Home › Engine / Hybrid System › 2ZR-FXE FUEL › FUEL INJECTOR

FUEL INJECTOR > INSPECTION

for Preparation Click here



1. INSPECT FUEL INJECTOR ASSEMBLY


    A154756
  1. Check the resistance.

    1. Using an ohmmeter, measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      20°C (68°F)
      11.6 to 12.4 Ω

      If the result is not as specified, replace the injector assembly.



  1. Check the operation.
    Inspect the injector injection volume.

    CAUTION:
    Perform the inspection in a well-ventilated area.
    Do not perform the inspection near a naked flame.




      A264971E01
    1. Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).
      Text in Illustration 
      *1
      SST
      (Hose)
      *2
      SST
      (Hose Band)
      *3
      SST
      (Fuel Tube Connector)
      *4
      Fuel Pipe (Vehicle Side)

      SST
      09268-31014   (09268-41500, 09268-41700, 95336-08070)

      NOTICE:
      Ensure that the SST connector O-rings are not damaged and are free of foreign matter as they are used to seal the connections between the fuel tube connector and pipe.

    2. Install a new O-ring onto the fuel injector assembly.



    3. A264972E01
    4. Connect SST (adapter and hose) to the injector assembly, and hold the injector assembly and union with SST (clamp).
      Text in Illustration 
      *1
      SST
      (Hose)
      *2
      SST
      (Hose Band)
      *3
      SST
      (Adapter)
      *4
      O-ring
      *5
      SST
      (Clamp)
      *6
      Vinyl Tube

      SST
      09268-31014   (09268-41110, 09268-41300, 09268-41700, 95336-08070)

      CAUTION:
      Install a suitable vinyl tube onto the injector assembly to prevent gasoline from spraying.



    5. A264974E01
    6. Tie SST (clamp and adapter) together with SST (tie band) as shown in the illustration.
      Text in Illustration 
      *1
      SST
      (Tie Band)
      *2
      SST
      (Adapter)
      *3
      SST
      (Clamp)

      SST
      09268-31014   (09268-41110, 09268-41300, 09268-41800)

    7. Set the injector assembly in a graduated cylinder.

    8. Operate the fuel pump .



    9. A264973E01
    10. Connect SST (wire) to the injector assembly and the battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.
      Text in Illustration 
      *1
      SST
      (Wire)
      *a
      Connect

      SST
      09842-30080  

      NOTICE:
      Always switch the voltage on and off at the battery side, not the injector side.

      Standard Injection Volume:
      Tester Connection
      Condition
      Specified Condition
      Positive terminal - Ground terminal
      Per 15 seconds
      60 to 73 cc (3.7 to 4.5 cu. in.)

      Difference between each injector:
      13 cc (0.8 cu. in.) or less

      If the injection volume is not as specified, replace the injector assembly.



    A138003
  1. Inspect for leaks.

    1. In the condition above, disconnect the test probes of SST (wire) from the battery and check the fuel leaks from the injector.

      Standard fuel drop:
      1 drop or less every 25 minutes

      If the injection volume is not as specified, replace the injector assembly.