Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1660/43    Passenger Airbag ON/OFF Indicator Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the center airbag sensor assembly and passenger seat belt warning light assembly (passenger airbag ON/OFF indicator).
The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag and front seat outer belt RH.
DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1660/43
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit.
  2. Passenger seat belt warning light assembly malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. No. 2 Instrument panel wire
  3. No. 5 Instrument panel wire
  4. Passenger seat belt warning light assembly (Passenger airbag ON/OFF indicator)
  5. Center airbag sensor assembly

WIRING DIAGRAM


C203082E06


INSPECTION PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
  1. Turn the power switch on (IG).



  1. Check the passenger airbag ON/OFF indicator operation.

    HINT:
    Refer to the normal condition of the passenger airbag ON/OFF indicator (Click here).


    C123768E69


    Result:

    ON/OFF Indicator Illumination
    Proceed to
    Always ON
    A
    OFF
    B



B
Go to step 9
A


2.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and passenger seat belt warning light assembly. Also check that the connectors that link the instrument panel wire, No. 2 instrument panel wire and No. 5 instrument panel wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and passenger seat belt warning light assembly. Also disconnect the connectors that link the instrument panel wire, No. 2 instrument panel wire and No. 5 instrument panel wire.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR


    C210334
  1. Connect the connectors that link the instrument panel wire, No. 2 instrument panel wire and No. 5 instrument panel wire.

  1. Connect the connector to the passenger seat belt warning light assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Check the passenger airbag ON/OFF indicator operation.

    OK:
    The passenger airbag ON/OFF indicator does not come on.



NG
Go to step 5
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C210787E01
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (OPEN)


  1. Turn the power switch off.


    C210629E03

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Connect the connectors that link the instrument panel wire, No. 2 instrument panel wire and No. 5 instrument panel wire.

  1. Disconnect the connector from the passenger seat belt warning light assembly.

  1. Using SST, connect terminals 23 (PAON) and 17 (P-A/B) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 (PAON) - M2-5 (P-AB)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *4
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)
    *5
    Connector B
    *6
    Connector G



NG
Go to step 17
OK


6.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT)


    C210630E01
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 (PAON) - M2-5 (P-AB)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)
    *4
    Connector G



NG
Go to step 19
OK


7.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO GROUND)


    C210630E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 (PAON) - Body ground
    Always
    1 MΩ or higher
    M2-5 (P-AB) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)
    *4
    Connector G



NG
Go to step 21
OK


8.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO B+)


    C210630E01
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M2-1 (PAON) - Body ground
    Power switch on (IG)
    Below 1 V
    M2-5 (P-AB) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)
    *4
    Connector G



NG
Go to step 23
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

9.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and passenger seat belt warning light assembly. Also check that the connectors that link the instrument panel wire, No. 2 instrument panel wire and No. 5 instrument panel wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and passenger seat belt warning light assembly. Also disconnect the connectors that link the instrument panel wire, No. 2 instrument panel wire and No. 5 instrument panel wire.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (OPEN)


  1. Connect the connectors that link the instrument panel wire, No. 2 instrument panel wire and No. 5 instrument panel wire.


    C210629E03

  1. Using SST, connect terminals 23 (PAON) and 17 (P-A/B) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 (PAON) - M2-5 (P-AB)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *4
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)
    *5
    Connector B
    *6
    Connector G



NG
Go to step 17
OK


11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT)


    C210630E01
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 (PAON) - M2-5 (P-AB)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)
    *4
    Connector G



NG
Go to step 19
OK


12.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO GROUND)


    C210630E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 (PAON) - Body ground
    Always
    1 MΩ or higher
    M2-5 (P-AB) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)
    *4
    Connector G



NG
Go to step 21
OK


13.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO B+)


    C210630E01
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M2-1 (PAON) - Body ground
    Power switch on (IG)
    Below 1 V
    M2-5 (P-AB) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)
    *4
    Connector G



NG
Go to step 23
OK


14.CHECK PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY (SOURCE VOLTAGE)


    C210795E01
  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M2-6 (IG+) - Body ground
    Power switch on (IG)
    10 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)



NG
REPLACE WIRE HARNESS OR AUXILIARY BATTERY
OK


15.CHECK PASSENGER AIRBAG ON/OFF INDICATOR


    C169197E07
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Connect the connector to the passenger seat belt warning light assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Check the indicator according to the conditions in the table below.

