Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P043E    Evaporative Emission System Reference Orifice Clog Up

DTC    P043F    Evaporative Emission System Reference Orifice High Flow

DTC    P2401    Evaporative Emission System Leak Detection Pump Control Circuit Low

DTC    P2402    Evaporative Emission System Leak Detection Pump Control Circuit High

DTC    P2419    Evaporative Emission System Switching Valve Control Circuit Low

for Preparation Click here


DTC SUMMARY


DTC No.
Monitoring Item
Malfunction Detection Condition
Trouble Area
Detection Timing
Detection Logic
P043E
Reference orifice clogged
P043E, P043F, P2401, P2402 and P2419 stored when one of following conditions met during key-off EVAP monitor:
  1. Reference orifice clogged
  2. Reference orifice high-flow
  3. Leak detection pump off malfunction
  4. Leak detection pump on malfunction
  5. Vent valve on (closed) malfunction
  1. Canister pump module
  2. Connector/wire harness (Canister pump module - ECM)
  3. ECM
While power switch off
2 trip
P043F
Reference orifice high-flow
P2401
Leak detection pump stuck off
P2402
Leak detection pump stuck on
P2419
Vent valve stuck closed

HINT:
The reference orifice is located inside the canister pump module.


DESCRIPTION

The description can be found in the EVAP (Evaporative Emission) System .

MONITOR DESCRIPTION

5 hours* after the power switch is turned off, the leak detection pump creates negative pressure (vacuum) in the EVAP system. The ECM monitors for leaks and actuator malfunctions based on the EVAP pressure.

HINT:
*: If the engine coolant temperature is not less than 35°C (95°F) 5 hours after the power switch is turned off, the monitor check starts 2 hours later. If it is still not less than 35°C (95°F) 7 hours after the power switch is turned off, the monitor check starts 2.5 hours later.


Sequence
Operation
Description
Duration
-
ECM activation
Activated by soak timer, 5, 7 or 9.5 hours after power switch turned off.
-
A
Atmospheric pressure measurement
Vent valve is turned off (vent) and EVAP system pressure is measured by ECM in order to register atmospheric pressure.
If pressure in EVAP system is not between 70 kPa(abs) and 111 kPa(abs) [525 mmHg(abs) and 833 mmHg(abs)], ECM cancels EVAP system monitor.
60 seconds
B
First reference pressure measurement
In order to determine reference pressure, leak detection pump creates negative pressure (vacuum) through reference orifice and then ECM checks if leak detection pump and vent valve operate normally.
360 seconds
C
EVAP system pressure measurement
Vent valve is turned on (closed) to shut EVAP system.
Negative pressure (vacuum) is created in EVAP system, and EVAP system pressure is then measured.
Write down measured value as it will be used in leak check
If EVAP pressure does not stabilize within 15 minutes, ECM cancels EVAP system monitor.
15 minutes*
D
Purge VSV monitor
Purge VSV is opened and then EVAP system pressure is measured by ECM.
Large increase indicates normal.
10 seconds
E
Second reference pressure measurement
After second reference pressure measurement, leak check is performed by comparing first and second reference pressure measurements.
If stabilized system pressure is higher than second reference pressure, ECM determines that EVAP system is leaking.
60 seconds
-
Final check
Atmospheric pressure is measured and then monitoring result is recorded by ECM.
-
*: If only a small amount of fuel is in the fuel tank, it takes longer for the EVAP pressure to stabilize.

A264552E01


Text in Illustration 
*1
Purge VSV: Off (Closed)
*2
Purge VSV: On (Open)
*3
Vent Valve: Off (Vent)
*4
Vent Valve: On (Closed)
*5
Leak Detection Pump: Off
*6
Leak Detection Pump: On
*7
Reference Orifice (0.02 inch)
*8
Canister Pressure Sensor
*9
Canister
*10
No. 1 Canister
*11
No. 2 Canister
*12
Canister Pump Module
*13
Canister Air Filter
*14
Fuel Tank
*a
Operation A:
Atmospheric Pressure Measurement
*b
Operation B, E:
Reference Pressure Measurement
*c
Operation C:
EVAP System Pressure Measurement
*d
Operation D:
Purge VSV Monitor
*e
Atmospheric Pressure
*f
Negative Pressure
The leak detection pump creates negative pressure through the reference orifice (in operation B and E). When the system is normal, the EVAP pressure is between 97 to 100 kPa(abs) [728 to 750 mmHg(abs)]* and saturated within a minute. If not, the ECM interprets this as a malfunction. The ECM illuminates the MIL and stores a DTC if this malfunction is detected in consecutive drive cycles.
*: Typical value.

A137887E58


MONITOR STRATEGY


Required Sensors/Components
Canister pump module
Frequency of Operation
Once per driving cycle
Duration
Within 7 minutes
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Atmospheric pressure
70 kPa(abs) [525 mmHg(abs)] or more, and less than 111 kPa(abs) [833 mmHg(abs)]
Auxiliary battery voltage
10.5 V or more
Vehicle speed
Below 2.5 mph (4 km/h)
Power switch
Off
Time after key off
5, 7 or 9.5 hours
Canister pressure sensor malfunction (P0452 and P0453)
Not detected
Purge VSV
Not operated by scan tool
Vent valve
Not operated by scan tool
Leak detection pump
Not operated by scan tool
Both of the following conditions are met before key off:
Conditions 1 and 2
1. Duration that vehicle has been driven
5 minutes or more
2. EVAP purge operation
Performed
Engine coolant temperature
4.4°C (40°F) or more, and less than 35°C (95°F)
Intake air temperature
4.4°C (40°F) or more, and less than 35°C (95°F)

TYPICAL MALFUNCTION THRESHOLDS

"Saturated" indicates that the EVAP pressure change is less than 0.286 kPa(gauge) [2.14 mmHg(gauge)] in 60 seconds.

One of following conditions met
-
EVAP pressure just after reference pressure measurement started
Higher than -0.25 kPa(gauge) [-1.875 mmHg(gauge)]
Reference pressure
Less than -4.85 kPa(gauge) [-36.375 mmHg(gauge)]
Reference pressure
-1.057 kPa(gauge) [-7.9275 mmHg(gauge)] or higher
Reference pressure
Not saturated within 360 seconds
Difference between first reference pressure and second reference pressure
0.9 kPa(gauge) [6.75 mmHg(gauge)] or higher

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.
  2. Do not perform the Evaporative System Check when the fuel tank is higher than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
  3. Do not run the engine during this operation.
  4. When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
  7. After the "Evaporative System Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  8. Input the DTC: P043E, P043F, P2401, P2402 or P2419.
  9. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  10. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

Refer to the EVAP System .