REAR BRAKE > INSTALLATION |
| 1. INSTALL REAR DISC |
![]() |
Align the matchmarks of the disc and axle hub, and install the disc.
| *1 | Matchmark |
| 2. INSTALL REAR DISC BRAKE CYLINDER MOUNTING |
![]() |
Install the rear disc brake cylinder mounting to the axle beam with the 2 bolts.
| 3. INSTALL REAR DISC BRAKE BUSHING DUST BOOT |
![]() |
Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.
![]() |
Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.
| 4. INSTALL REAR DISC BRAKE PAD GUIDE PIN |
![]() |
Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the 2 rear disc brake pad guide pins.
![]() |
Install the 2 rear disc brake pad guide pins to the rear disc brake cylinder mounting.
| 5. INSTALL REAR DISC BRAKE PAD SUPPORT PLATE |
![]() |
Install the 2 rear disc brake pad support plates to the rear disc brake cylinder mounting.
| 6. INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM |
![]() |
Apply disc brake grease to the back plate of the rear disc brake pads.
![]() | Disc Brake Grease |
![]() |
Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim to each rear disc brake pad.
| *1 | Rear No. 1 Disc Brake Anti-squeal Shim |
| *2 | Rear No. 2 Disc Brake Anti-squeal Shim |
| 7. INSTALL REAR DISC BRAKE PAD |
![]() |
Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.
![]() |
Install the 2 anti-squeal springs to the rear disc brake pads.
| 8. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY |
![]() |
To compensate for pad lining thickness, use SST to adjust the protrusion of the rear disc brake piston by turning it.
![]() |
Hold the rear disc brake cylinder pad guide pin, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.
| *1 | Hold |
| *2 | Turn |
| 9. CONNECT REAR FLEXIBLE HOSE |
![]() |
Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.
| 10. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.
| *1 | No. 3 Parking Brake Cable Assembly |
| *2 | Clip |
![]() |
Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.
| 11. FILL RESERVOIR WITH BRAKE FLUID |
| 12. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL |
Connect the cable to the negative (-) auxiliary battery terminal.
Perform the following procedure if air bleeding is not necessary:
Connect the reservoir level switch connector.
Clear the DTCs (Click here).
| 13. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 14. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 15. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type) |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 16. BLEED BRAKE LINE |
Remove the center cowl top ventilator cover.
![]() |
Slide the hood to cowl top seal and disengage the claw.
Disengage the 2 claws and 3 guides, and remove the center cowl top ventilator cover.
Bleed brake line.
![]() |
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid into the reservoir between MAX and MIN level on the brake fluid reservoir.
Connect the Techstream to the DLC3 and turn the power switch on (IG).
Turn the Techstream on and enter the following menus: Chassis / ABS/VSC/TRAC / Air Bleeding.
Select the "Usual air bleeding" on the Techstream display, and bleed air from the brake fluid following the instructions on the Techstream.
After air bleeding, tighten each bleeder plug.
Clear the DTCs (Click here).
Turn the Techstream off and turn the power switch off.
Inspect for brake fluid leaks.
Install the brake master cylinder reservoir filler cap.
Install the center cowl top ventilator cover.
![]() |
Engage the 2 claws and 3 guides to install the center cowl top ventilator cover.
Slide the hood to cowl top seal to engage the claw.
| 17. ADJUST PARKING BRAKE |
| 18. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
Connect each connector.
Engage the clamp.
Engage the 2 guides and claw to connect the hood lock control cable.
![]() |
Engage the 6 claws and clip.
Install the lower instrument panel finish panel assembly with the screw <C>.
| 19. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the 2 clips.
Install the cowl side trim board LH with the clip.
| 20. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the 10 claws to install the front door scuff plate LH.
| 21. INSTALL REAR WHEEL |