    Result:
    Tester Connection
    Switch Condition
    Specified Condition
    L16-23 (PAON) - Body ground
    Power switch on (IG)
    "ON" comes on
    L16-17 (P-A/B) - Body ground
    Power switch on (IG)
    "OFF" comes on

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPLACE PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY (Click here)
OK


16.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C210787E01
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

17.CHECK INSTRUMENT PANEL WIRE (OPEN)


  1. Disconnect the instrument panel wire from the No. 2 instrument panel wire.


    C210631E03

    HINT:
    SST has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    LI2-2 (PAON) - LI2-14 (P-AB)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *4
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *5
    Front view of wire harness connector
    (to No. 2 Instrument Panel Wire)
    *6
    Connector B
    *7
    Connector C
    -
    -



NG
REPLACE INSTRUMENT PANEL WIRE
OK


18.CHECK NO. 2 INSTRUMENT PANEL WIRE (OPEN)


  1. Disconnect the No. 2 instrument panel wire from the No. 5 instrument panel wire.


    C210788E01

  1. Using SST, connect terminals 2 (PAON) and 14 (P-AB) of connector D.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IM1-8 (PAON) - IM1-7 (P-AB)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    No. 5 Instrument Panel Wire
    *4
    No. 2 Instrument Panel Wire
    *5
    Instrument Panel Wire
    *6
    Front view of wire harness connector
    (to Instrument Panel Wire)
    *7
    Front view of wire harness connector
    (to No. 5 Instrument Panel Wire)
    *8
    Connector D
    *9
    Connector E
    -
    -



NG
REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK

REPLACE NO. 5 INSTRUMENT PANEL WIRE 

19.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C210632E01
  1. Disconnect the instrument panel wire from the No. 2 instrument panel wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    LI2-2 (PAON) - LI2-14 (P-AB)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *4
    Front view of wire harness connector
    (to No. 2 Instrument Panel Wire)
    *5
    Connector C



NG
REPLACE INSTRUMENT PANEL WIRE
OK


20.CHECK NO. 2 INSTRUMENT PANEL WIRE (SHORT)


    C210789E01
  1. Disconnect the No. 2 instrument panel wire from the No. 5 instrument panel wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IM1-8 (PAON) - IM1-7 (P-AB)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    No. 5 Instrument Panel Wire
    *4
    No. 2 Instrument Panel Wire
    *5
    Instrument Panel Wire
    *6
    Front view of wire harness connector
    (to No. 5 Instrument Panel Wire)
    *7
    Connector E



NG
REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK

REPLACE NO. 5 INSTRUMENT PANEL WIRE 

21.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C210632E01
  1. Disconnect the instrument panel wire from the No. 2 instrument panel wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    LI2-2 (PAON) - Body ground
    Always
    1 MΩ or higher
    LI2-14 (P-AB) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *4
    Front view of wire harness connector
    (to No. 2 Instrument Panel Wire)
    *5
    Connector C



NG
REPLACE INSTRUMENT PANEL WIRE
OK


22.CHECK NO. 2 INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C210789E01
  1. Disconnect the No. 2 instrument panel wire from the No. 5 instrument panel wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IM1-8 (PAON) - Body ground
    Always
    1 MΩ or higher
    IM1-7 (P-AB) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    No. 5 Instrument Panel Wire
    *4
    No. 2 Instrument Panel Wire
    *5
    Instrument Panel Wire
    *6
    Front view of wire harness connector
    (to No. 5 Instrument Panel Wire)
    *7
    Connector E



NG
REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK

REPLACE NO. 5 INSTRUMENT PANEL WIRE 

23.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C210632E01
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Disconnect the instrument panel wire from the No. 2 instrument panel wire.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    LI2-2 (PAON) - Body ground
    Power switch on (IG)
    Below 1 V
    LI2-14 (P-AB) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *4
    Front view of wire harness connector
    (to No. 2 Instrument Panel Wire)
    *5
    Connector C



NG
REPLACE INSTRUMENT PANEL WIRE
OK


24.CHECK NO. 2 INSTRUMENT PANEL WIRE (SHORT TO B+)


    C210789E01
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Disconnect the No. 2 instrument panel wire from the No. 5 instrument panel wire.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    IM1-8 (PAON) - Body ground
    Power switch on (IG)
    Below 1 V
    IM1-7 (P-AB) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Passenger Seat Belt Warning Light Assembly
    *2
    Center Airbag Sensor Assembly
    *3
    No. 5 Instrument Panel Wire
    *4
    No. 2 Instrument Panel Wire
    *5
    Instrument Panel Wire
    *6
    Front view of wire harness connector
    (to No. 5 Instrument Panel Wire)
    *7
    Connector E



NG
REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK

REPLACE NO. 5 INSTRUMENT PANEL WIRE