ELECTRONIC SHIFT LEVER SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Chassis / Transmission Control / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift Pos Display (P) | Shift position display (P) / ON or OFF | ON: Park (P) selected OFF: A shift state other than park (P) selected (When normal) (May go off under malfunction) | - |
| Shift Pos Display (Not P) | Shift position display (not P) / ON or OFF | ON: A shift state other than park (P) selected (When normal) (May go off under malfunction) OFF: Park (P) selected | - |
| Master Caution Display | Master caution display / Disp or Nondisp | Disp: Malfunction occurs in this system Nondisp: Malfunction does not occur in this system | Transmission control ECU assembly |
| PSW Indicator Mode | PSW indicator mode / ON or OFF | ON: Park (P) selected OFF: A shift state other than park (P) selected (When normal) (May go off under malfunction) | - |
| U Phase Voltage Value | U phase voltage value / Min: 0 V, Max: 39 V | 9 to 14 V: On (IG) (If voltage is applied to the shift control actuator assembly: 0 V) | Shift control actuator assembly [parking lock motor (MUA)] signal circuit |
| V Phase Voltage Value | V phase voltage value / Min: 0 V, Max: 39 V | 9 to 14 V: On (IG) (If voltage is applied to the shift control actuator assembly: 0 V) | Shift control actuator assembly [parking lock motor(MVA)] signal circuit |
| W Phase Voltage Value | W phase voltage value / Min: 0 V, Max: 39 V | 9 to 14 V: On (IG) (If voltage is applied to the shift control actuator assembly: 0 V) | Shift control actuator assembly [parking lock motor(MWA)] signal circuit |
| Battery Voltage Value | BATT voltage value / Min: 0 V, Max: 19 V | 8 to 16 V: On (IG) | BATT signal circuit |
| IG (+B) Voltage Value | IG (+B) voltage value / Min: 0 V, Max: 19 V | 8 to 16 V: On (IG) | +B signal circuit |
| Cmplte of Learn Lck Pos | Completion of learning lock position / OK or NG | OK: On (IG) | - |
| Cmplte of Learn Unlck Pos | Completion of learning unlock position / OK or NG | OK: Power switch on (IG), Park (P) selected → Neutral (N) selected and number of trips after learning is less than 3 or power switch on (IG) and number of trips after learning is 3 or more NG: Power switch on (IG), a shift state other than Park (P) has not been selected and number of trips after learning is less than 3 |
|
| # of Trip Cuntr after Learn | Number of trips after learning / Min: 0, Max: 65535 | Actual number of trips (Power switch on (IG)) | - |
| Main Relay for Motor Drive | P CON MTR relay (transaxle parking lock control relay) for motor drive / ON or OFF | OK: On (IG) | - |
| U Phase Crnt-Carry Status | U phase current-carrying status / ON or OFF | ON: U phase current flows OFF: U phase current does not flow | Shift control actuator assembly [parking lock motor (MUA)] signal circuit |
| V Phase Crnt-Carry Status | V phase current-carrying status / ON or OFF | ON: V phase current flows OFF: V phase current does not flow | Shift control actuator assembly [parking lock motor (MVA)] signal circuit |
| W Phase Crnt-Carry Status | W phase current-carrying status / ON or OFF | ON: W phase current flows OFF: W phase current does not flow | Shift control actuator assembly [parking lock motor (MWA)] signal circuit |
| U Phase Voltage Status | U phase voltage status / ON or OFF | ON: 9 to 14 V OFF: 0 V | Shift control actuator assembly [parking lock motor (MUA)] signal circuit |
| V Phase Voltage Status | V phase voltage status / ON or OFF | ON: 9 to 14 V OFF: 0 V | Shift control actuator assembly [parking lock motor (MVA)] signal circuit |
| W Phase Voltage Status | W phase voltage status / ON or OFF | ON: 9 to 14 V OFF: 0 V | Shift control actuator assembly [parking lock motor (MWA)] signal circuit |
| Battery Voltage Status | BATT voltage status / ON or OFF | ON: 8 to 16 V OFF: Below 8 V | BATT signal circuit |
| IG (+B) Phase Vol Status | IG (+B) phase voltage status / ON or OFF | ON: 10 to 16 V OFF: Below 10 V | +B signal circuit |
| ACC Condition Signal | ACC condition signal / ON or OFF | ON: 5 V or higher OFF: Below 5 V | Judged according to the ACC signal via CAN communication line |
| Init Drv Cntrl Completed | Initial drive control completed / OK or NG | OK: On (IG) | - |
| Cmplte of Detct Lck Pos | Completion of detecting lock position / OK or NG | OK: On (IG) | - |
| Cmplte of Detct Unlck Pos | Completion of detecting unlock position / OK or NG | OK: Power switch on (IG), Park (P) selected → Neutral (N) selected and number of trips after learning is less than 3 NG: Power switch on (IG) and number of trips after learning is 3 or more | NG is displayed when P/Not P Move Shft Range is Set and number of trips is 3 or more |
| P/Not P Move Shft Range | P/Not P movable shift range / Set or Unset | Set: Power switch on (IG), Park (P) selected → Neutral (N) selected and number of trips after learning is less than 3 or power switch on (IG) and number of trips after learning is 3 or more Unset: Power switch on (IG), a shift state other than Park (P) has not been selected and number of trips after learning is less than 3 | - |
| Main Relay | P CON MTR relay (transaxle parking lock control relay) / Normal or Abnoml | Normal: On (IG) | - |
| Current flag record | Current flag record ON or OFF | ON: Current flag record stored OFF: Current flag record not stored | - |
| Number of Diagnosis Code | Number of diagnosis codes / Min: 0, Max: 255 | Actual number of DTCs | - |