Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > High Beam Headlight Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the high beam headlights.

WIRING DIAGRAM


for Canada

E191081E14


except Canada

E191094E13


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK OPERATION (LOW BEAM HEADLIGHTS)
  1. Check the operation of the low beam headlights.

    OK:
    Low beam headlights operate normally.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check that the high beam headlights illuminate.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light Hi
    High beam headlights
    ON/OFF
    -

    OK:
    High beam headlights illuminate.



NG
Go to step 3
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.CHECK MODEL
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    for Canada
    A
    except Canada
    B



B
Go to step 7
A


4.INSPECT RUNNING LIGHT RELAY


    E191082E02
  1. Connect a positive (+) lead from the battery to terminal 6 (+B).

  1. Connect a negative (-) lead from the battery to terminals 4 (H) and 3 (E).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 (HLOR) - Battery negative
    Always
    11 to 14 V
    5 (HLOL) - Battery negative
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Component without harness connected
    (Running Light Relay)



NG
REPLACE RUNNING LIGHT RELAY
OK


5.CHECK HARNESS AND CONNECTOR (RUNNING LIGHT RELAY - INSTRUMENT PANEL JUNCTION BLOCK AND BODY GROUND)
  1. Disconnect the 2C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 4 (H) - 2C-22
    Always
    Below 1 Ω
    2C-22 - Body ground
    Always
    10 kΩ or higher
    Relay terminal 3 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    E182506E09
  1. Remove the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-22 - A-22 (DIM)
    Always
    Below 1 Ω
    2C-22 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

7.INSPECT HEADLIGHT DIMMER RELAY (DIM)


    E108359E01
  1. Remove the headlight dimmer relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE HEADLIGHT DIMMER RELAY
OK


8.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT DIMMER RELAY)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 2 - Body ground
    Always
    11 to 14 V
    Relay terminal 3 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY - INSTRUMENT PANEL JUNCTION BLOCK)
  1. Disconnect the 2C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 1 - 2C-22
    Always
    Below 1 Ω
    2C-22 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    E182506E09
  1. Remove the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-22 - A-22 (DIM)
    Always
    Below 1 Ω
    2C-22 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)