Home › Drivetrain › P410 HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM

ELECTRONIC SHIFT LEVER SYSTEM > "P" Position Switch Indicator Light Circuit

for Preparation Click here


DESCRIPTION

The indicator light comes on when the P position switch (transmission shift main switch) is pressed (park (P) selected), goes off when a shift state other than park (P) is selected and goes off when a system malfunction occurs. Then an error message is displayed on the multi display.

WIRING DIAGRAM


C209919E08


INSPECTION PROCEDURE

1.CHECK TRANSMISSION SHIFT MAIN SWITCH (INDICATOR LIGHT)
  1. Turn the power switch on (IG).

  1. Depress the brake pedal and move the shift lever to select neutral (N).

  1. Inspect the indicator light condition by operating the P position switch (transmission shift main switch).

    Result:
    Condition of Indicator Light
    Proceed to
    Indicator light does not go off. (Remains on)
    A
    Indicator light does not come on.
    B

  1. Turn the power switch off.



B
Go to step 4
A


2.CHECK TRANSMISSION SHIFT MAIN SWITCH (INDICATOR LIGHT)
  1. Disconnect connector A23 from the transmission control ECU assembly.

  1. Turn the power switch on (IG).

  1. Inspect the indicator light condition by operating the P position switch (transmission shift main switch).

    Result:
    Condition of Indicator Light
    Proceed to
    Indicator light does not go off. (Remains on)
    A
    Indicator light goes off.
    B

    NOTICE:
    Turning the power switch on (IG) with the transmission control ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Connect the transmission control ECU assembly connector.



B
REPLACE TRANSMISSION CONTROL ECU ASSEMBLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU - TRANSMISSION SHIFT MAIN SWITCH)
  1. Disconnect connector A23 from the transmission control ECU assembly.

  1. Disconnect connector from the P position switch (transmission shift main switch).



    C210349E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-20 (IND) or b1-7 (IND-) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control ECU Assembly)
    *b
    Front view of wire harness connector
    (to P Position Switch (Transmission Shift Main Switch))

  1. Connect the P position switch (transmission shift main switch) connector.

  1. Connect the transmission control ECU assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION SHIFT MAIN SWITCH 

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION SHIFT MAIN SWITCH POWER SOURCE CIRCUIT)
  1. Disconnect the connector from the P position switch (transmission shift main switch).



    C208992E10
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b1-6 (IND+) - Body ground
    Power switch off
    9 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to P Position Switch (Transmission Shift Main Switch))

  1. Connect the P position switch (transmission shift main switch) connector.



NG
CHECK AND REPAIR POWER SOURCE CIRCUIT
OK


5.INSPECT TRANSMISSION SHIFT MAIN SWITCH
  1. Disconnect the connector from the P position switch (transmission shift main switch).



    A216509E11
  1. Apply auxiliary battery voltage between terminals b1-6 (IND+) and b1-7 (IND-) and check the indicator light.

    Result:
    Condition
    Specified Condition
    Auxiliary battery voltage applied between terminals b1-6 (IND+) and b1-7 (IND-)
    Comes on

    Text in Illustration 
    *a
    Component without harness connected
    (P Position Switch (Transmission Shift Main Switch))

    HINT:
    Terminals No. 1 and No. 8 on the component side connector are empty.

  1. Connect the P position switch (transmission shift main switch) connector.



NG
REPLACE TRANSMISSION SHIFT MAIN SWITCH
OK


6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU - TRANSMISSION SHIFT MAIN SWITCH)
  1. Disconnect connector A23 from the transmission control ECU assembly.

  1. Disconnect the connector from the P position switch (transmission shift main switch).



    C210349E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A23-20 (IND) - b1-7 (IND-)
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control ECU Assembly)
    *b
    Front view of wire harness connector
    (to P Position Switch (Transmission Shift Main Switch))

  1. Connect the P position switch (transmission shift main switch) connector.

  1. Connect the transmission control ECU assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY (Click here)