Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A95-123    High Voltage Fuse

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
P0A95-123
The high voltage fuse is abnormal and voltage between VB9 and VB10 terminals is below the specified value despite the interlock switch being connected.
(1 trip detection logic)
  1. Service plug grip
  2. HV battery assembly

Related Data List 
DTC No.
Data List
P0A95-123
Battery Block Vol
The following items can be helpful when performing repairs:
Data List
  1. Ready Signal
  2. Inter Lock Switch

WIRING DIAGRAM


A219393E05


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

    HINT:
    At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

HINT:
  1. After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. Turn the power switch on (IG) and wait for 10 seconds or more.
  2. The interlock switch opens when the service plug grip is removed.

1.CHECK DTC OUTPUT (DTC P0AFC-123 IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check and record any HV system DTCs, INF codes and freeze frame data.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Disconnect the Techstream from the DLC3.



B
GO TO DTC CHART (Click here)
A


2.CHECK SERVICE PLUG GRIP
  1. Turn the power switch off.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



    A212489E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Standard Resistance
    Service plug grip
    Below 1 Ω



NG
Go to step 3
OK

REPLACE HV BATTERY ASSEMBLY (Click here)  

3.REPLACE SERVICE PLUG GRIP (HV)
(Click here)

NEXT


4.RECONFIRM DTC OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch off and wait for 30 seconds or more.

  1. Turn the power switch on (READY) and wait for 30 seconds or more.

  1. Turn the power switch on (IG) and wait for 30 seconds or more.

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs are not output.
    A
    DTCs are also output.
    B

  1. Disconnect the Techstream from the DLC3.



B
GO TO DTC CHART (Click here)
A

RECOVERY TO NORMAL