Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSPECTION

for Preparation Click here



1. INSPECT FRONT DOOR LOCK ASSEMBLY LH


    B228534E01
  1. Check the operation of the door lock motor.

    1. Apply battery voltage and check the operation of the door lock motor.

      OK:
      Connection
      Result
      Battery positive (+) → Terminal 4 (L)
      Battery negative (-) → Terminal 1 (UL)
      Locks
      Battery positive (+) → Terminal 1 (UL)
      Battery negative (-) → Terminal 4 (L)
      Unlocks

      Text in Illustration 
      *1
      Component without harness connected
      (Front Door Lock Assembly LH)
      *2
      Unlock
      *3
      Lock
      If the result is not as specified, replace the front door lock assembly LH.



    B228534E02
  1. Check the operation of the door unlock detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      7 (E) - 8 (LSSR)
      Locked
      10 kΩ or higher
      7 (E) - 8 (LSSR)
      Unlocked
      Below 1 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Front Door Lock Assembly LH)
      *2
      Unlock
      *3
      Lock
      If the result is not as specified, replace the front door lock assembly LH.



    B228538E03
  1. Check the operation of the door key lock and unlock switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      7 (E) - 9 (L)
      Locked
      Below 1 Ω
      7 (E) - 9 (L)
      off
      10 kΩ or higher
      7 (E) - 10 (UL)
      Unlocked
      Below 1 Ω
      7 (E) - 10 (UL)
      off
      10 kΩ or higher

      Text in Illustration 
      *1
      Component without harness connected
      (Front Door Lock Assembly LH)
      *2
      Lock
      *3
      off
      *4
      Unlock
      If the result is not as specified, replace the front door lock assembly LH.



2. INSPECT FRONT DOOR LOCK ASSEMBLY RH


    B228535E01
  1. Check the operation of the door lock motor.

    1. Apply battery voltage and check the operation of the door lock motor.

      OK:
      Connection
      Result
      Battery positive (+) → Terminal 4 (L)
      Battery negative (-) → Terminal 1 (UL)
      Locks
      Battery positive (+) → Terminal 1 (UL)
      Battery negative (-) → Terminal 4 (L)
      Unlocks

      Text in Illustration 
      *1
      Component without harness connected
      (Front Door Lock Assembly RH)
      *2
      Unlock
      *3
      Lock
      If the result is not as specified, replace the front door lock assembly RH.



    B228535E02
  1. Check the operation of the door unlock detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Locked
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlocked
      Below 1 Ω

      Text in Illustration 
      *1
      Component without harness connected
      (Front Door Lock Assembly RH)
      *2
      Unlock
      *3
      Lock
      If the result is not as specified, replace the front door lock assembly RH.