Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1656/38    Seat Belt Buckle Switch LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The side seat belt buckle switch LH circuit consists of the center airbag sensor assembly and front seat inner belt assembly LH.
DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1656/38
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit.
  2. Front seat inner belt assembly LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat inner belt assembly LH (Seat belt buckle switch LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C171040E14


INSPECTION PROCEDURE

1.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and front seat inner belt assembly LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and front seat inner belt assembly LH.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


2.CHECK FLOOR WIRE (OPEN)


  1. Using SST, connect terminals 11 (LBE+) and 12 (LBE-) of connector B.


    C171045E12

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R4-2 (LBE+) - R4-1 (LBE-)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *5
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)
    *6
    Connector B
    *7
    Connector C
    -
    -



NG
REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (SHORT)


    C171046E09
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R4-2 (LBE+) - R4-1 (LBE-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)
    *5
    Connector C



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (SHORT TO B+)


    C171046E09
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R4-2 (LBE+) - Body ground
    Power switch on (IG)
    Below 1 V
    R4-1 (LBE-) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)
    *5
    Connector C



NG
REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT TO GROUND)


    C171046E09
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R4-2 (LBE+) - Body ground
    Always
    1 MΩ or higher
    R4-1 (LBE-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)
    *5
    Connector C



NG
REPLACE FLOOR WIRE
OK


6.CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    C166120E08
  1. Connect the connectors to the center airbag sensor assembly and front seat inner belt assembly LH.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656/38 is not output.

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Replace the front seat inner belt assembly LH with a known good part (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.


NEXT


8.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C166120E08
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656/38 is not output.

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END