Home › Engine / Hybrid System › 2ZR-FXE FUEL › FUEL PUMP

FUEL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE


    A216414
  1. Install a new fuel suction tube set gasket onto the fuel tank.



    A216422E01
  1. Install the fuel suction tube assembly with pump and gauge to the fuel tank.
    Text in Illustration 
    *1
    Protrusion
    *2
    Notch

    NOTICE:
    Make sure that the fuel sender gauge arm does not bend.

  1. Align the protrusions of the fuel suction tube assembly with pump and gauge with the notches of the fuel tank.

    NOTICE:
    Ensure that the fuel suction tube gasket is in the correct position.



2. INSTALL FUEL PUMP GAUGE RETAINER


    A216423E01
  1. While holding the fuel suction tube assembly with pump and gauge by hand, position the fuel pump gauge retainer and tighten it lightly by hand.
    Text in Illustration 
    *1
    Lock Point
    *2
    Mark
    *3
    Front of Vehicle

    NOTICE:
    Check that the contact surface of the fuel tank retainer is not scratched or damaged, and prevent the entry of foreign matter.



    A245567E01
  1. Temporarily install the SST plate and claws to the fuel pump gauge retainer.
    Text in Illustration 
    *1
    SST
    (Plate)
    *2
    SST
    (Claw)

    SST
    09808-14030   (09808-01030, 09808-01040, 09808-01050)

    HINT:
    1. Hold the fuel suction tube assembly upright by hand to ensure that the fuel suction tube gasket is not moved out of position.
    2. Engage the SST claws securely with the fuel pump gauge retainer holes to secure SST.
    3. Make sure that only 2 claws are used with SST.

  1. While pressing the claws of SST to the fuel pump gauge retainer ribs securely, tighten the bolts.

    HINT:
    Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).

  1. Install the SST handle.



    A245569E01
  1. Using SST, align the marks on the fuel tank and fuel pump gauge retainer.
    Text in Illustration 
    *1
    SST
    (Handle)
    *2
    SST
    (Plate)
    *3
    SST
    (Claw)
    *4
    Lock Point
    *5
    Starting Point
    *a
    Front of Vehicle

    SST
    09808-14030   (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)

    NOTICE:
    1. Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
    2. Tighten the retainer by turning it clockwise while holding SST down.
    3. Make sure to rotate the SST handle horizontally. If the SST handle is rotated at an angle, SST may come off.
    4. Do not spin SST too fast or use an impact wrench as this may result in damage to components.
    5. If SST comes off of the retainer, loosen the SST bolts and reinstall SST.



3. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A216425E01
  1. Push the fuel tube joint in the plug of the fuel suction plate, then install the tube joint clip.
    Text in Illustration 
    *1
    Tube Joint Clip
    *2
    Fuel Tank Main Tube clamp
    *3
    Fuel Tube Joint
    *4
    O-ring
    *5
    Collar

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected part of the fuel tube joint and plug before performing this work.
    2. Check that the fuel tube joint is securely inserted to the end.
    3. Check that the tube joint clip is on the collar of the fuel tube joint.
    4. After installing the tube joint clip, check that the fuel tank main tube cannot be pulled out.



    A216407
  1. Connect the fuel pump connector.



4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


5. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

      NOTICE:
      Do not start the engine.

    3. Turn the Techstream on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    5. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there is no fuel leakage after performing maintenance anywhere on the fuel system. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the Techstream from the DLC3.



6. INSTALL REAR FLOOR SERVICE HOLE COVER


    A216406
  1. Install the rear floor service hole cover with new butyl tape.



7. INSTALL REAR SEAT CUSHION ASSEMBLY


    B311726E01
  1. Engage the 2 guides of the seat cushion to the seatback.
    Text in Illustration 
    *1
    Guide
    *2
    Hook

  1. Engage the 2 front hooks of the seat cushion to the vehicle body.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

    HINT:
    Confirm that the seat cushion is firmly installed.



8. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



9. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



10. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



11. PERFORM INITIALIZATION
  1. Perform "Inspection After Repair" after replacing the fuel pump (Click here).