Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB

REAR AXLE HUB > REMOVAL

for Preparation Click here


NOTICE:
When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



4. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C205666
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the auxiliary battery negative (-) terminal.

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



5. REMOVE REAR WHEEL


6. REMOVE FRONT DOOR SCUFF PLATE LH


    B227761
  1. Disengage the 10 claws and remove the front door scuff plate LH.



7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B227764
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    B298862
  1. Remove the screw <C>.



    B298863
  1. Disengage the 6 claws and clip as shown in the illustration.



    B223463
  1. Disengage the claw and 2 guides and disconnect the hood lock control cable.

  1. Disconnect each connector and clamp, and remove the lower instrument panel finish panel assembly.



9. LOOSEN PARKING BRAKE CABLE
  1. Completely release the parking brake pedal.



    C206641E01
  1. Loosen the lock nut and adjusting nut to completely release the parking brake cable.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Adjusting Nut



10. DISCONNECT REAR SPEED SENSOR WIRE


    C208053
  1. Using a screwdriver, disconnect the connector from the rear speed sensor.

    NOTICE:
    Be careful not to damage the rear speed sensor.



11. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C155545E01
  1. Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.



    C155546E03
  1. Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.
    Text in Illustration 
    *1
    No. 3 Parking Brake Cable Assembly
    *2
    Clip
    *3
    Offset Wrench (14 mm)

    HINT:
    Insert an offset wrench (14 mm) at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip. Pull out the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.



12. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    C207078
  1. Remove the 2 bolts, and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.



13. REMOVE REAR DISC


    C151123E03
  1. Remove the rear disc.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Place matchmarks on the disc and axle hub.



14. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY


    C207079
  1. Remove the 4 bolts, rear axle hub and bearing assembly and rear disc brake dust cover from the rear axle beam assembly.