 3 clips and 2 claws, and remove the back door side garnish LH.



4. REMOVE BACK DOOR TRIM BOARD ASSEMBLY


    B227899
  1. Using a moulding remover, disengage the clip and claw.



    B227900
  1. Using a moulding remover, disengage the clip and claw.



    B257325E01
  1. Disengage the 3 clips in the order shown in the illustration.



    B257326
  1. Disengage the 2 clips by pulling the back door trim board assembly in the direction indicated by the arrows in the illustration.



    B257327E01
  1. Remove the back door trim board assembly by pulling it in the direction indicated by the arrow in the illustration to disengage the 4 clips.
    Text in Illustration 
    *1
    Back Door Trim Board Assembly
    *2
    Back Door Panel
    *a
    The portion that may be damaged due to interference

    NOTICE:
    Make sure to pull the back door trim board assembly in the direction indicated by the arrow in the illustration. If the back door trim board assembly is removed from the lower part, the door pull handle mounting area may interfere with the back door panel, resulting in damage to the back door trim board assembly.



5. REMOVE BACK DOOR TRIM BOARD


    B227903
  1. Disengage the 5 clips and 2 guides, and remove the back door trim board.



6. REMOVE REAR SPOILER ASSEMBLY


    B228492
  1. Disconnect the connector.

  1. Remove the 5 nuts.



    B228493
  1. Disengage the 2 clips to remove the rear spoiler assembly.



7. REMOVE REAR WIPER ARM HEAD CAP (w/ Rear Wiper)
  1. for Back Door Glass:

    1. Remove the rear wiper arm head cap .



8. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)
  1. for Back Door Glass:

    1. Remove the rear wiper arm and blade assembly .



9. REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)
  1. for Back Door Glass:

    1. Remove the rear wiper motor grommet .



10. REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)
  1. for Back Door Glass:

    1. Remove the rear wiper motor assembly .



11. REMOVE BACK DOOR GLASS


    B229469
  1. Disconnect the 2 connectors.



    B229494E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    When separating the back door glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.



    B275806E01
  1. Pass a piano wire between the vehicle body and back door glass from the interior, as shown in the illustration.

    HINT:
    Do not allow the piano wire to interfere with the clips.

    Text in Illustration 
    *1
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

  1. Cut off the adhesive by pulling the piano wire around the back door glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the back door glass.



    B229472
  1. Using suction cups, disengage the 2 clips and remove the back door glass.



12. REMOVE NO. 1 BACK DOOR GLASS ADHESIVE DAM


    B229473
  1. Remove the No. 1 back door glass adhesive dam.



13. REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING LH


    B229474E01
  1. Remove the No. 1 back window outside moulding LH.
    Text in Illustration 
    *1
    LH Side
    *2
    RH Side



14. REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING RH

HINT:
Use the same procedure for the RH side and LH side.



15. REMOVE NO. 1 BACK WINDOW LOWER MOULDING


    B229475
  1. Remove the No. 1 back window lower moulding.



16. REMOVE NO. 2 BACK WINDOW GLASS SPACER


    B229476E01
  1. Using a scraper, remove the No. 2 back window glass spacer.
    Text in Illustration 
    *1
    No. 2 Back Window Glass Spacer
    *2
    No. 1 Back Window Glass Spacer

    NOTICE:
    1. Be careful not to damage the back door glass.
    2. Be sure to replace the No. 1 back window glass spacer with a new one.



17. REMOVE NO. 1 BACK WINDOW GLASS SPACER

HINT:
Use the same procedure for the No. 1 spacer and No. 2 spacer.



18. CLEAN BACK DOOR GLASS


    BO04421E02
  1. Clean the outer edge of the back door glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the back door glass surface after cleaning it.
    2. Be careful not to damage the glass.
    3. Even if using a new back door glass, clean the back door glass with a non-residue solvent.



19. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
  1. for Back Door Window Fix Glass:

    1. Remove the back door outside garnish sub-assembly .



20. REMOVE BACK WINDOW FIX GLASS


    B229454
  1. Disconnect the 2 connectors.



    B229455E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    When separating the back door glass vehicle, be careful not to damage the interior and exterior ornaments.



    B275805E01
  1. Pass a piano wire between the vehicle body and back window fix glass from the interior, as shown in the illustration.
    Text in Illustration 
    *1
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

  1. Cut off the adhesive by pulling the piano wire around the back door glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the back door glass.



    B229457
  1. Using suction cups, disengage the 2 clips and remove the back door glass.



21. REMOVE NO. 2 BACK DOOR GLASS ADHESIVE DAM


    B229458
  1. Using a scraper, remove the back door glass adhesive dam.

    NOTICE:
    1. Be careful not to damage the back window fix glass.
    2. Be sure to replace the back door glass adhesive dam with a new one.



22. REMOVE NO. 2 BACK WINDOW OUTSIDE MOULDING LH


    B229459E01
  1. Using a scraper, remove the NO. 2 back window outside moulding LH.
    Text in Illustration 
    *1
    LH Side
    *2
    RH Side

    NOTICE:
    1. Be careful not to damage the back window fix glass.
    2. Be sure to replace the back window outside moulding with a new one.



23. REMOVE NO. 2 BACK WINDOW OUTSIDE MOULDING RH

HINT:
Use the same procedure for the RH side and LH side.



24. REMOVE NO. 2 BACK WINDOW LOWER MOULDING


    B229460
  1. Using a scraper, remove the back window lower moulding.

    NOTICE:
    1. Be careful not to damage the back window fix glass.
    2. Be sure to replace the back window lower moulding with a new one.



25. REMOVE NO. 2 BACK DOOR GLASS SPACER


    B229461E01
  1. Using a scraper, remove the No. 2 back door glass spacer.
    Text in Illustration 
    *1
    No. 2 Back Window Glass Spacer
    *2
    No. 1 Back Window Glass Spacer

    NOTICE:
    1. Be careful not to damage the back window fix glass.
    2. Be sure to replace the No. 2 back window glass spacer with a new one.



26. REMOVE NO. 1 BACK DOOR GLASS SPACER

HINT:
Use the same procedure for the No. 1 spacer and No. 2 spacer.



27. CLEAN BACK WINDOW FIX GLASS


    BO04421E02
  1. Clean the outer edge of the back window fix glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the back window fix glass surface after cleaning it.
    2. Be careful not to damage the glass.
    3. Even if using a new back window fix glass, clean the back window fix glass with a non-residue solvent.



28. CLEAN VEHICLE BODY


    B149737E07
  1. Using a scraper, remove the moulding and adhesive from the back window fix glass.
    Text in Illustration 
    *1
    Adhesive
    *2
    Vehicle Body

  1. Clean and shape the contact surfaces of the vehicle body.

    1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.