Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING

SLIDING ROOF HOUSING > REMOVAL

for Preparation Click here


CAUTION:
OPERATION PRECAUTIONS (Click here)



1. REMOVE SLIDING ROOF SIDE GARNISH LH


    B230202
  1. Remove the sliding roof side garnish LH.



2. REMOVE SLIDING ROOF SIDE GARNISH RH

HINT:
Use the same procedure for the RH side and LH side.



3. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY


    B229306
  1. Using a T25 "TORX" driver, remove the 6 screws.

  1. Remove the sliding roof glass sub-assembly.



4. REMOVE TILT ROOF GLASS SUB-ASSEMBLY


    B230692
  1. Using a T20 "TORX" driver, remove the 6 screws and tilt roof glass sub-assembly.



5. REMOVE ROOF HEADLINING ASSEMBLY

HINT:
Refer to the procedure up to Remove Roof Headlining Assembly (Click here).



6. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

CAUTION:
When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.

  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



    B228036E01
  1. Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock and disconnect the curtain shield airbag connector.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



  1. Remove the 5 bolts.


    B228038



  1. Remove the 4 clips.


    B228039




      C141263E05
    1. Using a clip remover, remove the 4 pins.
      Text in Illustration 
      *1
      Pin
      *2
      Clip
      *3
      Airbag
      *4
      Body



    2. C141264E09
    3. Using a screwdriver with the tip wrapped with protective tape, separate the 4 clips and curtain shield airbag assembly from the body as shown in the illustration.
      Text in Illustration 
      *1
      Clip
      *2
      Airbag
      *3
      Body
      *4
      Spacer



  1. Disengage the 5 hooks to remove the curtain shield airbag assembly.


    B228040

  1. Remove the 4 clips and 4 spacers from the curtain shield airbag assembly.



7. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



8. REMOVE REAR SIDE RAIL SPACER LH


    B230208
  1. Disengage the 2 clamps and remove the rear side rail spacer LH.



9. REMOVE REAR SIDE RAIL SPACER RH

HINT:
Use the same procedure for the RH side and LH side.



10. REMOVE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY


    B229310
  1. Disconnect the connector.

  1. Remove the 2 bolts and sliding roof drive gear sub-assembly.



11. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH


    B229311
  1. Remove the 2 bolts, 2 nuts and front sliding roof housing mounting bracket LH.



12. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:
Use the same procedure for the RH side and LH side.



13. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET LH


    B229313
  1. Remove the 2 bolts, 2 nuts and center sliding roof housing mounting bracket LH.



14. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:
Use the same procedure for the RH side and LH side.



15. REMOVE SLIDING ROOF RAIL SUB-ASSEMBLY


    B289707
  1. Disconnect the connector.

  1. Disengage the clamp.



  1. Remove the 12 nuts and sliding roof rail sub-assembly.


    B229317



16. REMOVE MOON ROOF GLASS ASSEMBLY


    B230187E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.
    Text in Illustration 
    *1
    Protective Tape



    B230195E01
  1. Place matchmarks on the moon roof glass assembly and vehicle body on the locations indicated in the illustration.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Matchmarks are not necessary if the moon roof glass assembly is not going to be reused.



    B230188E01
  1. Pass a piano wire between the rear slide roof panel sub-assembly and moon roof glass assembly from the interior, as shown in the illustration.
    Text in Illustration 
    *1
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

  1. Cut off the adhesive by pulling the piano wire around the moon roof glass assembly.



    B230186
  1. Using suction cups, disengage the 2 clips and remove the moon roof glass assembly.



17. CLEAN MOON ROOF GLASS ASSEMBLY


    BO04421E02
  1. Clean the outer edge of the moon roof glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the moon roof glass surface after cleaning it.
    2. Be careful not to damage the glass.
    3. Even if using a new moon roof glass, clean the moon roof glass with a non-residue solvent.



18. CLEAN REAR SLIDE ROOF PANEL SUB-ASSEMBLY


    B231657E01
  1. Using a scraper, remove the moulding and adhesive from the moon roof glass.
    Text in Illustration 
    *1
    Adhesive
    *2
    Rear Slide Roof Panel Sub-assembly

  1. Clean and shape the contact surfaces of the rear slide roof panel sub-assembly.

    1. Using a knife, cut away excess adhesive on the contact surfaces of the rear slide roof panel sub-assembly, as shown in the illustration.

      NOTICE:
      Be careful not to damage the rear slide roof panel sub-assembly.

    2. Clean the contact surfaces of the rear slide roof panel sub-assembly with a piece of cloth saturated with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the rear slide roof panel sub-assembly.



19. REMOVE REAR SLIDE ROOF PANEL SUB-ASSEMBLY


  1. Remove the 16 nuts and rear slide roof panel sub-assembly.


    B229318

    NOTICE:
    1. When removing the roof panel, be careful not to damage the vehicle.
    2. Perform this step with 2 or more technicians.